ICPDAS TPD-283-H User manual

Technical support: servic[email protected] P1
TPD-283-H/283U-H
Quick Start
v1.1, Jan. 2019
What’s in the box?
Related Information
Thanks for buying ICPDAS TPD 2.8 inch H series device. This
shipping package contains the following items:
TPD-283-H/283U-H x 1
Quick Start x 1 (This Document)
If you are new to TPD-283-H/283U-H, please read the “Chapter 3.
Getting Started”
of the TouchPAD Hardware User Manual
for
detailed information about install the free development tool –
HMIWorks and how to create your first project.
Documents, such as the User Manuals, the API References,
etc.: http://ftp.icpdas.com/pub/cd/touchpad/document/
Free Development Software, HMIWorks v2.10.10 or above:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email.

Technical support: servic[email protected] P2
1 Appearance
Front View
TPD-283U-H Rear View TPD-283-H Rear View
2 Pin Assignments
On the back of the TPD-283U-H
No
Pin
Description
0
F.G.
Frame Ground. F.G. is connected to the inside EMI or
ESD suppression circuits. Make sure that F.G. is
connected to the Earth
1
VDC
DC input Voltage (range: +12 V ~ +48 V)
2
GND
Connected to the power supply’s ground pin
3
Data+
The positive data line of the RS-485 network
4
Data-
The negative data line of the RS-485 network
2.8”TFT LCD with Touch Panel
USB
Rotary Switch
RS-485
Ethernet
Rotary Switch
Ethernet

Technical support: servic[email protected] P3
3 Rotary Switch & Default Settings
The definition of the rotary switch (TPD-283-H):
No
Mode
Description
0
Run &
Update
This is a special run mode which is used in
the development stage. The TouchPAD
device can be updated by a PC from the
remote side through Ethernet. (Default)
1
Force
Update
While the application run on the TouchPAD
device seriously crashes, use this mode to
update a new application to the TouchPAD
device through Ethernet.
2
Run Only
Run the program.
The definition of the rotary switch (TPD-283U-H):
No
Mode
Description
0
Run &
Update
(Ethernet)
This is a special run mode which is used in
the development stage. The TouchPAD
device can be updated by a PC from the
remote side through Ethernet. (Default)
1
Ethernet
Force
Update
While the application run on the TouchPAD
device seriously crashes, use this mode to
update a new application to the TouchPAD
device through Ethernet.
2
Run Only
Run the program.
9
USB Force
Update
Update a new application to the TouchPAD
device through USB.
Network Default Settings
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1

Technical support: servic[email protected] P4
4 First Use of the TPD 2.8” H Series
1. Connect wires as the figure or prepare an
Ethernet cable which will be used to supply
power through PoE if there’s a RJ-45 Ethernet
port on it. And set the rotary switch to 0 (At this
point, the power is not yet supplied).
2. Supply power to the TPD-283-H/283U-H, wait for
several seconds and then you can see the default
program run on it.
3. Try to touch on the icons on the bottom-right corner
of the screen of the TPD-283-H/283U-H and you can
find that TPD-283-H/283U-H switches to the setting
pages.
5 Hardware Installation
PoE Switch
Use a flat-head screwdriver to set rotary switch
External Wall Box, EWB-T28 (optional)
Outlet Box, OB120 (optional)
External Power
GND
VDC (+12-+48 V)

Technical support: servic[email protected] P5
TPD-283-H/283U-H 快速入門指南
v1.1, 2019年1月
檢查配件
參考資訊
感謝您購買泓格的
TPD 2.8
吋
H
系列產品。產品包裝內應包含下列配
件:
TPD-283-H/283U-H x 1
產品須知 x 1 (本文件)
如果您是第一次使用
TPD-283-H/283U-H，請參閱 TouchPAD 硬體
使用手冊的
“第3 章啟動 TouchPAD” 來了解如何安裝免費的開發
軟體
HMIWorks 並建立第一個專案以及更多詳細的相關資訊。
相關文件，如使用手冊、應用程式介面指南(API Reference) 等:
http://ftp.icpdas.com/pub/cd/touchpad/document/
免費開發軟體，HMIWorks 版本 2.10.10 或以上版本:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
如有任何問題歡迎使用
E-mail
聯繫我們，我們將會為您提供完善的咨
詢服務。

Technical support: servic[email protected] P6
1 外觀
前配置圖
TPD-283U-H 後配置圖 TPD-283-H 後配置圖
2 腳位定義
在TPD-283U-H 的背面可見到如右圖樣
No
Pin
說明
0
F.G.
機架接地，F.G. (連接到內部的 EMI 或ESD 保護電路)，
請接到大地
1
VDC
直流電壓輸入 (範圍：+12 V ~ +48 V)
2
GND
連到電源的接地端
3
Data+
RS-485 網路的正訊號線
4
Data-
RS-485 網路的負訊號線
2.8 吋觸控液晶螢幕
USB
旋轉開關
RS-485
Ethernet
旋轉開關
Ethernet

Technical support: servic[email protected] P7
3 旋轉開關及出廠預設值
TPD-283-H 旋轉開關的配置模式定義:
No
模式
說明
0
Run & Update
執行/更新程式，用於程式開發階段 (能
執行程式，也能進行更新)。(出廠預設)
1
Force Update
強制更新，當 TouchPAD 上的程式嚴
重毀損時可用此模式透過 Ethernet 更
新。
2
Run Only
執行程式。
TPD-283U-H 旋轉開關的配置模式定義:
No
模式
說明
0
Run & Update
(Ethernet)
執行/更新程式，用於程式開發階段 (能
執行程式，也能進行更新)。(出廠預設)
1
Ethernet Force
Update
強制更新，當 TouchPAD 上的程式嚴
重毀損時可用此模式透過 Ethernet 更
新。
2
Run Only
執行程式。
9
USB Force
Update
透過 USB 更新程式。
網路設定出廠預設如下表:
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1

Technical support: servic[email protected] P8
4 第一次使用 TPD 2.8” H 系列
1. 如左圖所示，將電源和接地線連接完成。或是
若有 RJ-45 的乙太網路接孔，可以準備一條網路
線，透過乙太網路供電 (PoE)。然後將旋轉開關
(Rotary Switch) 轉到 0 (此時尚未供電)。
2. 開始供電給 TPD-283-H/283U-H，等待約數秒的開機
時間，接著可以看到 TPD-283-H/283U-H 執行出貨預附
的程式如右圖所示。
3. 試著按一下 TPD-283-H/283U-H 螢幕上面的圖示，
TPD-283-H/283U-H 會切到其他的頁面。
5 硬體安裝
乙太網路供電
使用一字起子來配置旋轉開關
安裝於專用明盒 EWB-T28(選購)
安裝於專用暗盒 OB120 (選購)
外部供電器
GND
VDC (+12-+48 V)