ICP DAS USA ZT-20 IOG Series User manual

ZT‐20xx‐IOGSERIES
QuickStart
1 What’sintheShippingPackage?
The shipping package contains the following items:


2 PreparingtheDevice
1. Power Supply: +10 ~ +30 VDC
+Vs GND +Vs
GND
ANT‐124‐05QuickStart
ZT‐20xx‐IOGModule
If any of these items are missing or damaged, please contact your local
distributor for more information. Save the shipping materials and cartons in
case you need to ship the module in the future.
2. Install "ZT-2000 Configuration Utility" to configure the ZT-20xx-IOG device.
-http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/utility/
-CD: \\Napdos\ZigBee\ZT_Series\Utility
ICPDAS,ZT‐20xx‐IOGSERIESQuickStart,Version1.0.0Page1
Copyright©2016byICPDASCo.,Ltd.AllRightsReserved.

3 HardwareBasicSetting
1. Hardware Setting Interface

2. Basic Setting Parameters for Hardware
① DIP 1 : Module Initial Mode
For normal operation, set the DIP_1 to the RUN position.
For advanced setting, set the DIP_1 to the INIT position, then can do the
setting by software.
Trigger Mode DIP_1 Descriptions
RUN OFF
Pan ID = according to the software setting (Default: 0x0000)
RF Channel = set by the rotary switch
Node ID = set by the rotary switch
INIT ON
Software setting, via ZT-2550/ZT-2570/ZT-USBC remotely
Pan ID = 0x3FFF
RF Channel = set by the rotary switch
AES128 Pulse Init.
ZT-2043-IOG
ZT-2053-IOG
ZT-2055-IOG
RF Channel Node ID Reserved
12345678910 11 12
ON
Init. Run
LevelPulse
DisableAES128
ZT-2060-IOG
ICPDAS,ZT‐20xx‐IOGSERIESQuickStart,Version1.0.0Page2
Copyright©2016byICPDASCo.,Ltd.AllRightsReserved.

ICPDAS,ZT‐20xx‐IOGSERIESQuickStart,Version1.0.0Page3
Copyright©2016byICPDASCo.,Ltd.AllRightsReserved.
② DIP 2 : DI Event trigger mode or way
The event trigger modes of the ZT-IOG system, the same are the trigger ways for
the DI channel of the ZT-IOG module. Users is able to choose the suitable mode
via refering user manual for detail descriptions.
Trigger Mode DIP_2 Descriptions
Level Mode OFF If any DI channel state is high, all DO channel states are high.
If all DI channel states are low, all DO channel states are low.
Pulse Mode ON If any DI channel is triggered to rising edge, all DO channels will
change to the reverse edge once.
③ DIP 3 : Encryption
In wireless communication, it provides data encryption that supports AES-128 bit
encryption algorithm. This setting is based on the ZigBee Coordinator, other
ZT-IOG modules within the same group are synchronized passively.
Encryption DIP_3 Descriptions
Disable OFF Not using encryption
Enable ON Using AES-128 bit encryption for wireless communications
④ DIP 4~8 : Node ID
The Node ID is the ZigBee device ID, or known as the node addresses.
The settable range is 0x0000 ~ 0x001F, up to 32 groups, cannot duplicate in
the same group
A ZT-IOG network must specify a device to 0x0000 (ZigBee Coordinator)
The ZigBee Coordinator must be supplied power permanently, or the IOG
system cannot work properly.

Node ID DIP_4 DIP_5 DIP_6 DIP_7 DIP_8 Node ID DIP_4 DIP_5 DIP_6 DIP_7 DIP_8
0x0000 off off off off off 0x0010 ON off off off off
0x0001 off off off off ON 0x0011 ON off off off ON
0x0002 off off off ON off 0x0012 ON off off ON off
0x0003 off off off ON ON 0x0013 ON off off ON ON
0x0004 off off ON off off 0x0014 ON off ON off off
0x0005 off off ON off ON 0x0015 ON off ON off ON
0x0006 off off ON ON off 0x0016 ON off ON ON off
0x0007 off off ON ON ON 0x0017 ON off ON ON ON
0x0008 off ON off off off 0x0018 ON ON off off off
0x0009 off ON off off ON 0x0019 ON ON off off ON
0x000A off ON off ON off 0x001A ON ON off ON off
0x000B off ON off ON ON 0x001B ON ON off ON ON
0x000C off ON ON off off 0x001C ON ON ON off off
0x000D off ON ON off ON 0x001D ON ON ON off ON
0x000E off ON ON ON off 0x001E ON ON ON ON off
0x000F off ON ON ON ON 0x001F ON ON ON ON ON
⑤ Rotary Switch：RF Channel
“RF Channel” indicates the radio frequency channel, following the IEEE 802.15.4
standard and using the ISM 2.4G radio band.
Switch Range DescriptionRotary
Switch 0 ~ F 2405 MHz ~ 2480 MHz
a. The RF Channel must be set to the same value as other modules on the
same ZigBee network.
b. For different ZigBee networks, first priority is to adjust the RF Channel,
please directly switch the Rotary Switch.

The 2.4GHz is a universal free-of-use band, such as wireless LAN, Bluetooth, ZigBee, etc., all
can work in the 2.4GHz, so the user have better avoid to use the same wireless frequency with
other devices in the same
p
lace to ensure the communication effectiveness.
Announce ！

ICPDAS,ZT‐20xx‐IOGSERIESQuickStart,Version1.0.0Page4
Copyright©2016byICPDASCo.,Ltd.AllRightsReserved.

4 SoftwareAdvancedSetting
1. Advanced Setting Parameters for Software
The following items are the main functions and configurations to the software
advanced setting, please refer the user manual for more information.
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/document/zt-iog/
-Disconnection Detection : Safe Value (Router), Check-Router-Alive (Coordinator)
-I/O Channel Pair Relationship : Channel Offset (DI/DO)
-Other Parameters : Pan ID, RF Power, Refresh Interval
2. Software Setting Steps
The following steps are used to start the advanced setting via software.
①As the ZT-20xx-IOG device does not include a COM port, the user must
prepare a ZigBee converter, e.g. ZT-USBC, ZT-2550 or ZT-2570, to convert
the signal to wireless signal via the USB, RS-232 or RS-485 interface for
remote setting the ZT-20xx-IOG module.
②For building the wireless communication of the ZT-20xx-IOG and the
ZigBee converter, first, set up the following parameters of the ZigBee
converter via the "ZT-2000 Configuration Utility", so it can wirelessly
communicate with the ZT-20xx-IOG that in the INIT mode.
Model ZT-20xx-IOG ZT-USBC ZT-2550, ZT-2570
Application Mode N/A N/A Transparent Mode
Pan ID INIT default to 0x3FFF Set to 0x3FFF by software
Node ID INIT default to 0x0020 Fixed to 0x0000 as a ZigBee Coordinator
RF Channel Set by Rotary switch Same with the Rotary switch of the ZT-IOG.
③Switch the Dip Switch 1 (DIP_1) of the ZT-20xx-IOG module to INIT mode.
④Restart the power of the ZigBee Converter and the ZT-20xx-IOG module,
wait for the green LED (ZigBee) of the ZT-20xx-IOG module changing to
steady lit, that means the wireless communication established, and then
ICPDAS,ZT‐20xx‐IOGSERIESQuickStart,Version1.0.0Page5
Copyright©2016byICPDASCo.,Ltd.AllRightsReserved.

ICPDAS,ZT‐20xx‐IOGSERIESQuickStart,Version1.0.0Page6
Copyright©2016byICPDASCo.,Ltd.AllRightsReserved.
can call the software utility.
⑤Execute the ZT-20xx-IOG Configuration Utility (Windows Based):
⑥Use “ZT-IOG Series Configuration Utility” to connect the ZT-20xx-IOG.
a. Click【COM Port Setting】to select the COM port of the ZigBee converter.
b. Click【Read Setting】to read the current settings of the ZT-20xx-IOG module.
⑦After reading the settings, directly set the parameters in “New” column.
The next section will describe the parameters of the advanced setting.
⑧After setting the parameters, click【Start Configure】to complete the
software setting.

5 WiringConnection
Model Input Type ON State Readback as 1 OFF State Readback as 0
Relay ON Relay OFF
Dry Contact
Voltage > 3.5 V Voltage < 1 V
Wet Contact
(Source)
Open Collector ON Open Collector OFF
ZT-2053-IOG
Wet Contact
(Sink)
Close to GND Open
Dry Contact
+10 ~ +50 VDC +4 VDC Max.
Wet Contact
(Source)
+10 ~ +50 VDC +4 VDC Max.
ZT-2055-IOG
Wet Contact
(Sink)
+3.5 ~ +30 VDC OPEN or <1 VDC
Wet Contact
(Sink)
+3.5 ~ +30 VDC OPEN or <1 VDC
ZT-2060-IOG
Wet Contact
(Source)
ICPDAS,ZT‐20xx‐IOGSERIESQuickStart,Version1.0.0Page7
Copyright©2016byICPDASCo.,Ltd.AllRightsReserved.

ICPDAS,ZT‐20xx‐IOGSERIESQuickStart,Version1.0.0Page8
Copyright©2016byICPDASCo.,Ltd.AllRightsReserved.
Model Output
Type ON State Readback as 1 OFF State Readback as 0
Drive Relay

ZT-2043-IOG
Resistance
Load 
Resistance
Load
ZT-2055-IOG
Inductive
Load
ZT-2060-IOG
Relay
Output
6 Troubleshooting
If you have any difficulties using your ZT-20xx-IOG series I/O device, please send
the following contents of the problem to [email protected]
① Description of the problem
② Architecture of application, such as model name, number and
connection relationship.
③ The details of module configurations, such as the status of DIP switches,
rotary switch and software configurations.