IBM Power System LC922 User manual

IBM Power System LC922 (9006-22P)
Quick Install Guide
IBM

This 2020-01-22 edition applies to IBM® Power Systems servers that contain the POWER9™ processor and to all
associated models.
© Copyright International Business Machines Corporation 2018, 2019.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with
IBM Corp.

IBM Power® System LC922 (9006-22P) Quick Install
Guide
The IBM Knowledge Center is available online from: http://www.ibm.com/support/knowledgecenter/
POWER9/p9hdx/9006_22p_landing.htm.
• Read all precautions and instructions before you start working on key parts.
• Use normal electrostatic discharge (ESD) procedures when working on the system and parts. IBM
recommends wearing gloves and an anti-static wrist strap to avoid possible damage to the equipment.
© Copyright IBM Corp. 2018, 2019 1

2 IBM Power System LC922 (9006-22P) Quick Install Guide

9006-22P parts
Figure 1. Rack nal assembly
© Copyright IBM Corp. 2018, 2019 3

Figure 2. System parts
4 IBM Power System LC922 (9006-22P) Quick Install Guide

Rear ports
Figure 3. Rear ports
Table 1. Input and output ports
Identier Description
1 USB 2.0 used for keyboard and mouse.
Certain USB drives might be too wide to t properly
into the USB ports on the rear of the system. Test
the t of your USB drive before proceeding.
2 Ethernet Intelligent Platform Management
Interface (IPMI)
3 Serial IPMI
4 Video Graphics Array (VGA) used for monitor. Only
the 1024 x 768 at 60 Hz VGA setting is supported.
Only up to a 3-meter cable is supported. Only text-
based capability is supported.
© Copyright IBM Corp. 2018, 2019 5

6 IBM Power System LC922 (9006-22P) Quick Install Guide

Installing and Removing
Figure 4. Removing a power supply from the system
Figure 5. Releasing and opening the cover
Figure 6. Removing a front drive Figure 7. Removing the 3.5-inch drive from the tray
© Copyright IBM Corp. 2018, 2019 7

Figure 8. Removing a DOM
Figure 9. Removing a rear drive
Figure 10. Opening the rear drive tray
Figure 11. Disconnecting the drive signal cables the
drive power cables
8 IBM Power System LC922 (9006-22P) Quick Install Guide

Figure 12. Removing the disk drive backplane and
screws
Figure 13. Disconnecting the drive signal cables the
drive power cables from the system backplane
Figure 14. Disconnecting the drive signal cables and
the drive power cables from the disk drive
backplane
Figure 15. Removing a fan
Installing and Removing 9

Figure 16. Removing the memory DIMM
Figure 17. Single-processor plugging sequence
Figure 18. 9006-22P PCIe adapter positions
Figure 19. Removing the PCIe riser
Figure 20. Removing an adapter in position 1 from
the riser
Figure 21. Removing a position 2 adapter from the
riser
10 IBM Power System LC922 (9006-22P) Quick Install Guide

Figure 22. Removing position 1 riser card
Figure 23. Removing the PCIe riser Figure 24. Removing an adapter from the riser
Figure 25. Removing position 3, 5, or 6 riser card
Figure 26. Releasing the tail-stock
Installing and Removing 11

Figure 27. Screw locations Figure 28. Lifting out the system backplane
Figure 29. Opening the system processor module
packaging
Figure 30. Loosening the load arm screw of the heat
sink
12 IBM Power System LC922 (9006-22P) Quick Install Guide

Figure 31. Lifting the heat sink from the load arm
Figure 32. Lowering the removal tool onto the
system processor module
Installing and Removing 13

Figure 33. Locking the system processor module
into the tool
Figure 34. Lifting the system processor module from
the packaging tray
14 IBM Power System LC922 (9006-22P) Quick Install Guide

Figure 35. Installing the system processor module
Figure 36. Installing the heat sink
Figure 37. Tightening the load arm screw
Installing and Removing 15

Figure 38. Time-of-day battery location
Figure 39. Removing the TPM card
16 IBM Power System LC922 (9006-22P) Quick Install Guide

IBM®