ICP DAS USA Network Device I-7011 User manual

1
I-7011, I-7018 User ManualRev:B1.0
Warranty
All products manufactured by ICP DAS are warranted
against defective materials for a period of one year from the date
of delivery to the original purchaser.
Warning
ICP DAS assume no liability for damages consequent to
the use of this product. ICPDAS reserves the right to change this
manual at any time without notice. The information furnished by
ICPDAS is believed to be accurate and reliable. However, no re-
sponsibilityis assumedby ICPDASforits use,nor forany infringe-
ments of patents or other rights of third parties resulting from its
use.
Copyright
Copyright 1999 by ICPDAS.All rights are reserved.
Trademark
The names used for identification only maybe registered
trademarks of their respective companies.
I-7011/11D, I-7011P/11PD,
I-7018, I-7018P
User Manual
Date:1999-10

2
I-7011, I-7018 User Manual Rev:B1.0
Table of Contents
1.Introduction .....................................................5
1.1 More Information.......................................5
1.2 Pin Assignment ..........................................6
1.3 Specifications ............................................8
1.4 Block Diagram.........................................11
1.5 Wire Connection......................................12
1.6 Quick Start ..............................................14
1.7 Default Setting.........................................14
1.8 Jumper Setting.........................................14
1.9 Calibration...............................................15
1.10 Configuration Tables .............................16
2.Command.......................................................20
2.1 %AANNTTCCFF ...................................22
2.2 #** ...........................................................23
2.3 #AA .........................................................24
2.4 #AAN ......................................................25
2.5 $AA0 .......................................................26
2.6 $AA1 .......................................................27
2.7 $AA2 .......................................................28
2.8 $AA3 .......................................................29
2.9 $AA4 .......................................................30
2.10 $AA5VV ...............................................31

3
I-7011, I-7018 User ManualRev:B1.0
2.11 $AA6 .....................................................32
2.12 $AA8 .....................................................33
2.13 $AA8V ..................................................34
2.14 $AA9(Data)...........................................35
2.15 $AAB ....................................................36
2.16 $AAF.....................................................37
2.17 $AAM....................................................38
2.18 $AAZ(Data) ..........................................39
2.19 ~AAO(Data)..........................................40
2.20 ~AAEV..................................................41
2.21 @AADI..................................................42
2.22 @AADO(Data)......................................44
2.23 @AAEAT ..............................................45
2.24 @AAHI(Data) .......................................46
2.25 @AALO(Data)......................................47
2.26 @AADA................................................48
2.27 @AACA................................................49
2.28 @AARH................................................50
2.29 @AARL ................................................51
2.30 @AARE ................................................52
2.31 @AACE ................................................53
2.32 ~**.........................................................54
2.33 ~AA0.....................................................55
2.34 ~AA1.....................................................56

4
I-7011, I-7018 User Manual Rev:B1.0
2.35 ~AA2.....................................................57
2.36 ~AA3EVV.............................................58
2.37 ~AA4.....................................................59
2.38 ~AA5PPSS............................................60
3.ApplicationNote ............................................61
3.1 INIT* pin Operation ................................61
3.2 Module Status..........................................61
3.3 Dual Watchdog Operation .......................62
3.4 Digital Input and Event Counter..............62
3.5 Digital Output..........................................62
3.6 High/Low Alarm......................................63
3.7 Thermocouple Measurement ...................63

5
I-7011, I-7018 User ManualRev:B1.0
1. Introduction
I-7000 is a family of network data acquisition and control
modules. They provide analog-to-digital, digital-to-analog, digital
input/output, timer/counter and other functions. These modules can
be remote controlled by a set of commands. The common features
of I-7011/11D/11P/11PD/18/18P are given as following :
z3000VDC Isolated analog input
z24-bits sigma-delta ADC to provide excellent accuracy
zThermocouple direct connect with build-in CJC
zSoftware calibration
The I-7011 is a single channel analog input module. The I-
7011Dis the I-7011 witha4½ digitLEDdisplay. The I-7018 is a 8-
channel analog input module. The I-7011P/11PD/18P is the en-
hanced version of I-7011/11D/18. The I-7011P/11PD/18P support
more thermocouple types and enhanced the measure range of some
types.
1.1 More Information
Refer to “I-7000 Bus ConverterUserManual” chapter 1
for more information as following:
1.1 I-7000 Overview
1.2 I-7000 RelatedDocumentation
1.3 I-7000 Command Features
1.4 I-7000 SystemNetwork Configuration
1.5 I-7000Dimension

6
I-7011, I-7018 User Manual Rev:B1.0
1.2 PinAssignment

7
I-7011, I-7018 User ManualRev:B1.0

8
I-7011, I-7018 User Manual Rev:B1.0
1.3 Specifications
I-7011/I-7011D
Analog Input
Input Channel : 1
Input Type :
mV, V, mA(with external
125 ohms resistor)
Thermocouple : Type J, K,
T, E, R, S, B, N, C
Sampling Rate :
10 Samples/Second
Bandwidth : 5.24 Hz
Accuracy : ±0.05%
ZeroDrift : 0.5µV/°C
SpanDrift : 25ppm/°C
CMR@50/60Hz : 150dB
NMR@50/60Hz : 100dB
Input Impedance : 20M Ohms
Isolation : 3000VDC
Digital Output
2 channel
Open Collector to 30V
Output Load : sink 30mA max
PowerDissipation : 300mW
Digital Input
1 channel
Logic Level 0 : +1V max
Logic Level 1 : +3.5 to 30V
Event Counter
Max Input Frequency : 50 Hz
Min. Pulse Width : 1 mS
Displayed LED
4½ digits (for I-7011D)
Power Supply
Input : +10 to +30 VDC
Consumption :
0.9W for I-7011
1.5W for I-7011D

9
I-7011, I-7018 User ManualRev:B1.0
I-7011P/I-7011PD
Analog Input
Input Channel : 1
Input Type :
mV, V, mA(with external
125 ohms resistor)
Thermocouple : Type J, K,
T, E, R, S, B, N, C, L, M
Sampling Rate :
10 Samples/Second
Bandwidth : 5.24 Hz
Accuracy : ±0.05%
ZeroDrift : 0.5µV/°C
SpanDrift : 25ppm/°C
CMR@50/60Hz : 150dB
NMR@50/60Hz : 100dB
Input Impedance : 20M Ohms
Isolation : 3000VDC
Digital Output
2 channel
Open Collector to 30V
Output Load : sink 30mA max
PowerDissipation : 300mW
Digital Input
1 channel
Logic Level 0 : +1V max
Logic Level 1 : +3.5 to 30V
Event Counter
Max Input Frequency : 50 Hz
Min. Pulse Width : 1 mS
Displayed LED
4½ digits (for I-7011PD)
Power Supply
Input : +10 to +30 VDC
Consumption :
0.9W for I-7011P
1.5W for I-7011PD

10
I-7011, I-7018 User Manual Rev:B1.0
I-7018
Analog Input
Input Channel :
8 differential or 6 differen-
tial and 2 single-ended.
Jumper select.
Input Type :
mV, V, mA(with external
125 ohms resistor)
Thermocouple : Type J, K,
T, E, R, S, B, N, C
Sampling Rate :
10 Samples/Second
Bandwidth : 15.7 Hz
Accuracy : ±0.1%
ZeroDrift : 0.5µV/°C
SpanDrift : 25ppm/°C
CMR@50/60Hz : 150dB
NMR@50/60Hz : 100dB
Input Impedance : 20M Ohms
Overvoltage Protection : ±35V
Isolation : 3000VDC
Power Supply
Input : +10 to +30 VDC
Consumption : 1.0W
I-7018P
Analog Input
Input Channel :
8 differential or 6 differen-
tial and 2 single-ended.
Jumper select.
Analog Input Type :
mV, V, mA(with external
125 ohms resistor)
Thermocouple : Type J, K,
T, E, R, S, B, N, C, L, M
Sampling Rate :
10 Samples/Second
Bandwidth : 15.7 Hz
Accuracy : ±0.1%
ZeroDrift : 0.5µV/°C
SpanDrift : 25ppm/°C
CMR@50/60Hz : 150dB
NMR@50/60Hz : 100dB
Input Impedance : 20M Ohms
Overvoltage Protection : ±35V
Isolation : 3000VDC
Power Supply
Input : +10 to +30 VDC
Consumption : 1.0W

11
I-7011, I-7018 User ManualRev:B1.0
1.4 Block Diagram

12
I-7011, I-7018 User Manual Rev:B1.0
I-7018/18PAnalog Input Chan-
nel 0 to 5 Wire Connection
1.5WireConnection
I-7011/11D/11P/11PD Analog
Input Wire Connection
I-7011/11D/11P/11PD Digital
Input Wire Connection
I-7011/11D/11P/11PD Digital
Output Wire Connection

13
I-7011, I-7018 User ManualRev:B1.0
I-7018/18PAnalog Input Chan-
nel 6 and 7 Wire Connection,
whilethe jumperJP1 setting is8
differential mode.
I-7018/18PAnalog Input Chan-
nel 6 and 7 Wire Connection,
while the jumper JP1 setting is
INIT* mode.

14
I-7011, I-7018 User Manual Rev:B1.0
1.6 Quick Start
Refer to “I-7000BusConverterUserManual” and “Get-
ting Start” for more detail.
1.7Default Setting
Default setting for I-7011/11D/11P/11PD/18/18P :
zAddress : 01
zAnalog Input Type : Type 05, -2.5 to +2.5 V
zBaudrate : 9600 bps
zChecksum disable, 60Hz rejection, engineer unit format
zI-7018/18P set as INIT* mode, and the analog input is 6 dif-
ferential and 2 single-ended.
1.8 Jumper Setting
I-7018/18P : Jumper JP1 for select the pin INIT*/Vin 7-
Select 8 differential mode, the pin INIT*/Vin7- is set to Vin7-
Select INIT* mode, the pin INIT*/Vin7- is set to INIT*

15
I-7011, I-7018 User ManualRev:B1.0
1.9Calibration
Don’t Perform Calibrate Until You Really Understand.
Calibration Requirement for I-7011/11D/11P/11PD/18/18P
Notification :
1 While calibrate type 06, need connect external shunt resistor,
125 ohms, 0.1% (Ref Sec.1.5).
2 Connect calibration voltage(or current) signal to module’s
input. For I-7018/18P, connect to channel 0. (Wire connect ref
Sec.1.5)
3 Beforecalibration,warm-up module about 30minutes forbet-
ter accuracy.
Example Calibration Sequence for Type 00 :
1 Setting Type to 00 -> Ref
Sec.2.1.
2 Enable Calibration -> Ref
Sec.2.20.
3 Apply Zero CalibrationVoltage (0mV)
4 Preform Zero Calibration Command -> Ref Sec.2.6.
5 Apply Span Calibration Voltage (15mV)
6 Perform Span Calibration Command -> Ref Sec.2.5.
7 Repeat step1 to step6 three times.
Calibration sequence for other type is similiar but different in step
1 to set different type.
Type Code 00 01 02 03 04 05 06
Min. Input 0 mV 0 mV 0 mV 0 mV 0 V 0 V 0 mA
Max Input +15
mV +50 mV +100 mV +500 mV +1 V +2.5 V +20 mA

16
I-7011, I-7018 User Manual Rev:B1.0
1.10 ConfigurationTables
Configuration Table of I-7011/11D/11P/11PD/18/18P :
Baudrate Setting (CC)
Analog Input Type Setting (TT)
T.C Type L and M for I-7011P/11PD/18P only.
Data Format Setting (FF)
*1 : Filter Select : 0 = 60Hz rejection
1 = 50Hz rejection
*2 : Checksum Bit : 0=Disable, 1=Enable
*3 : 00 = Engineer Unit Format
01 = Percent Format
10 = 2’s Complement HEX Format

17
I-7011, I-7018 User ManualRev:B1.0
Type
Code Input Range Data Format +F.S. Zero -F.S.
00 -15 to +15
mV
Engineer Unit +15.000 +00.000 -15.000
% of FSR +100.00 +000.00 -100.00
2's complement HEX 7FFF 0000 8000
01 -50 to +50
mV
Engineer Unit +50.000 +00.000 -50.000
% of FSR +100.00 +000.00 -100.00
2's complement HEX 7FFF 0000 8000
02 -100 to +100
mV
Engineer Unit +100.00 +000.00 -100.00
% of FSR +100.00 +000.00 -100.00
2's complement HEX 7FFF 0000 8000
03 -500 to +500
mV
Engineer Unit +500.00 +000.00 -500.00
% of FSR +100.00 +000.00 -100.00
2's complement HEX 7FFF 0000 8000
04 -1 to +1 V
Engineer Unit +1.0000 +0.0000 -1.0000
% of FSR +100 00 +000 00 -100 00
Analog input type and data format table

18
I-7011, I-7018 User Manual Rev:B1.0

19
I-7011, I-7018 User ManualRev:B1.0
Type
Code Input Range Data Format +F.S. Zero -F.S.
16 C Type 0 to 2320
degree Celsius
Engineer Unit +2320.0 +00.000 +00.000
% of FSR +100.00 +000.00 +000.00
2's complement HEX 7FFF 0000 0000
17*1 L Type
-200 to 800
degree Celsius
Engineer Unit +800.00 +00.000 -200.00
% of FSR +100.00 +000.00 -025.00
2's complement HEX 7FFF 0000 E000
18*1 M Type
-200 to 100
degree Celsius
Engineer Unit +100.00 +000.00 -200.00
% of FSR +050.00 +000.00 -100.00
2's complement HEX 4000 0000 8000
*1 : Only available for I-7011P, I-7011PD and I-7018P

20
I-7011, I-7018 User Manual Rev:B1.0
2. Command
Command Format : (Leading)(Address)(Command)[CHK](cr)
Response Format : (Leading)(Address)(Data)[CHK](cr)
[CHK] 2-character checksum
(cr) end-of-command character, character return(0x0D)