Icop VSX-6118-V2 User manual
VSX-6118-V2
DM&P Vortex86SX 300MHz
Tiny CPU Module
with 4S/4USB/VGA/LCD/LAN/2GPIO
128MB DDR2 Onboard
User’s Manual
(Revision 1.2A)
Copyright
The information in this manual is subject to change without notice for continuous improvement in
the product. All rights are reserved. The manufacturer assumes no responsibility for any
inaccuracies that may be contained in this document. And makes no commitment to update or to
keep current the information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part,
in any form or by any means without the prior written permission of the ICOP Technology Inc..
Copyright 2007 ICOPTechnology Inc.
Manual No. IUM6118-V2000-01 Ver.1.0A September, 2009
Manual No. IUM6118-V2000-01 Ver.1.1A May, 2010
Manual No. IUM6118-V2000-01 Ver.1.2A October, 2010
Trademarks Acknowledgment
Vortex86SXis the registered trademark of ICOP Technology Inc.
Other brand names or product names appearing in this document are the properties
and registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.
T a b l e o f C o n t e n t s
T ab l e o f C o n t e n t s.............................................................iii
C h a p t e r 1 Introduction……………………………………………1
1.1 Packing List............................................................1
1.2 Product Description................................................2
1.3 Specifications.........................................................3
1.4 Board Dimension....................................................4
C h a p t e r 2 Installation……………………………………………..5
2.1 Board Outline.........................................................5
2.2 Connectors & Jumpers Location............................6
2.3 Connectors & Jumpers Summary...........................8
2.4 PinAssignments & Jumper Settings.......................9
2.5 System Mapping...................................................16
2.6 Watchdog Timer...................................................19
2.7 GPIO....................................................................20
2.8 SPI flash...............................................................21
C h a p t e r 3 Driver Installation……………………………………22
Appendix ………………………………………………………………..23
A. TFT Flat Panel Data Output......................................23
B. TFTFlat Panel Support List.......................................24
C. LVDS Flat Panel Support List....................................26
D. Flat Panel Wiring and Lighting..................................27
E. TCP/IPlibrary for DOS real mode.............................28
F. BIOS Default Setting..................................................29
Warranty............................................................................................30
Vortex86DX-6118-V2 Vortex86SXTiny CPU Module
1
C h a p t e r 1
Introduction
1.1 Packing List
Product Name Package
VSX-6118-V2
Embedded Vortex86SX CPU All-in-One Board
Manual & Drivers CD x 1
RS232 cable x 4
IDE cable x 1
USB cable x 2 (USB port x 2)
VGA cable x 1
GPIO cable x2
PS/2 Mouse cable x 1
PS/2 Keyboard cable x 1
Vortex86SX-6118-V2 Vortex86SXTiny CPU Module 2
1.2 Product Description
The VSX-6118-V2 family of low-power x86 embedded controller is designed to meet Tiny
specification, and integrated with the following features.
300MHz Vortex86SX System-On-Chip
128 / 256MB DDR2 system memory
VGA, TFTLCD support up to
1280x1024 resolution
Enhanced IDE
10/100Mbps Ethernet
4 USB 2.0 (host)
Up to 4 serial ports
16-bit GPIO x 2
Audio (Optional)
2 watchdog timer
JTAG interface
AMI BIOS
2MB SPI flash
Single voltage +5V DC
Support extended operating
temperature range of -20°C to +70°C
The VSX-6118-V2Tiny family of embedded controller is designed with backward compatibility in
mind, to provide migration path for projects facing end-of-life challenges with their existing x86
based Tiny controller.The VSX-6118-V2 family of controller is designed as a plug in
replacement, with backward compatibility to support legacy software to help extend existing
product life cycle without heavy re-engineering.
VSX-6118-V2 is suitable for broad range of data-acquisition, Industrial automation, Process
control,Automotive controller,AVL, Intelligent Vehicle management devic,Medical device,
Human machine interface, Robotics, machinery controlAnd more…application that required
small footprint, low-power and low-cost hardware with open industry standard such as Tiny.
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 3
1.3 Specifications
Features VSX-6118-V2
CPU DM&P SoC CPU Vortex86SX- 300MHz
Real Time Clock with Lithium Battery Backup
Cache L1:16K I-Cache, 16K D-Cache
BIOS AMI BIOS
System Memory 128/ 256MB DDR2 Onboard
Watchdog Timer Software programmable from 30.5 us to 512 seconds x2
sets(Watchdog 1 fully compatible with M6117D)
VGA XGI Volari Z9s Chipset
VGA and TFT Flat Panel Interface Support
LVDS Flat Panel Interface Support (Optional)
Onboard 32MB VGA Memory
Support resolution up to 1280 x 1024,16MB colors
LAN Integrated 10/100M Ethernet
Audio CM119 USB Audio controller (Optional)
I /O Interface Enhanced IDE port x1
RS-232 port x3
RS-232/485 port x1 (RS485 with Auto Direction)
USB port x4 (USB 2.0 version)
16-bit GPIO port x2
10/100Mbps Ethernet port x1
Connectors 2.00 mm 44-pin box header for IDE x1
2.00 mm 44-pin box header for LCD x 1
2.00 mm 10-pin box header for VGA x1
2.00 mm 20-pin box header for 16-bit GPIO x2
2.00 mm 10-pin box header for RS-232 x4
2.00 mm 10-pin box header for USB x2
2.00 mm 2-pin header for Console Redirection x1
2.54 mm 5-pin box header for keyboard x1
2.54 mm 5-pin header for Mouse x1
2.54 mm 2-pin header for Reset x1
1.25 mm 6-pin Wafer for JTAG x1
External RJ-45 connector for Ethernet x1
Flash Disk Support
Onboard 2MB SPI Flash Disk (Driver: A)
44-pin IDE Flash Disk( EmbedDisk 16MB or above)
Power Requirement Single Voltage +5V @ 600mA
Dimension 100mm X 66mm (3.94 x2.6 inches)
Weight 63g
Operating
Temperature -20oC ~ +70oC
-40°C ~ +85°C (Optional)
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 4
1.4 Board Dimension
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 5
C h a p t e r 2
Installation
2.1 Board Outline
(Note1: If you Enable 2M SPI flash Disk on the BIOS setting, you cannot use
GP30~GP37 Pins)
(Note2: If you Enable RS-232/485 on the BIOS setting, you cannot use
GP25~GP27 Pins)
(Note3: COM2 RS232/485 is selected by BIOS setting)
(Note4: Audio is optional)
(Note5: VSX-6118-V2-256 is optional)
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 6
2.2 Connectors & Jumpers Location
Connectors
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 7
Jumpers & LEDs
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 8
2.3 Connectors & Jumpers Summary
Summary Table
Nbr Description Type of Connections Pin
nbrs.
J1 IDE Box Header, 2.0,22x2 44-pin
J2 USB 2/ 3 Box Header,2.0, 5x2 10-pin
J4 10/100Base-TEthernet LAN RJ45 Connector 8-pin
J5 JTAG Wafer, 1.25, 6x1 6-pin
J8 PS/2 Keyboard Box Header, 2,54,1x5 5-pin
J9 Buzzer Pin Header, 2,54,1x2 2-pin
J10 PS/2 Mouse Pin Header, 2,54,1x5 5-pin
J11 COM1 Box Header, 2.05x2 10-pin
J12 COM2(RS232/RS485) Box Header, 2.05x2 10-pin
J13 GPIO ( Port 0 / 1 ) Box Header, 2.0,10x2 20-pin
J16 Reset Pin Header, 2,54,1x2 2-pin
J17 Power Connector Terminal Block 5.0,2x1 2-pin
J18 COM3 Box Header, 2.05x2 10-pin
J19 COM4 Box Header, 2.05x2 10-pin
J21 VGA Pin Header, 2.0,5x2 10-pin
J22 USB 0 / 1 Box Header,2.0, 5x2 10-pin
J23 GPIO ( Port 2 / 3) Box Header, 2.0,10x2 20-pin
J24 LCD Box Header, 2.0,22x2 44-pin
J25 LINE-OUT (Optional) Wafer, 1.25, 4x1 4-pin
J26 MIC-IN (Optional) Wafer, 1.25, 4x1 4-pin
J27 Console Redirection Pin Header, 2,54,1x2 2-pin
PWR-LED
PowerActive LED (Red) LED-SMD
IDE- LED IDEActive LED (Green ) LED-SMD
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 9
2.4 Pin Assignments & Jumper Settings
J1: IDE (44 Pins)
J2: USB 3 / 2
Pin # Signal Name
Pin # Signal Name
1 VCC 2 VCC
3 LUSBD3- 4 LUSBD2-
5 LUSBD3+ 6 LUSBD2+
7 GND 8 GND
9 GGND 10 GGND
Note
USB 3 will be occupied, while you use Audio.
Pin # Signal Name
Pin # Signal Name
1 IDERST 2 GND
3 IDED7 4 IDED8
5 IDED6 6 IDED9
7 IDED5 8 IDED10
9 IDED4 10 IDED11
11 IDED3 12 IDED12
13 IDED2 14 IDED13
15 IDED1 16 IDED14
17 IDED0 18 IDED15
19 GND 20 NC
21 IDEREQ 22 GND
23 IDEIOW 24 GND
25 IDEIOR 26 GND
27 ICHRDY 28 GND
29 IDEACK 30 GND
31 IDEINT 32 NC
33 IDESA1 34 IDECBLID
35 IDESA0 36 IDESA2
37 IDECS-0 38 IDECS1
39 IDELED 40 GND
41 VCC 42 VCC
43 GND 44 NC
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 10
J5: JTAG
Pin # Signal Name
Pin # Signal Name
1 VCC 2 GND
3 TCK 4 TDO
5 TDI 6 TMS
J8: PS/2 Keyboard
Pin # Signal Name
Pin # Signal Name
1 KBCLK 2 KBDAT
3 NC 4 GND
5 VCC
J9: Buzzer
Pin # Signal Name
Pin # Signal Name
1 Buzzer 2 VCC
J10: PS/2 Mouse
Pin # Signal Name
Pin # Signal Name
1 MSCLK 2 MSDATA
3 NC 4 GND
5 VCC
J11: COM 1 (Optional: TTL)
Pin # Signal
Name Pin # Signal
Name
1 DCD1 2 RXD1
3 TXD1 4 DTR1
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1 10 NC
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 11
J12: COM2 RS232 / RS485 (Optional: TTL)
Pin # Signal Name Pin #
Signal Name
1 DCD2/ RS485- 2 RXD2 / RS485+
3 TXD2 4 DTR2
5 GND 6 DSR2
7 RTS2 8 CTS2
9 RI2 10 NC
J13: GPIO (Port 0 / Port 1)
J16: RESET
Pin # Signal Name
Pin # Signal Name
1 Reset 2 GND
J17: Power Connector (Terminal Block 5.0mm)
Pin # Signal Name
1 +5V
2 GND
Pin # Signal Name
Pin # Signal Name
1 GND 2 VCC
3 GP00 4 GP10
5 GP01 6 GP11
7 GP02 8 GP12
9 GP03 10 GP13
11 GP04 12 GP14
13 GP05 14 GP15
15 GP06 16 GP16
17 GP07 18 GP17
19 VCC 20 GND
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 12
J18: COM3 (Optional: TTL)
Pin # Signal Name
Pin # Signal Name
1 DCD3 2 RXD3
3 TXD3 4 DTR3
5 GND 6 DSR3
7 RTS3 8 CTS3
9 RI3 10 NC
J19: COM4 (Optional: TTL)
Pin # Signal Name
Pin # Signal Name
1 DCD4 2 RXD4
3 TXD4 4 DTR4
5 GND 6 DSR4
7 RTS4 8 CTS4
9 RI4 10 NC
J21: VGA
Pin # Signal
Name Pin # Signal
Name
1 R OUT 2 GND
3 G OUT 4 GND
5 B OUT 6 GND
7 HSYNC 8 GND
9 VSYNCD 10 GND
J22: USB 0 / 1
Pin # Signal Name
Pin # Signal Name
1 VCC 2 VCC
3 LUSBD1- 4 LUSBD0-
5 LUSBD1+ 6 LUSBD0+
7 GND 8 GND
9 GGND 10 GGND
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 13
23: GPIO (Port 2 / Port 3)
Note:
If you Enable 2M SPI flash Disk on the BIOS setting, you cannot use GP30~GP37 Pins.
If you Enable RS-232/422/485 on the BIOS setting, you cannot use GP25~GP27 Pins.
Pin # Signal Name
Pin # Signal Name
1 GND 2 VCC
3 GP20 4 SPICS / GP30
5 GP21 6 SPICLK / GP31
7 GP22 8 SPID0 / GP32
9 GP23 10 SPIDI / GP33
11 GP24 12 GP34
13 GP25/RS232
14 GP35
15 GP26/RS422
16 GP36
17 GP27/RS485
18 GP37
19 VCC 20 GND
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 14
J24: LCD (DVO) Connector
Pin # Signal Name
Pin # Signal Name
1 +3.3V 2 +3.3V
3 LG2 4 LG3
5 LG4 6 LG5
7 NC 8 NC
9 LR0 10 LR1
11 LR2 12 LR3
13 LR4 14 LR5
15 GND 16 NC
17 NC 18 NC
19 NC 20 GND
21 NC 22 NC
23 LB0 24 LB1
25 LB2 26 LB3
27 LB4 28 LB5
29 NC 30 NC
31 LG0 32 LG1
33 GND 34 GND
35 NC 36 LCLK
37 NC 38 LDE
39 NC 40 LHSYNC
41 NC 42 LVSYNC
43 LBACKL 44 LVDDEN
(Please refer to Appendix A, for TFT Flat Panel Data Output)
J25: LINE OUT (Optional)
Pin # Signal Name
1 LOUTR
2 GND
3 GND
4 LOUTL
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 15
J26: MIC-IN (Optional)
Pin # Signal Name
1 MICVREF
2 GND
3 GND
4 MIC-IN
J27: Console Redirection (Pin 1 & Pin 2 short)
Pin # Signal Name
Pin # Signal Name
1 Console_Red
2 GND
Vortex86SX-6118-V2 Vortex86SXTinyCPUModule 16
2.5 System Mapping
Table of contents
Other Icop Controllers manuals
