Ice SCRUB 35D User manual

ORIGINAL INSTRUCTION DOC. 10067992 - Ver. AA - 02-2017
SCRUBBING MACHINES
USE AND MAINTENANCE MANUAL
SCRUB 35D

The descriptions contained in this document are not binding.
The company therefore reserves the right to make any modifications at any time to elements,
details, or the supply of accessories, as considered necessary for reasons of improvement or
manufacturing/commercial requirements.
The reproduction, even partial, of the text and drawings contained in this document is prohibited
by law.
The company reserves the right to make any technical and/or supply modifications. The images
are for reference purposes only, and are not binding in terms of design and supply.
Symbols used in the manual
Open book symbol with an "i"
Indicates the need to consult the instruction manual
Open book symbol
Used to tell the operator to read the manual before using the machine
Warning symbol
Carefully read the sections marked with this symbol and observe the
indications, for the safety of the operator and the machine
Warning symbol
Indicates danger of gas fumes and the leakage of corrosive liquids
Warning symbol
Danger of fire: do not go near with free flames
Disposal symbol
Carefully read the sections marked with this symbol for machine
disposal

33
CONTENTS
ON CONSIGNMENT OF THE MACHINE .................................................................................................................................................. 4
SERIAL NUMBER PLATE.....................................................................................................................................................................4
INTRODUCTION .................................................................................................................................................................................4
INTENDED USE..................................................................................................................................................................................4
TECHNICAL DESCRIPTION.................................................................................................................................................................. 5
SYMBOLS USED ON THE MACHINE......................................................................................................................................................6
GENERAL SAFETY REGULATIONS.......................................................................................................................................................7
MACHINE PREPARATION....................................................................................................................................................................9
1. HANDLING THE PACKAGED MACHINE...........................................................................................................................................9
2. HOW TO UNPACK THE MACHINE.................................................................................................................................................. 9
3. HANDLING AND TRANSPORTATION OF THE UNPACKAGED MACHINE............................................................................................... 9
4. TYPE OF BATTERY..................................................................................................................................................................... 9
5.BATTERY MAINTENANCE AND DISPOSAL................................................................................................................................ 10
6. INSERTING/CONNECTING THE BATTERIES..................................................................................................................................10
7. CONNECTING THE CONNECTOR................................................................................................................................................ 11
8. CHARGING THE BATTERY (WITH BUILT-IN BATTERY CHARGER) .................................................................................................... 11
9. BATTERY INDICATOR ............................................................................................................................................................... 12
10. INSTRUMENT PANEL COMPONENTS......................................................................................................................................... 12
11. FIXING THE HANDLEBARS....................................................................................................................................................... 13
12. SOLUTION TANK .................................................................................................................................................................... 13
13. DETERGENT SOLUTION.......................................................................................................................................................... 13
14. RECOVERY TANK................................................................................................................................................................... 14
15. ASSEMBLING THE BRUSH .......................................................................................................................................................14
WORK ............................................................................................................................................................................................15
1.PREPARING TO WORK ...............................................................................................................................................................15
2.OVERFLOW DEVICE...................................................................................................................................................................15
3.FORWARD MOVEMENTS ............................................................................................................................................................ 16
AT THE END OF THE WORK .............................................................................................................................................................. 17
DAILY MAINTENANCE ...................................................................................................................................................................... 18
1. CLEANING THE RECOVERY TANK ...............................................................................................................................................18
2.CLEANING THE SQUEEGEE ........................................................................................................................................................ 18
3.REPLACING THE SQUEEGEE RUBBERS ....................................................................................................................................... 19
4.DISASSEMBLING THE BRUSH...................................................................................................................................................... 20
PERIODIC MAINTENANCE ................................................................................................................................................................. 21
1.CLEANING THE SQUEEGEE TUBE................................................................................................................................................21
2.CLEANING THE SOLUTION TANK AND FILTER ...............................................................................................................................21
TROUBLESHOOTING........................................................................................................................................................................22
1.ELECTRICAL SYSTEM SAFETY ....................................................................................................................................................22
2.INSUFFICIENT WATER ON THE BRUSHES..................................................................................................................................... 22
3.THE MACHINE DOES NOT CLEAN WELL........................................................................................................................................22
4.THE SQUEEGEE DOES NOT DRY PERFECTLY ............................................................................................................................... 22
5.EXCESSIVE FOAM PRODUCTION................................................................................................................................................. 22
CHOOSING AND USING THE BRUSHES............................................................................................................................................... 23
MACHINE DISPOSAL ........................................................................................................................................................................ 24

4 54 5
On consignment of the machine
When the machine is delivered to the customer, an immediate check must
be performed to ensure that all the material mentioned in the shipping
documents has been received in addition to verifying that the machine
has not been damaged during transportation. If this is the case, the carrier
must ascertain the extent of the damage at once, informing our customer
service office. It is only by prompt action of this type that the missing
material can be obtained, and compensation for damage successfully
claimed.
Serial number plate
Introduction
SCRUB 35D is a floor scrubbing machine which, by means of the
mechanical action of the rotating brush and the chemical action of a
water/detergent solution, can clean any type of flooring. As it advances, it
also collects any removed dirt as well as the detergent solution not
absorbed by the floor.
The machine must only be used for this purpose. Even the best
machines will only work well if used correctly and kept in good working
order. We therefore suggest you read this instruction booklet carefully and
read it again whenever difficulties arise while using the machine. If
necessary, remember that our customer assistance service (organised in
collaboration with our dealers) is always available for advice or direct
intervention.
Intended use
The scrubbing machine is designed exclusively for the professional
cleaning of surfaces and floors in industrial, commercial and public
environments. The machine is only suitable for use in closed - or at least
covered - locations.
The machine is not suitable for use in the rain, or under water jets. It is
FORBIDDEN to use the machine for picking up dangerous dusts or
inflammable liquids in places with a potentially explosive atmosphere. In
addition, it is not suitable as a means of transport for people or objects.
Disconnect the quick connector before
removing the solution tank to gain access to
the serial number plate (see fig. page 18).

55
TECHNICAL DESCRIPTION UM SCRUB 35D
Rated power W 500
Working width mm 350
Width of rear squeegee mm 440
Work capacity m2/h 1050
Water consumption g/m2-
Brushes (diameter or length) mm 350
Brush rotations rpm 140
Pressure on the brushes kg 20
Brush motor V / W 12 / 250
Type of advance semi-aut.
Maximum gradient 2%
Suction motor V / W 12 / 250
Suction vacuum mbar -
Solution tank PE l 10
Recovery tank PE l 10
Total machine weight (including batteries) kg 67
Gross weight of the machine ready for use kg 77
Battery V/Ah 12 / 65
Battery charger V/
A
12/6
Battery compartment dimensions (Length / Height / Width) mm / mm / mm 277 / 224 / 172
Machine dimensions (Length / Height / Width) mm / mm / mm 682 / 1018 / 440
Length of the closed machine (without recovery tank) mm 795
Height of the closed machine (without recovery tank) mm 440
Noise level (in compliance with IEC 704/1) dB (A) 69.28
Vibration level m/s21.79

6 76 7
SYMBOLS USED ON THE MACHINE
Tap symbol
Used to indicate the solenoid valve switch
Brush symbol
Used to indicate the brush motor switch
Symbol denoting suction motor
Used to indicate the suction motor switch
Battery symbol
Battery charge level indicator
Indicates the maximum temperature of the detergent solution
Located near the solution tank inlet
Indicates the maximum gradient

77
GENERAL SAFETY REGULATIONS
The regulations illustrated below must be carefully followed in order to avoid harm to the operator and
damage to the machine.
Read the labels on the machine carefully. Do not cover them for any reason and replace them immediately
if they become damaged.
The machine must be used exclusively by authorised, trained personnel.
During the working of the machine, pay attention to other people and especially to children.
The machine is not suitable for cleaning carpets.
The socket for the battery charger cable must have a prescribed earth connection.
Avoid damaging the battery charger cable by crushing or bending it, or by applying stress.
If you notice any damage to the battery charger cable, contact a ICE technical assistance centre
immediately.
Do not mix different types of detergent as this may produce harmful gases.
Do not place any liquid containers on the machine.
The machine is designed for dry use only and should not be used or kept outdoors in wet conditions
The storage temperature must be between -25C and +55C; do not store outdoors in damp conditions.
Conditions of use: room temperature between 0C and 40C with relative humidity between 30 and 95%.
Do not use the machine in an explosive atmosphere.
Do not use the machine as a means of transport.
Do not use acid solutions which may damage the machine.
Avoid working with the brushes when the machine is standing still, so as not to damage the floor.
Do not vacuum inflammable liquids.
Do not use the device to collect dangerous powders.
In the event of a fire, use a powder extinguisher. Do not use water.
Do not knock against shelving or scaffolding, where there is a danger of falling objects.
If you use the machine where there is a risk of falling objects, the machine must be equipped with
protection devices against falling objects
Do not use the machine on surfaces with an inclination greater than the one shown on the plate.
The machine is designed to carry out the washing and drying operations simultaneously. Different
operations should only be carried out in areas where the passage of unauthorised persons is prohibited.
Signal the presence of damp floors with suitable signs.
If the machine does not work properly, check this is not caused by failure to carry out routine maintenance.
Otherwise, request the intervention of the ICE technical assistance centre.
If you need to replace any components, request the ORIGINAL spare parts from a ICE dealer and/or
Authorised Retailer.
Before carrying out any maintenance work, switch off the machine and disconnect the battery connector.
Do not remove any protection devices which require the use of tools in order to be removed.
Do not wash the machine with direct water jets or with pressurised water, nor with corrosive substances.
Have the machine checked by a ICE technical assistance centre every year.
To prevent scaling in the solution tank filter, do not fill the tank with detergent solution many hours before
using the machine.
Before using the machine, check that all the hatches and covers are positioned as shown in this Use and
Maintenance Manual.

8 98 9
When disposing of consumption materials, observe the laws and regulations in force.
When your ICE machine has reached the end of its long working life, dispose of the materials it contains
(especially oils and electronic components) in an appropriate manner, and bearing in mind that the machine
itself was constructed using 100% recyclable materials.
Only use the brushes supplied with the device, or those specified in the Use and Maintenance Manual
(page 19). The use of other brushes could compromise safety levels.
The device must be disconnected from the power supply before removing the battery.
The battery must be removed from the device before this is disposed of.
The battery and battery charger must be disposed of in a safe manner by scrupulously comply with
currently effective laws.
The machine is not suitable for use by children or people with reduced physical, mental and sensorial
capacities, or people lacking experience and knowledge, unless supervised and instructed in the use of the
machine by a person responsible for their safety.
Children must be supervised to ensure they do not play with the device.

99
A
CB
MACHINE PREPARATION
1. HANDLING THE PACKAGED MACHINE
The machine is contained within specific packaging.
Every pallet consists of four machines arranged on two levels.
It is not possible to place more than two packages on top of each other.
The total weight is 70kg
The overall dimensions of the package are:
A: 500 mm
B: 500 mm
C: 1150 mm
2. HOW TO UNPACK THE MACHINE
1. Open the packaging on the side indicated.
2. Take the machine out of its packaging.
3. Remove the recovery tank.
3. HANDLING AND TRANSPORTATION OF THE UNPACKAGED MACHINE
Vispa B is a machine that can be managed in all situations and transported without effort, even in small
vehicles.
Just lift the front part, using the machine handlebars as a lever. The big rear wheels mean it can be
towed anywhere and loaded on a truck by means of a simple ramp.
Vispa B is easy to transport even by car. Exploiting the full flexibility of the handlebars, you can fold it up
(see the handlebars fixing section) and, with the help of a colleague, place it in the boot of the car
without disassembling any components.
4. TYPE OF BATTERY
To power the machine it is necessary to use:
sealed traction batteries with gasrecombination or gel technology
OTHER TYPES MUST NOT BE USED.
The batteries must meet the requisites laid out in the norms CEI EN 60254-1:2005-12 (CEI 21-5) +
CEI EN 60254-2:2008-06 (CEI 21-7).
Every battery consists of DIN-type elements connected in series and providing the clamps with a power
of 12 V. You are advised to use batteries with an electric capacity of 65 Ah (C5)

10 1110 11
MACHINE PREPARATION
5. BATTERY MAINTENANCE AND DISPOSAL
For maintenance and recharging, comply with the instructions provided by the battery manufacturer.
Particular attention must be paid when choosing the battery charger, if not supplied, since there are
different kinds according to the type and capacity of the battery.
W
hen the battery reaches the end of its working life, it must be disconnected by expert, trained
personnel, then lifted (using the grips and suitable lifting devices) to remove it from the battery
compartment. DEAD BATTERIES ARE CLASSIFIED AS DANGEROUS WASTE AND MUST BE
DELIVERED TO THE AUTHORISED BODIES FOR CORRECT DISPOSAL.
Proceed as follows when the battery is dead:
1. Disconnect the quick connector and remove the solution tank.
2. Open the battery compartment and disconnect the connector.
Remove the battery using suitable devices by lifting with the provided handles.
WARNING: you are advised to always wear protective gloves in order to avoid
the risk of serious injury to your hands
WARNING: You are advised to only lift and move the batteries with lifting and
transportation means suitable for the specific weight and size
6. INSERTING/CONNECTING THE BATTERIES
The machine is supplied with a built-in battery charger and an airtight gel battery. If you use batteries
other than those supplied with the machine, use only 12V AGM or Gel batteries and proceed as follows.
The batteries must be housed in the special compartment beneath the solution tank.
To insert the batteries you must:
1. Disconnect the quick connector (1) at the front of the solution tank in order to avoid breakage of the
connector itself
2. Remove the solution tank and place it on the ground
3. Open the two rear hinges (2) that close the battery compartment
4. Rotate the handlebars, raising the handlebar movement lever (see “FIXING THE HANDLEBARS”)
5. Position the battery inside the compartment
6. Connect the cables
1
2