ICP DAS USA HRT-310 User manual

HRT-310 Modbus RTU to HART Gateway - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 1
HRT-310
Modbus RTU to HART Gateway
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/hrt_310
Introduction
The HRT-310 is designed to be used as a master device of HART protocol, allowing the
Modbus to connect HART devices and converting the HART protocol to Modbus RTU / ASCII
protocol. In addition, the gateway is equipped with a more powerful built-in resistor, allowing
connecting up to 15 HART devices without having to connect an additional external resistor.
The HRT-310 is designed for users to integrate their HART devices into Modbus network easily
and quickly.
Figure1 : HRT-310 Application Structure
What’s In the Box
In addition to this guide, the package includes the following items:
HRT-310
CA-0910
Software CD
Screw Driver
(1C016)

HRT-310 Modbus RTU to HART Gateway - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 2
Pin Assignment
Pin
Name
Description
LP+
12
V+ of Loop Power (+24VDC)
HART+
11
Positive of HART
HART-
10
Negative of HART
+VS
23
V+ of Power Supply (+10 ~ +30 VDC)
GND
24
GND of Power Supply
RXD
18
Receive Data of RS-232
TXD
17
Transmit Data of RS-232
GND
19
GND of RS-232
RX+
15
Receive Data+ of RS-422
RX-
16
Receive Data- of RS-422
TX+
13
Transmit Data+ of RS-422
TX-
14
Transmit Data- of RS-422
D+
13
Data+ of RS-485
D-
14
Data- of RS-485

HRT-310 Modbus RTU to HART Gateway - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 3
P
e
t
t
h
e
d
i
P
l
e
a
s
e
s
e
t
t
h
e
d
i
p
D
I
DIP Switch Setting
Please set the dip switch of the “Resistor” and “Default” to be ”ON”
position.
Item
ON
Resistor
Enable HART loop resistor
(250 Ohm, 1W)
Default
Adapt the default settings.
(Refer to HART network wiring)



LED Indicator
LED
Status
Description
Name
PWR
ON
Module Power OK.
OFF
Module Power Failed.
ERR
Flash
HART Comm. Error.
OFF
HART Comm. OK
[ Flash per second ]
Module in initial mode.
Flash
[ Flash per half second ]
RUN
Module received the burst frame from
HART device.
ON
Module in normal operation.
OFF
Firmware has not been loaded yet.

HRT-310 Modbus RTU to HART Gateway - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 4


RS-232 Wiring
HART network wiring

HRT-310 Modbus RTU to HART Gateway - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 5
Install HG_Tool Utility
[ Install .NET Compact Framework ]
(1) When executing HG_Tool utility, the .NET Framework 2.0 or above
must be installed first. If the .NET Framework 2.0 or above exists in
the PC, please omit the step.
[ Install HG_Tool.exe ]
(1) Users can download the “HG_Tool” from the below source.
CD_Disk => CD:\hart\gateway\utilities\hg_tool\”
ftp://ftp.icpdas.com.tw/pub/cd/fieldbus_cd/hart/gateway/utilities/hg_tool/
(2) Execute the “setup.exe” file to install the “HG_Tool” utility.
(3) After finishing the installation of the HG_Tool, users can run the
utility. (refer to the path in the below figure)

HRT-310 Modbus RTU to HART Gateway - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 6
Communication Test
Step 1: Connect PC, HRT-310 and HART slave device according
to figure1.
Step 2: Set the DIP switch of the “Default” to be “ON” position.
Step 3: Turn on the power of HRT-310.
Step 4: Wait for the “RUN” LED to be always on status. If the “RUN” LED
always flashes, it means the HRT-310 can’t communicate with
the HART device. Please check the HART network wiring.
Step 5: Execute the HG_Tool utility.
Step 6: Set the communication settings between PC and HRT-310.
When the DIP switch of the “Default” to be “ON” position, the HRT-310
will adopt the below comport communication settings.
[1] Protocol: MB RTU
[2] Net ID: 1
[3] Baud Rate: 115200 bps
[4] Data Bits: 8
[5[ Stop Bits: 1
[6] Parity: None
=> So the HG_Tool must have the same settings with the HRT-310 as
shown in the below figure.

HRT-310 Modbus RTU to HART Gateway - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 7
Step 7: Click “Connect” button.
Step 8: Wait for the traffic light from red light to “green” light. If the
traffic light always keeps in the “yellow” light, it means the PC
can’t connect to HRT-710, please check the RS-232 wiring.
Step 9: Click the “Device Information” icon. Then select the “Default
CMD” or “User CMD” and right-click the mouse to choose
the “Basic Operation” option to get the information of the
corresponding HART command.
The information of HART command 0
Note
The detailed setting steps, please refer to the Q01 ~ Q03 of FAQ in the
manual.