ICP DAS USA EIP-2019 User manual

EIP-2019 8-Channel Thermocouple Analog Input EtherNet/IP Module
- QuickStart (Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
EIP-2019
Isolated 8-Channel Thermocouple Analog
Input EtherNet/IP Module
Quick Start Guide
1 What’s in the shipping package?
The package includes the following items:
EIP-2019
CD Quick Start Screw Driver CN-1824
(This document)
2 Installing Software on your PC
Install EIP-2000 Utility:
The software is located at:
Fieldbus_CD:\EtherNetIP\remote-io\EIP-2019\Utility

EIP-2019 8-Channel Thermocouple Analog Input EtherNet/IP Module
- QuickStart (Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3 Connecting the Power and PC
1. Make sure your PC has workable network settings.
2.
Disable or well configure your Windows firewall and anti-virus firewall first, else the
“Network Scan” on step 4 may not work. (Please contact with your system Administrator)
3.
Check FW/OP DIP switch if it is on OP position(Figure 3-1).
Figure 3-1 Mode Switch
4. Connect both the EIP-2000 and your computer to the same sub network or the same
Ethernet switch, and power the EIP-2000 on. Please refer to figure 3-2.

EIP-2019 8-Channel Thermocouple Analog Input EtherNet/IP Module
- QuickStart (Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

EIP-2019 8-Channel Thermocouple Analog Input EtherNet/IP Module
- QuickStart (Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
III. I/O Wire Connection
Voltage Input Thermocouple Input
4 Using the EIP-2000 Utility
1. Double click the “EIP-2000 Utility” shortcut on the desktop.
2. Click the “Network Scan” button to search your EIP-2000 modules(Figure 4-1).
Figure 4-1 EIP-2000 Utility network scan
3. Click the EIP-2019 or other EIP-2000 modules on the device list below to open the
configuration dialog of EIP-2000. Each EIP-2000 module has its own configuration
interface. Please refer to Figure 4-2.
(1) In the “Analog Input Status”, users can select AI type of every channel.
(2) In the “AI Parameters”, users can select the AI filters and AI representations here.
There are two different AI filters 50Hz and 60Hz. The selection of filters must
correspond with the frequency of AI sensors. Users have to check what are the
requirements of AI sensors. We provide two AI representations engineer and hex. If
users change the AI representation, all AI status will become to it.
(3) In “CJC Settings Users” can set the CJC enable or not by the CJC Switch, and adjust
CJC value with CJC Offset.
(4) If the network settings have been changed, please click the “Update Network
Settings” button to update the configuration and reboot the module.

EIP-2019 8-Channel Thermocouple Analog Input EtherNet/IP Module
- QuickStart (Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
(1)
(2)
(3)
(4)
Figure 4-2 EIP-2000 Utility configurations
4. Configuration settings of EIP-2000
Table 4-1 Network Settings
Network Settings
Item Settings (default)
IP
192.168.255.1
Gateway
192.168.0.1
Mask
255.255.0.0
For configuration of the Address Type, Static IP Address, Subnet Mask and Default Gateway of the EIP-2000. Please refer
to section “4.2.1 Network Settings”
Table 4-2 LED Indicator
LED Indicator
LED LED Status Description
Power LED
Alwa
y
s On Module is in Run mode.
Flashing Module is in Init mode.
Status LED
Alwa
y
s On EtherNet/IP connection is failed.
Blink
p
er secon
d
EtherNet/IP connection is successful.
Blink per 300 ms EtherNet/IP disconnected during communication but still in Safe-
Delay time.
Blink per 100 ms Module is about to reboot.
Error LED
On/Flashing AI status is close to full or out of range.
Of
f
AI status is within the range of input type.

EIP-2019 8-Channel Thermocouple Analog Input EtherNet/IP Module
- QuickStart (Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5 How to connect with Allen-Bradley PLC？
1. Open RSLogix 5000 and create a new project.
Figure5-1. Create a new project.
2. Select the PLC type and give the project a name.
Figure5-2. Set the PLC type and project name.

EIP-2019 8-Channel Thermocouple Analog Input EtherNet/IP Module
- QuickStart (Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3. Create a new module in the “Ethernet” item.
Figure 5-3. Create a new module.
4. Select the “ETHERNET-MODULE” below “Communications” in the
Select Module window.
7

EIP-2019 8-Channel Thermocouple Analog Input EtherNet/IP Module
- QuickStart (Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5. Configure the new module parameters. The I/O length of new module must be the same with
the length of EIP-2019 I/O data(Table 5-1). The input data size is 41 bytes and output data
size is 23 bytes. The instance ID please refer to Table 5-2.
Figure5-5. The settings of EIP-2019 module