Ice iE410 Programming manual

Operator & Parts Manual
Self_Contained Extractor
www.icecompanies.com
6210149U
REV.05(11-2016)
iE410
INTERNATIONAL CLEANING EQUIPMENT

SAFETY PRECAUTION. . . . . . . . . . . . . . . . . . . . . 2
MACHINE SET-UP. . . . . . . . . . . . . . . . . . . . . .3
MACHINE OPERATION. . . . . . . . . . . . . . . . . . . .3-4
MACHINE MAINTENANCE & STORAGE . . . . . . . . . . . . . . . . . . . .5
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . .6
MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-19
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
WEAR & TEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
ICE iE410 1
TABLE OF CONTENTS

SAFETY PRECAUTION
2ICE iE410
OPERATOR
Carefully read and understand this manual before operating this machine.
This machine must be grounded!
This machine shall be grounded while in use to protect theoperator from electric shock.
Grounding provides a path of least resistance for electric current. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances. Do not remove the ground pin under any circumstances.
This machine is for use on a nominal 120-volt circuit
and has a grounding plug that resembles the plug
illustrated in Figure. Make sure that the machine is
connected to an outlet having the same conguration as
the plug. No adapter should be used with this machine.
This machine is intended for commercial use. It is constructed for use in an indoor environment
and is nor intended for any other use. Use only recommended accessories.
1. Do not operate machine:
– Unless trained and authorized. – Unless you have read and
– In ammable or explosive areas. understand the operators manual.
– With a damaged cord or plug – With the use of extension cords.
– If not in proper operating condition. – In outdoor areas and standing water.
2. Before operating machine:
– Make sure all safety devices are in place and operating properly.
3. When using machine:
– Do not run machine over cord. – Do not pull machine by cord or plug.
– Do not pull cord around – Do not unplug by pulling on the cord.
sharp edges or corners. – Do not stretch cord.
– Do not handle plug with wet hands. – Keep cord away from heated surfaces.
– Report machine damage or faulty
operation immediately.
To avoid electrical shock,please replace the power cord immediately if any damage is
being detected. The replacement must be performed only by an authorized person or
by our customer service center.
4. Before leaving or servicing machine:
– Turn off machine. – Unplug cord from outlet.
5. When servicing machine:
– Unplug cord from outlet. – Use manufacturer supplied or
approved replacement parts.

ICE iE410 3
OPERATOR
SELF-CONTAINED EXTRACTOR SET-UP
Carefully check the shipping carton for signs of damage. Report any carton damage to carrier
immediately.
Read operators manual thoroughly prior to operating or
servicing this machine!!!
Check carton contents to ensure carton is complete. Contact your ICE distributor if anything is
missing.
Contents:
- Carpet Extractor - 50’ extension power cable
Read operators manual thoroughly prior to operating or servicing
this machine!!!
1. Using a hose or bucket, ll tank with a maximum of 10 gallons of hot water.
2. Add distributor recommended cleaning solution.
Do not use flammable liquids or operate machine in or near
flammable liquids or vapors!!!
3. Connect the supplied extension power cable to the machine. Plug cord into a grounded wall
outlet. (see grounding instructions)
4. Drop the brush head to the oor with the foot release pedal on the back
of the machine.
MACHINE OPERATION
PRIOR TO EXTRACTING CARPETS
1. Inspect power cable and extension cable for damage. Replace cable if damage is found.
2. Vacuum carpet to remove debris prior to extracting carpet.
CARPET EXTRACTING
1. Turn on vacuum / pump switch.
NOTE: Solution will only spray when the brush / spray button is pushed.
2. To start cleaning, push the brush / spray button and begin to pull the machine backwards.
NOTE: For best cleaning results, pull back on the machine at a pace of approx. 10 feet in 15
seconds.
3. Release brush / spray button at the end of the path, and continue to pull machine back for
another 12 inches to pick up excess solution.
4. Tip machine back onto the transport wheels and push forward to begin next path.
5. During pickup, the oat shut-off will automatically prevent water from entering the
recovery tank once the recovery tank is full.

4 ICE iE410
OPERATOR
OPERATING HINTS
1. Overlap cleaning path by approx. 2 inches
2. Work away from power outlet and power cable in order to avoid damage to the power
cable.
3. Continually check for foam buildup in recovery tank. Use a distributor recommended foam
control solution.
NOTE: Excessive foam buildup will not activate the oat shut-off and may cause damage to
the vacuum motor.
4. Repeat extraction path on heavily soiled areas.
5. If brush stops spinning, there may be an obstruction in the brush. Unplug the power cable,
raise the brush off the oor and check for an obstruction. Check & reset the brush circuit
breaker located on the control housing.
6. When recover of the dirty solution ends, or the solution tank is empty, you must drain the
recovery tank. (see TANK DRAINING)
USE OF ACCESSORY TOOLS
NOTE: Prior to cleaning upholstery, be sure to read cleaning instructions provided by the
manufacturer.
1. Disconnect black vacuum hose off the back right side of the machine. Connect accessory
vacuum hose to area where the standard vacuum hose was removed.
2. Connect accessory solution hose to brass quick connect coupler located on the back of the
machine.
3. Connect accessory tool to solution and vacuum hoses.
4. Turn on vacuum / pump switch.
5. Operate accessory tools as needed.
6. When cleaning is completed, relieve water pressure from solution lines by turning off
vacuum / pump switch and then squeeze trigger for 4 seconds.
DRAINING TANKS
DRAINING SOLUTION TANK
1. To drain any remaining water from the solution tank,pull the solution tank level hose off the
hose tting.
2. Drain dirty solution into oor drain.
3. Reattach the hose to the hose tting.
DRAINING RECOVERY TANK
1. Turn off machine, unplug and remove power cable.
2. Unhook drain hose off the back of the machine and remove drain hose stopper.
3. Drain dirty solution into oor drain.
4. Replace drain hose stopper and reattach hose to back of machine.
NOTE: If foam develops in the recovery tank during vacuuming, use de-foamer chemical to
help eliminate the foam. Foam will not activate the float shut-off, and therefore, may cause
vacuum motor damage.

ICE iE410 5
OPERATOR
MACHINE MAINTENANCE
To keep the machine performing well for many years, please follow the following maintenance
procedures.
Always conrm that the machine is unplugged prior to performing any maintenance or
repairs!!!
DAILY MAINTENANCE
1. When cleaning operation is complete for the day, drain and rinse the recovery tank
thoroughly with clean water.
2. Remove remaining solution from solution tank.
3. Remove oat shut-off (ping pong ball in cage) from recovery tank and clean with water.
4. Remove and inspect spray jets. If necessary, clean jets in acetic acid solution.
Do not clean brass jets with a pointed object, as it will damage the jets.
5. Check brush assembly & remove any debris or carpet bers.
6. Check pick up head and remove any debris or carpet bers.
7. Check condition of the stainless steel pickup shoes on the pickup head. The shoes must
contact the oor for the whole length of the pickup head. Replace as necessary.
8. Clean machine with a nonabrasive cleaner.
9. Inspect power cable for any damage. Replace if necessary.
MONTHLY MAINTENANCE
1. Flush pump & plumbing with an acetic acid solution to dissolve any chemical buildup.
Mixing Instructions:
a) Premix 16 oz. or an acetic acid solution with 2 gallons of water and pour into solution tank.
b) Turn vacuum / pump switch on
c) Put machine head over oor drain and operate machine for 50 seconds.
d) Shut machine down and allow remaining solution to sit in machine overnight.
e) The following day, spray out remaining solution and ush system again with 3 gallons of
clean water.
2) Inspect machine for water leaks.
3) Lubricate wheels with a water resistance lubricant.
MACHINE STORAGE
1. Prior to storing the machine, ensure the solution and recovery tanks are clean and empty
of any solution.
2. Store machine in upright position in a dry area, with the brush head off the oor.
3. Remove recovery tank clear lid to allow for air circulation.
If you are storing the machine in an area which can freeze, be sure both tanks and
the solution plumbing are empty of all water and dry!

6 ICE iE410
OPERATOR
BASIC TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Machine doesn't
work
Not plugged in to power source Plug into a grounded outlet
Faulty power cable Contact ICE Distributor
Faulty extension power cable Replace with new extension
power cable
Building circuit breaker tripped Reset circuit breaker
Solution pump not
working
Vacuum / pump switch not on Turn on switch
Vacuum / pump switch faulty Contact ICE Distributor
Faulty solenoid Contact ICE Distributor
Faulty solution pump Contact ICE Distributor
Pump overheated Determine cause and allow 30
minutes for pump to cool
Loose or broken wiring Contact ICE Distributor
Vacuum motor not
working
Vacuum / pump switch not on Turn on switch
Vacuum / pump switch faulty Contact ICE Distributor
Vacuum motor thermal overload
tripped
Check for obstruction and allow
30 minutes to cool
Faulty vacuum motor Contact ICE Distributor
Worn carbon brushes Contact ICE Distributor
Loose or broken wiring Contact ICE Distributor
Poor pick up Air leaking around clear recovery
lid
Ensure recovery lid is firmly
tightened
Clogged oat shut-off Remove float shut-off and clean
off debris
Float shut-off is activated Drain recovery tank
Loose drain hose stopper Ensure stopper is securely in
place
Loose vacuum hose connections Ensure vacuum hose connections
are tight
Defective vacuum hose Replace vacuum hose
Loose vacuum hose cuffs Ensure cuffs are secure to the
hose
Damaged or loose pickup head
shoes
Contact ICE Distributor
Pulling machine too fast Slow down cleaning operation
Uneven or no
solution spray
Solution tank is empty or low Fill solution tank
Vacuum / pump switch not on Turn on switch
Dirty or plugged spray tips Clean or replace spray tips
Improper spray tip size or spray
angle
Contact ICE Distributor
Worn spray tips Contact ICE Distributor
Faulty solution pump Contact ICE Distributor
Plugged solution tank lter Clean or replace lter
Pinched or kinked solution hose Check for obstructions and kinks
and reroute or replace if needed

MACHINE COMPONENTS
ICE iE410 7
OPERATOR
1. Vacuum/Pump ON/OFF switch 2. Brush circuit breaker
3. Brush/spray ON/OFF switch 4. Drain hose
5. Accessory tool solution hookup
6. Brush raise and lower foot pedal
7. Spray jets 8. Brush assembly
9. Pickup head 10. Solution tank ll port
11. Clear dome
10
4
7
8
5
1
9
3
2
6
11

8 ICE iE410
OPERATOR

ICE iE410 9
OPERATOR
PARTS LIST
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
1 2320216 Clear Dome 1
2 2320218 Gasket,Clear Dome 1
3 2320217 Rubber Hinge 1
4 1421409 Washer,Plain,Φ4.3XΦ9X0.8 4
5 1321210 Screw, Ph, St4 X10 4
6 1221410 Screw, Ph, M4 X10 2
7 6210109 Bend, Tube 1
8 6210104 Coupler 1
9 6210103 Gasket,Coupler 1
10 6210108 Elbow 1
11 6210114 Coupler,Vac Hose 1
12 2230131 Plug, Serial number:000000-001234 1
13 6210705 Drain Hose, Serial number:000000-001234 1
8011030 Drain Hose,Serial number:001235- 1
14 6210113 Vac Hose 1
15 1962050 Clamp, Hose 2" 1
16 1021610 Screw, Hex, M6X10,SST 1
17 1422616 Washer, Lock, SST, Ø6 1
18 1421617 Washer, Plain, Φ6XΦ16X2 1
19 6150712 Clamp, Cord 1
20 6210503 Rocker Switch 1
21 6210502 Push Button Switch 1
22 6210504 Circuit Breaker, 2A 1
23 1221512 Screw, M5X12, PH 3
24 6210111 Clamp, Drain Hose 1
25 6210125 Warning Decal 1
26 6210501 Switch Housing 1
27 4020310 Strain Relief 1
28 6210518 Power Cord 1
29 6210505 Elbow Corrugated Tubing Fitting 1
30 6210506 Corrugated Tubing 1
31 6210136 Barb, Right Angle 1
32 6210135 Tubing 1
33 6180163 Barb, Hose 1
34 6180126 Nut, Coupling 1
35 6120667 Washer, Lock, Internal Toooth 1
36 6160509 Gasket, Solution, Intake 2
37 6120276 Washer, Plain 1
38 6180125 Coupling 1
39 6110411 Strainer, Line 1

10 ICE iE410
OPERATOR
PARTS LIST
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
40 1962025 Clamp(16-25) 1
41 4010316 Logo 3
42 6210101 Solution Tank 1
43 6210107 Filter 1
44 1321310 Screw, ST4.8X9.5 2
45 6210102 Recovery Tank 1
46 8111015 Float, Shut-off 1
47 2320220 Bend 1
48 8014043 Cord Wrap 1
49 6210519U Power Cord 1
50 6210508 Circuit Breaker, 17A 1

ICE iE410 11
OPERATOR

12 ICE iE410
OPERATOR
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
1 6180208 Coupler, Quick Connect 1
2 1421432 Washer, Plain ,Ø13.5XØ32X1.5 1
3 1421428 Washer, Plain ,Ø14XØ32X1.5 1
4 6180115 Elbow, Strect, 45°1
5 6180128 Barb, Hose 2
6 1962016 Clamp, Hose 3/8" 6
7 6210116 Hose, High Pressure 1
8 6210607 Barb,Pump 1
9 6210604U Solution Solenoid, 120V/60HZ 1
10 6210606 Connector, Three-way 1
11 6210603 Connector 1
12 6210602 Barb, Pump 1
13 6210601 Mounting Frame, Pump 1
14 6150195 Pump,115V,100PSI 1
15 2310116 Gasket, Vac Motor 1
16 2310135A Vac Motor,3-STAGE 120V (With terminal) 1
17 1421617 Washer, SST,Plain,Ø6XØ16X2 11
18 6180210 Bend, Nylon, Pump 1
19 6210117 Hose, Solution 1
20 2310122 Stud 3
21 1914300 Tie, Cable 1
22 2320208 Acoustic Insulation Pipe 1
23 1123608 Nut,Lock,SS,M6 3
24 1121605 Nut,SST,M6 4
25 6110011 Cap, Axle 2
26 1422616 Washer, Lock, Ø6 5
27 8111020 Cable 1
28 6210105 Spacer 2
29 1222515 Screw, FH, M5X15, SST 8
30 6160406 Hinger,SST 4" 2
31 1222520 Screw,FH,SST, M5X20 6
32 1221616 Screw,SST,PH,M6X16 2
33 1962050 Clamp, Hose 2" 1
34 1421515 Washer,SST,PLAIN,Ø5XØ15X1 10
35 1422513 Washer, Lock, Ø5 10
36 1121505 Nut,SST,M5 6
37 6210140 Carpet Pick-up Tool 1
38 6210407 Spring 1
39 6210400U Mounting Base Assy, Brush 1
PARTS LIST

ICE iE410 13
OPERATOR
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
40 6210110 Shoulder Screw 2
41 6210115 Hose, Spraying 1
42 6210130 Clamp 1
43 1221416 Screw, RHM,M4X16,SST 1
44 2320403 Strainer 1
45 1221425 Screw, RHM,M4X25,SST 1
46 1123406 Nut, Nylon, Insert, M4 2
47 6210106 Spacer 4
48 1021640 Screw, M6X40,Hex 1
49 6210305 Bracket, Foot Step 1
50 1221515 Screw, RHM, M5X15, SST 4
51 1123507 Nut, Lock, SST, M5 4
52 2320209 Foot Step 1
53 1021625 Screw, RHM, M6X25, SST 2
54 6160113 Washer, Wheel, AL 2
55 2320228 Wheel, 10" 2
56 1113304 Kep nuts, M4 5
57 1221530 Screw,RHM,M5X30,SST 4
58 6210200 Bottom Plate Assy 1
59 6210505 Elbow Corrugated Tubing Fitting 1
60 1221616 Screw,SST,PH,M6X16(NYLOCK) 2
PARTS LIST

14 ICE iE410
OPERATOR

ICE iE410 15
OPERATOR
PARTS LIST
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
1 6210403 Lift Bar 1
2 6210423 Rectifier 1
3 1422513 Washer Lock SST Ø5 5
4 1121505 Nut SST,M5 5
5 1221530 Screw SST PH M5X30 2
6 1221525 Screw, PH,SST,M5X25 1
7 6210407 Spring 1
8 1221514 Screw PH SST M5X14 2
9 1421515 Washer PLAIN Ø5XØ15X1 6
10 6210401 Mounting Base Brush 1
11 6180128 Barb Hose 1
12 6140330 Insert Sprayer Body 2
13 6210421 Sprayer Body 1
14 6110421 Strainer 3
15 6210435U Motor, 120V 1
16 6210433 Gasket 1
17 6210431 Bottom Plate 1
18 1221512 Screw BH M5X12 SST 10
19 1213520 Screw FH SST M5X20 4
20 6210412 Brush 1
21 6210417 Gasket 2
22 6210414 Frame Brush 2
23 6210406 Gasket 1
24 6210404 Plate 1
25 1611629 Bearing 2
26 1632512 Seal 2
27 6210411 Shaft Brush 1
28 6210413 Axle Pulley 1
29 6210416 Spacer 1
30 1521408 Screw Hex Socket 4
31 6210415 Driven Pulley 1
32 6210402 Belt 1
33 6210432 Driving Pulley 1
34 6210426 Caps,Nozzle Bodies 3
35 6180574 Tip-Nozzle, Spray,SST 110 3
36 6210425 Adapters 3
37 6210436 Mounting Bracket,Motor 1
38 1421617 Washer,SST,Plain,Ø6XØ16X1.5 4
39 1422616 Washer, Lock, Ø6 4
40 1121605 Nut,SST,M6 7
41 2320403 Strain Relief 1
42 6210408 Power Cord 1
43 6160515 Gasket 2
44 6210410 Brush Assembly 1

16 ICE iE410
OPERATOR

ICE iE410 17
OPERATOR
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
1 6140328 Upholstery Tool 1
2 6140327 Window, Hand Tool 1
3 1023806 Screw,5/16-18X5/8"L,HH 1
4 1421816 Washer, Plain, Ø8XØ16.5X1 1
5 6160531 Gasket 1
6 6180159 Nozzle, Spray Tip, 80º 1
7 6180105 Bushing, Brass 1
8 6180115 Elbow, Street, 45 Degrees 1
9 6110933 Trigger Valve 1
10 6180128 Barb, Hose 1
11 1962016 Clamp, Hose 3/8” 2
12 6185317 Solution Hose, 3/8” 1
13 6180241 Barb, Hose Mail Plug 1
PARTS LIST

18 ICE iE410
OPERATOR

ICE iE410 19
OPERATOR
PARTS LIST
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
16160215 Cuff 1 1/2” 2
26210703 Hose, Vacuum 1
31914300 Tie, Cable 16
46180241 Hose Barb/Mail Plug, SST 1
51962016 Clamp, Hose, SST 3/8” 2
66210704 Hose, Solution,16”L 1
76180128 Hose Barb 1
86180208 Couple, Quick Connect 1
96210703A Vacuum Hose Assembly 1
10 6210704A Solution Hose Assembly 1