Ice SCRUB 35C User manual

ORIGINAL INSTRUCTION DOC. 10068611 - Ver. AA - 02-2017
SCRUBBING MACHINES
USE AND MAINTENANCE MANUAL
SCRUB 35C

The descriptions contained in this document are not binding.
The company therefore reserves the right to make any modifications at any time to elements,
details, or the supply of accessories, as considered necessary for reasons of improvement or
manufacturing/commercial requirements.
The reproduction, even partial, of the text and drawings contained in this document is prohibited
by law.
The company reserves the right to make any technical and/or supply modifications. The images
are for reference purposes only, and are not binding in terms of design and supply.
Symbols used in the manual
Open book symbol with an "i"
Indicates the need to consult the instruction manual
Open book symbol
Used to tell the operator to read the manual before using the machine
Warning symbol
Carefully read the sections marked with this symbol and observe the
indications, for the safety of the operator and the machine
Warning symbol
Indicates danger of gas fumes and the leakage of corrosive liquids
Warning symbol
Danger of fire: do not go near with free flames
Disposal symbol
Carefully read the sections marked with this symbol for machine
disposal

33
CONTENTS
ON CONSIGNMENT OF THE MACHINE .................................................................................................................................................. 4
SERIAL NUMBER PLATE.....................................................................................................................................................................4
INTRODUCTORY COMMENT ................................................................................................................................................................ 4
INTENDED USE..................................................................................................................................................................................4
TECHNICAL DESCRIPTION.................................................................................................................................................................. 5
SYMBOLS USED ON THE MACHINE ......................................................................................................................................................6
GENERAL SAFETY REGULATIONS.......................................................................................................................................................7
MACHINE PREPARATION ....................................................................................................................................................................9
1.HANDLING THE PACKED MACHINE...........................................................................................................................................9
2.HOW TO UNPACK THE MACHINE.............................................................................................................................................. 9
3.HANDLING AND TRANSPORTATION OF THE UNPACKED MACHINE...............................................................................................9
4.TYPE OF BATTERY............................................................................................................................................................... 10
5.BATTERY MAINTENANCE AND DISPOSAL................................................................................................................................10
6.INSERTING/CONNECTING THE BATTERIES............................................................................................................................. 10
7.CONNECTING THE CONNECTOR............................................................................................................................................ 11
8.RECHARGING THE BATTERIES ..............................................................................................................................................11
9.BATTERY INDICATOR ........................................................................................................................................................... 13
10.INSTRUMENT PANEL COMPONENTS.................................................................................................................................. 13
11.ASSEMBLING THE BRUSHES .............................................................................................................................................13
12.FIXING THE HANDLEBARS................................................................................................................................................. 14
13.SOLUTION TANK .............................................................................................................................................................. 14
14.DETERGENT SOLUTION.................................................................................................................................................... 14
15.RECOVERY TANK............................................................................................................................................................. 15
WORK ............................................................................................................................................................................................16
1.PREPARING TO WORK ...............................................................................................................................................................16
2.OVERFLOW DEVICE...................................................................................................................................................................17
3.FORWARD MOVEMENTS ............................................................................................................................................................ 17
AT THE END OF THE WORK .............................................................................................................................................................. 18
DAILY MAINTENANCE ...................................................................................................................................................................... 19
1. CLEANING THE RECOVERY TANK ...............................................................................................................................................19
2.CLEANING THE FRONT AND REAR SQUEEGEES............................................................................................................................ 19
3.CLEANING THE DEBRIS HOPPER................................................................................................................................................. 19
4. DISASSEMBLING THE BRUSH ....................................................................................................................................................20
WEEKLY MAINTENANCE................................................................................................................................................................... 21
1.REPLACING THE REAR SQUEEGEE RUBBERS .............................................................................................................................. 21
2.REPLACING THE FRONT SQUEEGEE RUBBERS............................................................................................................................. 21
3.CLEANING THE SQUEEGEE TUBE................................................................................................................................................ 22
4.CLEANING THE SOLUTION TANK AND FILTER ...............................................................................................................................22
TROUBLESHOOTING........................................................................................................................................................................23
1.ELECTRICAL SYSTEM SAFETY .................................................................................................................................................... 23
2.INSUFFICIENT WATER ON THE BRUSHES..................................................................................................................................... 23
3.THE MACHINE DOES NOT CLEAN WELL........................................................................................................................................ 23
4.THE SQUEEGEE DOES NOT DRY PERFECTLY ............................................................................................................................... 23
5.EXCESSIVE FOAM PRODUCTION................................................................................................................................................. 23
CHOOSING AND USING THE BRUSHES............................................................................................................................................... 24
MACHINE DISPOSAL ........................................................................................................................................................................ 25

4 54 5
On consignment of the machine
When the machine is delivered to the customer, an immediate check must
be performed to ensure all the material mentioned in the shipping
documents has been received, and also to check the machine has not
been damaged during transportation. If this is the case, the carrier must
ascertain the extent of the damage at once, informing our customer
service office. It is only by prompt action of this type that the missing
material can be obtained, and compensation for damage successfully
claimed.
Serial number plate
Introductory comment
SCRUB 35C is a scrubbing machine which / by means of the mechanical
action of the cylindrical brushes and the chemical action of a water-
detergent solution - can clean any type of floor. In addition, as it moves
forward it picks up removed dirt and the detergent solution not absorbed
by the floor.
The machine must be used only for this purpose. Even the best
machines will only work well if used correctly and kept in good working
order. We therefore suggest you read this instruction booklet carefully and
read it again whenever difficulties arise while using the machine. If
necessary, remember that our assistance service (organised in
collaboration with our dealers) is always available for advice or direct
intervention.
Intended use
The scrubbing machine is designed exclusively for the professional
cleaning of surfaces and floors in industrial, commercial and public
environments. The machine is only suitable for use in closed (or at least
covered) places.
The machine is not suitable for use in the rain, or under water jets. It is
FORBIDDEN to use the machine in places with a potentially explosive
atmosphere, for picking up dangerous dusts or inflammable liquids. In
addition, it is not suitable as a means of transport for people or objects.

55
TECHNICAL DESCRIPTION UM SCRUB 35C
Rated power W 500
Working width mm 335
Width of rear squeegee mm 525
Work capacity m2/h 1010
Water consumption g/m2-
Brushes (diameter / length) mm 110 / 335 - 330
Brush rotations rpm 450
Pressure on the brushes kg 14,5
Brush motor V / W 12 / 250
Type of advance semi-aut.
Maximum gradient 2%
Suction motor V / W 12 / 250
Suction vacuum mbar -
Solution tank PE l 10
Recovery tank PE l 10
Gross weight of the machine ready for use kg 69
Battery V/Ah 12 / 65
Battery charger V/
A
12/6
Battery compartment dimensions (Length / Height / Width) mm / mm / mm 277 / 224 / 172
Machine dimensions (Length / Height / Width) mm / mm / mm 718 / 1105 / 460
Length of the closed machine (without recovery tank) mm 928
Height of the closed machine (without recovery tank) mm 446
Noise level (in compliance with IEC 704/1) dB (A) 65,8
Vibration level m/s21,31

6 76 7
SYMBOLS USED ON THE MACHINE
Tap symbol
Used to indicate the solenoid valve switch
Brush symbol (BRUSHING VERSION)
Used to indicate the brush motor switch
Symbol denoting suction motor
Used to indicate the suction motor switch
Battery symbol
Battery charge level indicator
Indicates the maximum temperature of the detergent solution
Located near the solution tank inlet
Warning high voltage 110-220 Volt
Indicates the maximum gradient

77
GENERAL SAFETY REGULATIONS
The regulations below must be carefully followed in order to avoid harm to the operator and damage to
the machine.
Read the labels on the machine carefully. Do not cover them for any reason and replace them immediately
if they become damaged.
The machine must be used exclusively by authorised, trained personnel.
During the working of the machine, pay attention to other people and especially to children.
The machine is not suitable for cleaning carpets.
The socket for the battery charger cable must have a prescribed earth connection.
Avoid damaging the battery charger cable by crushing or bending it, or applying stress.
If you notice any damage to the battery charger cable, contact a ICE technical assistance centre
immediately.
Do not mix different types of detergent as this may produce harmful gases.
Do not place any liquid containers on the machine.
The machine is designed for dry use only and should not be used or kept outdoors in wet conditions
The storage temperature must be between -25C and +55C; do not store outdoors in damp conditions.
Conditions of use: room temperature between 0C and 40C with relative humidity between 30 and 95%.
Do not use the machine in an explosive atmosphere.
Do not use the machine as a means of transport.
Do not use acid solutions, which may damage the machine.
Avoid working with the brushes when the machine is standing still, so as not to damage the floor.
Do not vacuum inflammable liquids.
Do not use the device to collect dangerous powders.
In the event of a fire, use a powder extinguisher. Do not use water.
Do not knock against shelving or scaffolding, where there is a danger of falling objects.
If you use the machine where there is a risk of falling objects, the machine must be equipped with
protection devices against falling objects
Do not use the machine on surfaces with an inclination greater than the one shown on the plate.
The machine is designed to carry out the washing and drying operations simultaneously. Different
operations should only be carried out in areas where the passage of unauthorised persons is prohibited.
Signal the presence of damp floors with suitable signs.
If the machine does not work properly, check this is not caused by failure to carry out routine maintenance.
Otherwise, request the intervention of the ICE technical assistance centre.
If you need to replace any components, request the ORIGINAL spare parts from a ICE dealer and/or
Authorised Retailer.
Before carrying out any maintenance work, switch off the machine and disconnect the battery connector.
Do not remove any protection devices which require the use of tools in order to be removed.
Do not wash the machine with direct water jets or with pressurised water, nor with corrosive substances.
Have the machine checked by a ICE technical assistance centre every year.
To prevent the formation of scale in the solution tank filter, do not fill the tank with detergent solution many
hours before using the machine.
Before using the machine, check that all the hatches and covers are positioned as shown in this Use and
Maintenance Manual.
When disposing of consumption materials, observe the laws and regulations in force.
When your ICE machine has reached the end of its long working life, dispose of the materials it contains

8 98 9
(especially oils and electronic components) in an appropriate manner, and bearing in mind that the machine
itself was constructed using 100% recyclable materials.
Only use the brushes supplied with the device, or those specified in the Instructions Manual. The use of
other brushes could compromise safety levels
The device must be disconnected from the power supply before removing the battery.
The battery must be removed from the device before this is disposed of.
The battery and battery charger must be disposed of in a safe manner, scrupulously respecting the laws in
force.
The machine is not suitable for use by children or people with reduced physical, mental and sensorial
capacities, or people lacking experience and knowledge, unless supervised and instructed in the use of the
machine by a person responsible for their safety.
Children must be supervised to ensure they do not play with the device.

99
MACHINE PREPARATION
1. HANDLING THE PACKED MACHINE
The machine is contained in specific packaging.
Every pallet consists of four machines arranged on two levels.
It is not possible to place more than two packages on top of each other.
The total weight is 70kg
The overall dimensions of the package are:
A: 510mm
B: 490mm
C: 1020mm
2. HOW TO UNPACK THE MACHINE
1. Open the packaging on the side indicated.
2. Take the machine out of its packaging.
3. Remove the brushes.
4. Remove the recovery tank.
3. HANDLING AND TRANSPORTATION OF THE UNPACKED MACHINE
V
ispa 35BS is a machine that can be managed in all situations and transported without effort, even in
small vehicles.
Just lift the front part, using the machine handlebars as a lever. The big wheels and small rear wheels
mean it can be towed anywhere and loaded on a truck by means of a simple ramp.
V
ispa 35BS is easy to transport even by car. Taking advantage of the great flexibility of the handlebars,
you can fold it up (see “FIXING THE HANDLEBARS”) and, with the help of a colleague, put it in the boot
of the car.

10 1110 11
MACHINE PREPARATION
4. TYPE OF BATTERY
To power the machine it is necessary to use:
sealed traction batteries with gasrecombination or gel technology
OTHER TYPES MUST NOT BE USED.
The batteries must meet the requisites laid out in standards CEI EN 60254-1:2005-12 (CEI 21-5) +
CEI EN 60254-2:2008-06 (CEI 21-7).
Every battery consists of DIN-type elements connected in series and supplying 12 V power to the
clamps. You are advised to use batteries with an electric capacity of 65 Ah (C5).
5. BATTERY MAINTENANCE AND DISPOSAL
For maintenance and recharging, respect the instructions provided by the battery manufacturer.
Particular attention must be paid when choosing the battery charger, if not supplied, since there are
different kinds according to the type and capacity of the battery.
W
hen the battery reaches the end of its working life, it must be disconnected by expert, trained
personnel, then lifted (using the grips and suitable lifting devices) to remove it from the battery
compartment. EXHAUSTED BATTERIES ARE CLASSIFIED AS DANGEROUS WASTE AND MUST BE
CONSIGNED TO THE AUTHORISED BODIES FOR CORRECT DISPOSAL.
Proceed as follows when the battery is dead:
1. Disconnect the quick connector and remove the solution tank.
2. Open the battery compartment and disconnect the connector.
Remove the battery using suitable devices by lifting with the provided handles.
WARNING: you are advised to always wear protective gloves in order to avoid
the risk of serious injury to your hands
WARNING: You are advised to only lift and move the batteries with lifting and
transportation means suitable for the specific weight and size
6. INSERTING/CONNECTING THE BATTERIES
The machine is supplied with a built-in battery charger and an airtight gel battery. If you use batteries
other than those supplied with the machine, use only 12V AGM or Gel batteries and proceed as follows.
The batteries must be housed in the special compartment beneath the solution tank.
To insert the batteries you must:
1. Disconnect the quick connector (1) at the front of the solution tank in order to avoid breakage of the
connector itself
2. Remove the solution tank and place it on the ground 1