ICPDAS TPD-433F-H User manual

Technical support: servic[email protected] P1
TPD-433F-H
Quick Start
v1.1, Jan. 2019
What’s in the box?
Related Information
Thanks for buying ICPDAS TPD-433F-H device. This shipping
package contains the following items:
TPD-433F-H x 1
Quick Start x 1
(This Document)
M 2.6 x 12 L Round
Head Screws x 4
If you are new to TPD-433F-H, please read the “Chapter 3. Getting
Started”
of the TouchPAD Hardware User Manual
for detailed
information about install the free development tool –HMIWorks and
how to create your first project.
Documents, such as the User Manuals, the API References,
etc.: http://ftp.icpdas.com/pub/cd/touchpad/document/
Free Development Software, HMIWorks v2.10.10 or above:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email.

Technical support: servic[email protected] P2
1 Appearance
Front View Rear View
2 Pin Assignments
Pin
Description
F.G.
Frame Ground. F.G. is connected to the inside EMI or ESD
suppression circuits. Make sure that F.G. is connected to the
Earth
VDC
DC input Voltage (range: +12 V ~ +48 V)
GND
Connected to the power supply’s ground pin
D1+
The positive data line of the RS-485 network
D1-
The negative data line of the RS-485 network
GND
Ground pin
TxD2
The pin of transmitted data of the RS-232
RxD2
The pin of received data of the RS-232
Buzzer
LED Indicator
4.3”TFT LCD with
Touch Panel
Reset Button
Ethernet
Serial Port
USB
Rotary Switch

Technical support: servic[email protected] P3
3 Rotary Switch & Default Settings
The definition of the rotary switch:
No
Mode
Description
0
Run &
Update
(Ethernet)
This is a special run mode which is used in
the development stage. The TouchPAD
device can be updated by a PC from the
remote side through Ethernet. (Default)
1
Ethernet
Force
Update
While the application run on the TouchPAD
device seriously crashes, use this mode to
update a new application to the TouchPAD
device through Ethernet.
2
Run Only
Run the program.
9
USB Force
Update
Update a new application to the TouchPAD
device through USB.
Network Default Settings
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4 First Use of the TPD-433F-H
1. Connect wires as the below figure or prepare an Ethernet cable which
will be used to supply power through PoE if there’s a RJ-45 Ethernet port
on it. And set the rotary switch to 0 (At this point, the power is not yet
supplied).

Technical support: servic[email protected] P4
2. Supply power to the TPD-433F-H, wait
for several seconds and then you can see
the default program run on it.
3. Try to touch on the icons on the bottom-right corner of the screen of
the TPD-433F-H and you can find that TPD-433F-H switches to the
setting pages.
5 Hardware Installation
TPD-433F-H with External Wall Box,
EWB-T43F (optional)
TPD-433F-H with Outlet Box,
OB140F (optional)
PoE Switch
Use a flat-head screwdriver to set rotary switch
External Power
GND
VDC (+12-+48 V)

Technical support: servic[email protected] P5
TPD-433F-H 快速入門指南
v1.1, 2019年1月
檢查配件
參考資訊
感謝您購買泓格的
TPD-433F-H
產品。產品包裝內應包含下列配件
:
TPD-433F-H x 1
產品須知 x 1 (本文件)
M 2.6 x 12 L
圓頭螺絲 x 4
如果您是第一次使用
TPD-433F-H，請參閱 TouchPAD 硬體使用手冊
的
“第3 章啟動 TouchPAD” 來了解如何安裝免費的開發軟體
HMIWorks
並建立第一個專案以及更多詳細的相關資訊。
相關文件，如使用手冊、應用程式介面指南(API Reference) 等:
http://ftp.icpdas.com/pub/cd/touchpad/document/
免費開發軟體，HMIWorks 版本 2.10.10 或以上版本:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
如有任何問題歡迎使用
E-mail
聯繫我們，我們將會為您提供完善的咨
詢服務。

Technical support: servic[email protected] P6
1 外觀
前配置圖 後配置圖
2 腳位定義
Pin
說明
F.G.
機架接地，F.G. (連接到內部的 EMI 或ESD 保護電路)，
請接到大地
VDC
直流電壓輸入 (範圍：+12 V ~ +48 V)
GND
連到電源的接地端
D1+
RS-485 網路的正訊號線
D1-
RS-485 網路的負訊號線
GND
接地端
TxD2
RS-232 的傳送資料腳位
RxD2
RS-232 的接收資料腳位
蜂鳴器
LED 指示燈
4.3 吋觸控液晶螢幕
重啟按鈕
序列埠
USB
旋轉開關
Ethernet

Technical support: servic[email protected] P7
3 旋轉開關及出廠預設值
旋轉開關的配置模式定義:
No
模式
說明
0
Run & Update
(Ethernet)
執行/更新程式，用於程式開發階段 (能
執行程式，也能進行更新)。(出廠預設)
1
Ethernet Force
Update
強制更新，當 TouchPAD 上的程式嚴
重毀損時可用此模式透過 Ethernet 更
新。
2
Run Only
執行程式。
9
USB Force
Update
透過 USB 更新程式。
網路設定出廠預設如下表:
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4 第一次使用 TPD-433F-H
1. 如下圖所示，將電源和接地線連接完成。或是若有 RJ-45 的乙太網路
接孔，可以準備一條網路線，透過乙太網路供電 (PoE)。然後將旋轉開關
(Rotary Switch) 轉到 0 (此時尚未供電)。

Technical support: servic[email protected] P8
2. 開始供電給 TPD-433F-H，等待約數秒
的開機時間，接著可以看到 TPD-433F-H
執行出貨預附的程式如左圖所示。
3. 試著按一下 TPD-433F-H 螢幕上面的圖示，TPD-433F-H 會切到其他
的頁面。
5 硬體安裝
乙太網路供電
使用一字起子來配置旋轉開關
外部供電器
GND
VDC (+12-+48 V)
TPD-433F-H
安裝於專用明盒
EWB-T43F(選購)
TPD-433F-H
安裝於專用暗盒
OB140F (選購)