ICP DAS USA ET-7000 series Instruction manual

Quick Start Manual
Version 1.02
Feb 2009

ET7000 Quick Start
Package checklist
The package includes the following items:
zOne ET-7000 hardware module
zOne Quick Start Manual
zOne software utility CD
zOne screw driver
Note:
If any of these items are missed or damaged, contact the
local distributors for more information. Save the shipping
materials and cartons in case you want to ship in the future.
Related documents and firmware
Documents
zUser Manual:
ET7000_User_Manual.pdf for Digital Output/Input modules
ET7K_AIO_User_Manual.pdf for Analog Input modules
zQuick Start Manual: ET7000_QuickStart_Manual.pdf
zLocation: CD: \NAPDOS\ET7000\Document
Firmware:
Location: CD: \NAPDOS\ET7000\Firmware
1

1. Preparation
View of the
Module
Ethernet Port
Connector J1
Connector J2
LED
Indicators
2

ET7000 Quick Start
3
Mounting the
ET-7000
Din-Rail Mounting
Snap the ET-7000 on to the DIN-rail
Snap the ET-7000 off from the DIN-rail

ET7000 Quick Start
Connecting
the ET-7000
into the
Ethernet
Link the ET-7000 and host PC direct or link the
ET-7000 into the same Ethernet as host PC.
Ethernet cable
Ethernet cable
4

ET7000 Quick Start
Apply power
to the
ET-7000
1. Check Init/Normal switch is on Normal position.
2. Apply power (+Vs, GND) to the ET-7000, +Vs
can be range from +10V to +30V DC.
3. Check that the L1 LED (“RUN”) periodically
ON for 0.5 seconds and then OFF for 0.5
seconds.
5

2. Ethernet Configuration
Configuring the network settings correctly is the most important
procedure prior to using ET-7000 controller. The following settings must
be configured:
Networking settings: IP, Mask, and Gateway of ET-7000.
Item Default
IP Address 192.168.255.1
Subnet Mask 255.255.0.0
Gateway 192.168.0.1
Installing MiniOS7 utility
The PC Diagnostic tool is located on the shipment CD and FTP. The
paths are
zCD:\ NAPDOS\ET7000\Tools\Tools for MiniOS7\MiniOS7_utility
zftp://ftp.icpdas.com/pub/cd/6000cd/napdos/et7000/tools/tools for
minios7/minios7_utility/
6

ET7000 Quick Start
Please follow the steps below:
1. Double Click the “Setup.exe” to start installing.
2. Click on “Next” when the Welcome window opens.
3. Click on “Next” to install program files in the default directory, or
select an alternative location by pressing “Browser…”.
4. Select the folder using in list of “Start Menu” >> “Program”>>, and
then click on “Next” to continue
5. Click on “Next” to proceed with the installation.
6. Click on “Finish” to complete the installation.
7

ET7000 Quick Start
Search -- Search the devices
1. Run the MiniOS7 utility as follow
2. Click the Search on the main menu to scan the modules on the
Ethernet network.
8

ET7000 Quick Start
3. The Search Progress will show on the bottom of the “MiniOS7 Scan”
windows. Users can press button to cancel the search.
3. Choose the found module in the table and Press button to
configure IP settings.
9

ET7000 Quick Start
4. The current settings of the module will show on the dialog below, and
the user can change the value on each item and then press the “Set”
button to take effect of the settings.
10
Click the “Set” button will cause the ET-7000 to
reboot to make the settings effectively.
5. Search again to check whether the settings have been changed or
not.

ET7000 Quick Start
11
3. Connect the ET-7000 -- by web browser
1. Start up the web browser (Internet Explorer, Mozilla or Firefox),
input the URL address of the ET-7000 (such as http://10.0.8.13)
and then press “Enter” key to link the ET-7000.
2. Input the User name and Password.
Web page Configuration
Item Default
User name Admin (Case sensitive)
Password Admin (Case sensitive)

ET7000 Quick Start
The brief description of the Web page configuration function is listed
on six main functions of the tree structure.
12

13
Technical Support
If you have problems about using the ET-7000 series modules, please
contact ICP DAS Product Support.
Email: [email protected]
When requesting technical support, be prepared to provide the following
information about your system:
1. Module name and serial number: The serial number can be found
printed on the barcode label attached to the cover of the module.
2. Firmware and OS version: See Overview on the web browser linked
to ET-7000 as showed as page 3.2 for getting the firmware/OS
version information.
3. Host configuration:
3-1. Host type: PC, PLC or other host device
3-2. Operating system (If needed)
3-3. Web browser tool (ex. IE, Firefox, Mozilla …) and version
4. If the problem is reproducible, please give full details describing the
procedure used to reproduce the problem.
5. Specific error messages displayed. If a dialog box with an error
message is displayed, please include the full text of the dialog box,
including the text in the title bar.
6. If the problem involves other programs or hardware devices, please
describe the details of the problem in full.
7. Any comments and suggestions related to the problem are welcome.
ICP DAS will reply to your request by email within three business days.
Feb 2009