ICOP Technology IBW-35 User manual

ICOP Technology Inc.
User Manual
IBW-35
A 3.5” embedded solution on
Intel® Quad-core Processor
(Braswell Family)
Version 1.0

IBW35 User Manual
ICOP Technology Inc. I
Copyright
The information in this manual is subject to change without notice for continues
improvement in the product. All rights are reserved. The manufacturer assumes no reasonability
for any inaccuracies that may be contained in this document and makes no commitment to
update or to keep current the information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in
part, in any form or by any means without the prior to written permission of ICOP Technology
Inc.
Copyright ⓒ 2018 ICOP Technology Inc

IBW35 User Manual
ICOP Technology Inc. II
Revision History
Revision Date Remark
1.0 February 25, 2020 First version release

IBW35 User Manual
ICOP Technology Inc. III
Table of Contents
1 General Information ........................................................................................... 1
1.1 Overview ....................................................................................................................................... 1
1.2 Block diagram ................................................................................................................................ 1
1.3 Specifications ................................................................................................................................. 2
1.4 Ordering Information .................................................................................................................... 4
1.4.1 IBW-35 .................................................................................................................................... 4
1.4.2 Option Accessary ..................................................................................................................... 4
2 Hardware Information ....................................................................................... 5
2.1 Dimension ..................................................................................................................................... 5
2.2 Board Outline ................................................................................................................................ 6
2.3 Connector and Jumper Summary ................................................................................................... 7
2.4 Pin Assignments & Jumper Settings ............................................................................................... 9
J2: LPC Header ................................................................................................................................ 9
J8: VGA ........................................................................................................................................... 9
J10: Jumper Selection for AT/ATX ............................................................................................... 10
J11: Power for SATA HDD ........................................................................................................... 10
J12: SATA DOM ........................................................................................................................... 10
J14: SIM Card Holder .................................................................................................................... 11
J15: Line-in .................................................................................................................................... 11
J16: Line-out .................................................................................................................................. 11
J17: MIC-in .................................................................................................................................... 12
J18: I2C .......................................................................................................................................... 12
J23: Power Button .......................................................................................................................... 12
J24: Reset Button ........................................................................................................................... 13
J25: COM1 (RS232) ....................................................................................................................... 13

IBW35 User Manual
ICOP Technology Inc. IV
J26: COM2 (RS232) ....................................................................................................................... 14
J27: COM3 (RS232/422/485) ........................................................................................................ 14
J28: COM4 (RS232/422/485) ........................................................................................................ 15
J29: GPIO ...................................................................................................................................... 15
J30: USB(2.0) 1 ............................................................................................................................... 16
J32: Power Input ............................................................................................................................ 16
JINV1: Power Selection for INV1 .................................................................................................. 16
JVLCD1: Power Selection for LCD Panel ...................................................................................... 17
LVDS1: LVDS ............................................................................................................................... 17
INV1: LCD Backlight Control ....................................................................................................... 18
Technical Support Directly from ICOP ................................................................ 15
User Manual Feedback ............................................................................................. 15
Warranty ...................................................................................................................... 16

IBW35 User Manual
ICOP Technology Inc. 1
1 General Information
1.1 Overview
IBW35, a standard 3.5” embedded solution for industrial application based on Intel®
Braswell Quad-Core CPU with 4GB DDR3L RAM onboard, provides stable and powerful
computing performance.
IBW35 supports 2x Gigabit LAN, 4x COM, 6x USB, I2C, 16-bit GPIO, MiniPCIe,
HDMI, LVDS, VGA, and 3 storage options, storage as SATA interface, mSATA interface, and
Micro SD for development use. SIM card holder is also supported on IBW-35 for wireless
long-distance communication.
1.2 Block diagram

IBW35 User Manual
ICOP Technology Inc. 2
1.3 Specifications
Processor
Intel® AtomTM x5-E8000, 2.00Ghz (Burst), 1.04GHz Quad Core
Intel® Pentium® N3710, 2.56Ghz (Burst), 1.6GHz Quad Core (Option)
Intel® Celeron® N3160, 2.24Ghz (Burst), 1.6GHz Quad Core (Option)
System Memory 4GB DDR3L 1600MHz onboard
BIOS UEFI BIOS
Bus MiniPCIe (full-size) x1 SIM Card x1
Display
Hardware decoding: H.265, MPEG2, MVC, VC-1, VP8, WMV9, and JPEG/MJPEG formats
Hardware encoding: H.264, MVC, and JPEG/MJPEG formats
VGA: resolutions up to 1920 x 1200 @ 60Hz
HDMI: resolutions up to 2560 x 1600 @ 60Hz, 24bpp
LVDS: resolutions up to 1920 x 1200 @ 60Jz, in dual LVDS bus mode
LAN Realtek 8111H GbE x2
HD Audio Realtek ALC262 VD
Disk Support
Micro SD x1
SATA device x1
mSATA device x1*
I/O Interface
COM x4
I2C x1
USB3.0 x4
USB2.0 x2
16-bit GPIO x1
*mSATA interface could be configured as a standard MiniPCIe interface through H/W modification

IBW35 User Manual
ICOP Technology Inc. 3
Connectors
7-pin SATA connector for SATA DOM x1
4.2mm 4-pin wafer for Power x1
2.5mm 4-pin wafer for SATA HDD Power x1
2.0mm 20-pin box header for GPIO x1
2.0mm 14-pin header for LPC x1
2.0mm 10-pin box header for COM x2
2.0mm 2-pin wafer for Power button x1
2.0mm 2-pin wafer for Rest buttom x1
1.25mm 4-pin wader for Line-in/Line-out/MIC-in x3
1.25mm 4-pin wafer for I2C x1
1.25mm 30-pin wafer for LVDS x1
1.0mm 12-pin wafer for VGA x1
HDMI connector x1
Mini PCIe socket x2
RJ45 connector x2
USB3.0 connector x4
USB2.0 connector x2
SIM card holder x1
Power
Requirement 12V standard input from internal 4-pin power connector support for ATX mode
Operating Temp. 0°C to +60°C
Dimensions 102mm x 146mm
Weight 120g
O/S Support
Windows 10
Windows 7 (64bits)
Linux

IBW35 User Manual
ICOP Technology Inc. 4
1.4 Ordering Information
1.4.1 IBW-35
Product Name IBW-35-E4 IBW-35-A4 IBW-35-B4
Processor 1.04GHz
(Intel® AtomTM x5-E8000)
1.60GHz
(Intel® Pentium® N3710)
1.60GHz
(Intel® Celeron® N3160)
System Memory 4GB DDR3L 1600MHz
Accessary CABLE-SATA-IBW-15CM x1
1.4.2 Optional Accessary
CABLE-SET-IBW35 Cable set for IBW-35 (RS232 x4, GPIO x1, Audio x3)
CABLE-ATX12V-10CM ATX12V 2x2 Pin to DC power jack cable
CABLE-VGA-IBW35-15CM VGA cable for IBW-35

IBW35 User Manual
ICOP Technology Inc. 5
2 Hardware Information
2.1 Dimension

IBW35 User Manual
ICOP Technology Inc. 6
2.2 Board Outline
TOP:
BOTTOM:

IBW35 User Manual
ICOP Technology Inc. 7
2.3 Connector and Jumper Summary
Nbr. Name Type of Connections Nbr of Pin
J2 LPC Header Pin Header, 2.0m, 7x2 14
J3 Micro SD Slot Standard Micro SD Slot
J5 USB(3.0) 0 & 1 Type A USB3.0 Connector
J6 USB(3.0) 2 & 3 Type A USB3.0 Connector
J7 HDMI Standard HDMI Connector
J8 VGA Wafer, 1.0mm, 12x1 12
J9 mSATA Standard MiniPCIe connector
J10 Jumper Selection for AT/ATX Pin Header, 2.0mm, 2x2 4
J11 Power for SATA HDD Wafer, 2.5mm, 4x1 4
J12 SATA Connector SATA 7p Connector, 7x1 7
J14 SIM Card Holder Standard SIM Card Holder
J15 Line-in Wafer, 1.25mm, 4x1 4
J16 Line-out Wafer, 1.25mm, 4x1 4
J17 MIC-in Wafer, 1.25mm, 4x1 4
J18 I2C Wafer, 1.25mm, 4x1 4
J19
LAN1
RJ45 Connector 8
J19A LED-SMD
J19B LED-SMD
J20
LAN2
RJ45 Connector 8
J20A LED-SMD
J20B LED-SMD
J23 Power Button Wafer, 2.0mm, 2x1 2
J24 Reset Button Wafer, 2.0mm, 2x1 2
J25 COM1 (RS232) Box Header, 2.0mm, 5x2 10
J26 COM2 (RS232) Box Header, 2.0mm, 5x2 10
J27 COM3 (RS232/422/485) Box Header, 2.0mm, 5x2 10
J28 COM4 (RS232/422/485) Box Header, 2.0mm, 5x2 10
J29 GPIO Box Header, 2.0mm, 10x2 20
J30 USB(2.0) 1 Wafer, 1.25mm, 5x1 5
J31 USB(2.0) 2 Type A USB2.0 Connector
J32 Power Input Wafer, 4.2mm, 2x2 4
JINV1 Power Selection for INV1 Pin Header, 2.0m, 2x2 4
JVLCD1 Power Selection for LCD Panel Pin Header, 2.0mm, 2x3 6

IBW35 User Manual
ICOP Technology Inc. 8
LVDS1 LVDS Wafer, 1.25mm, 15x2 30
INV1 LCD Backlight Control Wafer, 2.0mm, 5x1 5
LED2 Wireless LED LED-SMD
LED3 SATA DOM LED LED-SMD

IBW35 User Manual
ICOP Technology Inc. 9
2.4 Pin Assignments & Jumper Settings
J2: LPC Header
Pin# Signal Name Pin# Signal Name
1. LPC_CLKOUT 2 GND
2 L_FRAME_N 4 NC
3 PLTRST_3P3_N 6 VCC5
7 LPC_AD3 8 LPC_AD2
9 VCC3 10 LPC_AD1
11 LCD_ADD 12 GND
13 LCD_SMB_CLK 14 LPC_SMB_DAT
J8: VGA
Pin# Signal Name
1. ROUT
2 GND
3 GOUT
4 GND
5 BOUT
6 GND
7 VGADDCSDA
8 GND
9 HSYNC_A
10 GND
11 VSYNC_A
12 VGADDCCLK

IBW35 User Manual
ICOP Technology Inc. 10
J10: Jumper Selection for AT/ATX
Pin 1&2 closed  AT mode
Pin 1&2 open  ATX mode
J11: Power for SATA HDD
Pin# Signal Name
1. VCC12
2 GND
3 GND
4 VCC5
J12: SATA DOM
Pin# Signal Name
1. GND
2 SATA_TXP
3 SATA_TXN
4 GND
5 SATA_RXN
6 SATA_RXP
7 GND

IBW35 User Manual
ICOP Technology Inc. 11
J14: SIM Card Holder
Pin# Signal Name
1. SIM-VCC
2 SIM-RST
3 SIM-CLK
4 GND
5 SIM-VPP
6 SIM-IO
J15: Line-in
Pin# Signal Name
1. LINE_IN_R
2 GND
3 LINE_IN_L
4 GND
J15: Line-out
Pin# Signal Name
1. LOUT_R
2 GND
3 LOUT_L
4 GND

IBW35 User Manual
ICOP Technology Inc. 12
J17: MIC-in
Pin# Signal Name
1. MIC_IN_R
2 GND
3 MIC_IN _L
4 GND
J18: I2C
Pin# Signal Name
1. GND
2 I2C5_SDA_3P3
3 I2C5_SCL_3P3
4 VCC3
J23: Power Button
Pin# Signal Name
1. PWRBTN
2 GND

IBW35 User Manual
ICOP Technology Inc. 13
J24: Reset Button
Pin# Signal Name
1. RSTBTN
2 GND
J25: COM1 (RS232)
Pin# Signal Name Pin# Signal Name
1. DCD1 2 RXD1
3 TXD1 4 DTR1
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1 10 VCC5

IBW35 User Manual
ICOP Technology Inc. 14
J26: COM2 (RS232)
Pin# Signal Name Pin# Signal Name
1. DCD2 2 RXD2
3 TXD2 4 DTR2
5 GND 6 DSR2
7 RTS2 8 CTS2
9 RI2 10 VCC5
J27: COM3 (RS232/422/485)
Pin# Signal Name Pin# Signal Name
1. DCD3/422TX-3
/1RS485-3 2 RXD3/422TX+3 /1RS485+3
3 TXD3/422RX+3 4 DTR3/422RX-3
5 GND 6 DSR3
7 RTS3 8 CTS3
9 RI3 10 VCC5

IBW35 User Manual
ICOP Technology Inc. 15
J28: COM4 (RS232/422/485)
Pin# Signal Name Pin# Signal Name
1. DCD4/422TX-4
/2RS485-4 2 RXD4/422TX+4 /2RS485+4
3 TXD4/422RX+4 4 DTR4/422RX-4
5 GND 6 DSR4
7 RTS4 8 CTS4
9 RI4 10 VCC5
J29: GPIO
Pin# Signal Name Pin# Signal Name
1. GND 2 VCC5
2 GP80 4 GP70
3 GP81 6 GP71
7 GP82 8 GP72
9 GP83 10 GP73
11 GP84 12 GP74
13 GP85 14 GP75
15 GP86 16 GP76
17 GP87 18 GP77
19 VCC5 20 P_PERROR-