Ice IB2000 Programming manual

Operator & Parts Manual
Floor Burnisher
www.icecompanies.com
5015011
REV.01(04-2014)
IB2000
INTERNATIONAL CLEANING EQUIPMENT

HOW TO ORDER PARTS
Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered
online,by phone, by fax or by mail.
1. Identify the machine model.
2. Identify the machine serial number from the data label.
3. Ensure the proper serial number is used from the parts list.
4. Identify the part number and quantity.
Do not order by page or reference numbers.
5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
Please ll out at time of installation for future reference.
Model No.
Serial No.
Machine Options
Sales Rep.
Sales Rep. phone no.
Customer ID Number
Installation Date
READ OPERATOR MANUAL CAREFULLY
International Cleaning Equipment
XiangShi Road LiaoBu DongGuan GuangDong China
Tel:[phone]
Fax:[phone]
Specifications and parts are subject to change without notice.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials,old machine components
such as batteries,
hazardous uids, including antifreeze and oil, in an environmentally
safe way according to local waste disposal regulations.
Always remember to recycle.
ICE IB2000 2
IMPORTANT:To ensure full warranty protection,Please ll out
& return your warranty card.

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
MACHINE OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . 6
MACHINE MAINTENANCE & STORAGE . . . . . . . . . . . . . . . . . 7
HANDLE AND AIR SPRING INSTALLATION . . . . . . . . . . . . . . . . . 8
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
WEAR & TEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3ICE IB2000
TABLE OF CONTENTS

SAFETY PRECAUTIONS
ICE IB2000 4
OPERATOR
Carefully read and understand this manual before operating this machine.
This machine must be grounded!
This oor/nishing machine shall be grounded while in use to protect the operator from electric
shock.Grounding provides a path of least resistance for electric current. This machine is
equipped with a cord having an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances. Do not remove the ground pin under any circumstances.
This machine is for use on a nominal 220-volt circuit
and has a grounding plug that resembles the plug
illustrated in Figure. Make sure that the machine is
connected to an outlet having the same conguration as
the plug. No adapter should be used with this machine.
This machine is intended for commercial use. It is constructed for use in an indoor environment
and is nor intended for any other use. Use only recommended accessories.
1. Do not operate machine:
– Unless trained and authorized. – Unless you have read and
– In ammable or explosive areas. understand the operators manual.
– With a damaged cord or plug. – With the use of extension cords.
– If not in proper operating condition. – In outdoor areas and standing water.
– Without bag / lters in place.
2. Before operating machine:
– Make sure all safety devices are in place and operating properly.
3. When using machine:
– Only use approved burnishing pads. – Do not run machine over cord.
– Do not pull machine by cord or plug. – Do not pull cord around sharp
– Do not stretch cord. edges or corner.
– Ensure the dust collection bag is in – Do not unplug by pulling on the cord.
place and is tightly sealed to the machine. – Do not handle plug with wet hands.
– Turn power switch to “off “ prior to – Keep cord away from heated surfaces.
unplugging machine. – Do not pick up burning or smoking
– Report machine damage or faulty debris such as cigarettes, matches
operation immediately. or hot ashes.
To avoid electrical shock,please replace the power cord immediately if any damage is
being detected. The replacement must be performed only by an authorized person or
by our customer service center.
4. Before leaving or servicing machine:
– Turn off machine. – Unplug cord from outlet.
5. When servicing machine:
– Unplug cord from outlet. – Use manufacturer supplied or
approved replacement parts.

13
MACHINE COMPONENTS
ICE IB2000
5
OPERATOR
Machine Description
• New structure design
• 20" Housing
• 20" Pad brush
• Engnieering plastics
• Buffer device, quiet, easy operation
• Universal clutch plate
• Safety lock-out switch
• Security protection in an upright
• Use Air Spring Adjustment Pad Pressure
• 50' Cord
Machine Structure
1. Brush Assy 2. Housing
3. Wheel 4. Handle
5. Safety lock-out switch 6. Trigger
7. Leveling rod 8. Handle housing
9. Motor cover 10. Cover dust bag
11. Air spring 12. Lock washer
13. Big mouth 14. Pad holder, 20"
14 12 11
9
10
56
7
8
1
2
3
4

OPERATION OF HIGH SPEED FLOOR MACHINE
ICE IB2000 ６
OPERATOR
General Use:
1) Remove any obstructions or other obstacles in the area which is to be cleaned.
2) Remove dust recovery bag and empty it out in a trash receptacle. Replace dust recovery bag
on machine, ensuring it is sealed tightly to the machine.
3) Place handle in upright position and tilt machine back until handle rests on the oor.
Be sure the machine is not plugged into an outlet.
7) Adjust the handle (switch housing) height to a comfortable operating position.
8)To start the machine, push on the Blue safety button of the top of upper switch housing and
squeeze either of the switch levers.
9) When the machine is in operation, both hands should be placed on the handle (switch
housing).
10)Once the machine has reached operating speed, look at the digital pad pressure meter
located on the top of the motor cover. There are 2 light colors which will help you determine
optimal pad pressure for operating the machine. YELLOW LIGHT(left): If one or both
yellow lights are illuminated, adjustment handle position to increase the pad pressure.
RED LIGHT(right): If one or both red lights are illuminated, adjustment handle position to
reduce the pad pressure. GREEN LIGHT(S): If one, two, three, or four green lights are
illuminated, the machine is running at the optimal pad pressure and you may begin working.
11) When the machine is in operating, both hands should be gripping the hand.
12)To stop the machine at any time, simply release the switch lever, and the machine will stop
automatically.
Do not use an extension cord in conjunction with the standard power cord.
4) Remove the pad center gripping device by unscrewing the thumbscrews.
5) Place a "ICE approved" burnishing pad on the pad driver and re-attach the
center gripping device. (check with your ICE distributor for approved pads)
6) Place machine back into its upright position.
THIS IS A SPECIALIZED MACHINE WHICH REQUIRES THE OPERATOR TO UTILIZE
A ICE APPROVED PAD, AND MUST BE ADJUSTED PROPERLY TO ENSURE THE
HIGHEST POSSIBLE PERFORMANCE AND PRODUCTIVITY.
Read operators manual thoroughly prior to operating or servicing this machine.
7) Plug power cord into grounded outlet.

ICE IB2000
７
OPERATOR
STORAGE
1) Unplug machine from power source and wrap cord on handle.
2) Store in upright position in a dry area.
MAINTENANCE
To keep the machine performing well for many years, please follow the following maintenance
procedures.
Always confirm that the machine is unplugged prior to performing any
maintenance or repairs.
1. Unplug machine as soon as you are done using it.
2. Remove dust recovery bag and empty contents into a trash receptacle.
inspect dust recovery bag for any damage prior to replacing it on the machine.
3. Clean the outside of the machine with a mild cleaner.
4.Check power cord for any damage. If any damage is detected, replace the cord immediately.
5. Lubricate wheels with a water resistant lubricant once a month.
6. Check machine for loose or missing nuts and bolts, and replace as necessary.
7. If the machine is used in a dusty environment, you may remove the motor cover and blow
the motor clean with compressed air. This will allow for good ventilation and help the motor run
cooler.
The motor is computer controlled, and utilizes computer circuitry. Do not allow
this circuitry to get wet! Never store a low speed machine with the pad driver
or brush mounted

ICE IB2000 ８
OPERATOR
Step1:Takeout accessory,
installthehandle toon the
housing.
Step2:Takeout Air Spring,
andtightenwith AirSpring
Holder.
Step3:Takeout M8 nutand
bolt,installtheAir Springand
handle, keep bothAir Spring
Holderparallel,andtheycan
rotate flexibly.
HANDLE AND AIR SPRING INSTALLATION GUIDE

PARTLIST
ICE IB2000
９
IB2000 HANDLEASSEMBLY

ICE IB2000 １０
DIA
NO PART NUMBER NO REQ'D
11031825 HEXSCREWM8x25 1
21113507 NUTLOCK M5 12
35014009 HANDLE ADJUSTMENTRIGHTBRACKET 1
41212410 SCREWM4X10 2
54010212 COVER 2
65011002 GEAR 1
74010201 MOUNTING BASE GEAR 1
81511525 SCREWM5 X25 HEXSOCKET 2
91511530 SCREWM5 X30 HEXSOCKET 2
10 1011555 HEXSCREWM5x55 2
11 1123810 NUTLOCK M8 1
12 5014008 HANDLE ADJUSTMENTLEFTBRACKET 1
13 5014006 SPACER_1 2
14 4010202 COVER SEATGEAR 1
15 5011003 INSERT 1
16 1111605 NUTM6 1
17 4010208 SPRING LEVELING 1
HANDLE ASSEMBLY PARTS LIST
DESCRIPTION
18 5011016 SEATSPRING 1
19 5011009 ROD LEVELING 1
20 5011022 TUBING BOTTOM BRACKET 1
21 1647845 PIN 1
22 5011019 TUBING BOTTON BASE 1
23 4010405 HOOK CABLE 1
24 1511540 SCREWM5 X40 HEXSOCKET 2
25 1434500 TOOTH WASHER 5 4
26 1211512 SCREWM5X12 4
27 1434400 TOOTH WASHER 4 2
28 1221412 SCREWM4X12 1
29 5011017 LEVELING ROD 1
30 4010314 PIN 3
31 5011004 COVER 1
32 4010318 CORD POWER SUPPLY 1
33 4010310 STRAIN RELIEF CORD 1
34 1421616 WASHER PLAIN Ø6 4
35 1512635 SCREWM6 X35 2
36 5015001 SERIAL NUMBER 1
37 1512625 SCREWM6 X25 2
38 4010302 REAR COVER 1

ICE IB2000
１１
DIA
NO PART NUMBER NO REQ'D
39 4010333 SAFETYSPRING 1
40 4010317 BALL BASE 1
41 1211408 SCREWM4X8 2
42 4010330 LEFTTRIGGER SWITCH 1
43 4010331 RIGHTTRIGGER SWITCH 1
44 1211325 SCREWM3X25 2
45 4010323 SPRING SAFETY 1
46 1434300 TOOTH WASHER 2
47 4010308 SWITCH 1
48 4010307 SAFETYBOTTOM 1
49 4010301 FRONTCOVER 1
50
4010316
ICE LOGO
1
HANDLE ASSEMBLY PARTS LIST
DESCRIPTION
50
4010316
ICE LOGO
1
51 4010311 CLAMP CORE 1
52 1221406 SCREWM4X6 2
53 1123608 NUTLOCK M6 1
54 1421612 WASHER Ø6 6
55 4010403 CLAMP HOOK 1
56 4010215 CORD HANDLE 1
57 4010213 GROMMET 1
58 5011021 TUBING TOP BRACKET 1
59 5011018 TUBING TOP BASE 1
60 1644045 PIN 1
61 1221620 SCREWM6X20 6
62 1422616 WASHER, LOCK, 6 6

PARTLIST
ICE IB2000 １２
IB2000 BASEASSEMBLY

ICE IB2000
１３
DIA
NO PART NUMBER NO REQ'D
14010316 ICE LOGO 1
25015006 BRUSH ADJUSTMENTDECAL 1
35013010 PCB ASSEMBLY 1
41222416 SCREWM4x16 2
51123406 NUTLOCK M4 5
65012414 COVER MOTOR 1
71421409 WASHER PLAIN 4× 9×0.8 8
81221410 SCREWM4x10 PH 8
5012304 MOTOR 1.5KW220v 1
5015009 MOTOR LABEL 1
10 1521845 SCREWM8 X45 HEXSOCKET 3
11 5012416 HANDLE STAND LEFT 1
5014002 AIR SPRING 1
5015007 AIR SPRING LABEL 1
13 5012415 HANDLE STAND RIGHT 1
14 1521620 SCREWM6 X20 HEXSOCKET 11
15 4010114 WASHER 1
16 1222512 SCREWM5x12 1
17 5012410 HOUSING 1
12
9
BASE GROUP PARTS LIST
DESCRIPTION
18 5014010 SPACER 2
19 1123810 NUTLOCK M8 3
20 1411612 WASHER, PLAIN 6.4× 12×1.6 15
21 1422616 WASHER, LOCK, 6 11
22 1121605 NUT,M6 4
23 1031840 HEXSCREWM8x40 1
24 5012407 REAR AXLE 1
25 5012408 SPACER WHEEL AXLE 2
26 1436012 RETAINING RING, EXTERNAL, Φ12 4
27 4210115 WHEEL, 6" 2
28 4010111 HEXSCREW, M6x12.7 4
29 1421625 WASHER, PLAIN 12.5× 25×1.5 4
30 4210116 WHEEL, 5" 2
31 5012406 FRONTAXLE 1
32 5012305 SPACER 1
33 5012308 DRIVING PULLEY 1
34 5012603 VEE BELT 1
35 5012205 KEY, DRIVEN SHAFT 1
36 1534608 SCREW, M6x8 4
37 5012306 KEY, MOTOR 1
38 5012303 WASHER, PLAIN, Φ8xΦ30x5 2
39 1422821 WASHER,LOCK, 8 2

ICE IB2000 １４
DIA
NO PART NUMBER NO REQ'D
40 1021825 SCREW, M8x25, HEX 1
41 5012101 HOUSING 1
42 9060020 PAD HOLDER, 20" 1
43 5012112 FLEXIBLE SKIRT 1
44 9000001 BIG MOUTH 1
45 1031830 SCREW, M8x30, HEX 1
46 1221508 SCREWM5X8 3
47 5012106 HOOK, COVER, DUSTBAG 1
48 5012105 DUSTCOLLECTOR BAG 1
49 5012201 DRIVEN PULLEY 1
50 1612607 BEARING, 6004LU TPI 2
51 5012203 DRIVEN SHAFT 1
52 5012204 SPACER, BEARING 1
53 1437042 RETAINING RING, INTERNAL, 42 2
54 1111008 NUT, M10 5
55 1021065 SCREW, M10x65, HEX 1
56 1011025 SCREW, M10x25, HEX 4
57 1031032 SCREW, M10x32, HEX 4
58
5012202
MOUNTING PLATE, DRIVEN SHAFT
1
DESCRIPTION
BASE GROUP PARTS LIST
58
5012202
MOUNTING PLATE, DRIVEN SHAFT
1
59 1432026 WASHER, LOCK, 10 8
60 1421020 WASHER, PLAIN 10 16
61 1221614 SCREWM6x14 PH 1
62 1123305 NUT,LOCK,M3 4
63 5013005 RELAY 1
64 1143315 NUT, M3x15 4
65 1221306 SCREWM3X6 4
66 4210113 CAPACITOR CLIP 1
67 5013001 START-UP CAPACITOR, 200uF/250V 1
68 5013002 RUNNING CAPACITOR, 45uF/450V 1
69 5013004 MOTOR POWER CORD 1
70 6150712 WIRE CLIP 1
71 4010110 SHAFT 1
72 1421516 WASHER, PLAIN, 5x 16 1
73 1221515 SCREWM5X15 1
74 5014006 SPACER 1
75 5012102 COVER, DUSTBAG 1
76 1113507 NUT,LOCK,M5 1
77 5015004 WARNING DECALL 1
78 1031845 SCREW, M8x45, HEX 1
79 5012113 COVER, DUSTBAG BRACKET 1
80 8118003 HANDLE 1

OPERATOR
DIA
NO PART NUMBER NO REQ'D
1 4210115 WHEEL, 6" 2
2 5012603VEE BELT 1
3 4210116 WHEEL, 5" 2
98×62×52 cm
Weight
Dimension L×W×H
2 Hp
220 V
1.2 L
20" (51cm)
2000 rmp
15 m
62 dB(A）
48.5 Kg
Power
Voltage
Capacity
Working Width
Brush Speed
Cable Length
DESCRIPTION
WEAR & TEAR PARTS
SPECIFICATIONS
Model IB2000
Sound Level
ICE IB2000
１５

OPERATOR
WiringDiagram
IB2000
G/Y Brown Blue SWITCH
50/60HZ Phase Power Single 220V
Motor
Supply
Handle
Cord Motor
Cord
SwitchHousing
PCB
G/Y Black White
85 86 87 30
RELAY
White white
Startup
Capacitor
200 F/250V
Red
Red
Running
Capacitor
45 F/450V
ICE IB2000 １６