Icron EL5200 HDMI + USB 2.0 Extender User manual

EL5200 HDMI® + USB 2.0 Extender
HDMI® and USB 2.0 100m Cat 5e KVM Extender System
User Guide

Thank you for purchasing the EL5200 KVM Extender.
Please read this guide thoroughly.
FCC Radio Frequency Interference Statement Warning
This device complies with FCC Part 15 Subpart B.
CE Statement
The product meets European Standard EMC EN 55022 Class A, EN 61000, and EN 55024.
IC Statement
This Class A digital apparatus complies with Canadian ICES-003.
©2013 Icron Technologies Corporation.All rights reserved. Icron Technologies Corporation, the Icron
Technologies Corporation logo, and the Icron Technologies Corporation products referred to herein are
either the trademarks or the registered trademarks of Icron Technologies Corporation. All other trademarks
are property of their respective owners. Icron Technologies Corporation assumes no responsibility for errors
that may appear in this manual.Information contained herein is subject to change without notice.
Document #90-01011-A04

Contents
Introduction...................................................................................................................... 4
Product Contents...........................................................................................................................................................................4
Requirements..................................................................................................................................................................................4
About the EL5200 KVM Extender.............................................................................................................................................4
Compatibility and Recommended Setup ............................................................................................................................5
Local Extender (LEX) Description and Markings................................................................................................................6
Remote Extender (REX) Description and Markings...........................................................................................................7
Installation Guide ............................................................................................................. 8
Installing the LEX Unit..................................................................................................................................................................8
Installing the REX Unit.................................................................................................................................................................8
Connecting the LEX to the REX................................................................................................................................................9
Connecting Power to the LEX and REX .................................................................................................................................9
Checking the Installation............................................................................................................................................................9
Connecting a USB Device...........................................................................................................................................................9
Troubleshooting Guide .................................................................................................. 10
Specifications.................................................................................................................. 12
Contacting Technical Support ....................................................................................... 13
Warranty Information .................................................................................................... 13
Obtaining Warranty Service .......................................................................................... 14
Technical Glossary ......................................................................................................... 15

Introduction
The instructions in this guide assume a general knowledge of computer installation procedures, familiarity
with cabling requirements, and some understanding of USB devices.
NOTES provide additional useful and important information.
CAUTIONS provide important information about an operational requirement.
Product Contents
• Local Extender (LEX)
• Remote Extender (REX)
• (2) 5V DC power adapter
• USB Cable
• HDMI Cable
• Quick Start Guide and Warranty Information
The product requires two power adapters, one for the LEX and one for the REX.
This product supports Cat 5e or better cabling (i.e. Cat 6, Cat 7, etc). All references to“Cat 5e”
should be read as“Cat 5e or better”.
Requirements
To complete the installation, you will require the following items that are not included with the product:
• A computer that is USB compatible (with USB compliant operating system) and has an HDMI port;
• USB 1.1 or 2.0 compatible device(s);
• A minimum of Cat 5e Shielded Twisted Pair (STP) cable with two Cat 5e RJ45 connectors (if using
surface cabling),
OR
• A minimum of Cat 5e cabling with two information outlets and two Cat 5e patch cords with Cat 5e
RJ45 connectors (if using premise cabling).
While Cat 5e STP is the minimum category of twisted pair cabling, for the best experience, and to
minimize interference and cross-talk, Cat 6 STP or better is strongly recommended. When using
Cat 5e cabling, the layout and quality of your cable runs and connections becomes extremely
important. Please refer to the Cabling section on page 5 for more detailed information.
About the EL5200 KVM Extender
The EL5200 KVM Extender system incorporates ExtremeUSB® and HD video technology, which enables users
to extend both HDMI video and USB 2.0 up to 100 meters (330 feet). The following ExtremeUSB features are
included:
• True Plug and play. No installation of software drivers required.
• Supports all major operating systems: Windows®, Mac OS X®, and Linux®
• Reliable operation with USB 2.0 and 1.1 devices and hubs
• Patented USB extension technology
note
note
note
note
4

Compatibility and Recommended Setup
The product is compatible with many graphics cards,operating systems and monitors, and supports high
definition video resolutions of up to 1080p, 1920 x 1200, and 4K. However, there is no guarantee that all
devices will be compatible with the product as there are a number of different factors that may impact the
operation of this KVM Extender.
This product supports both USB 1.1 and 2.0 devices.These devices include: keyboards, mice, flash drives,
microphones, speakers, printers, and USB 1.1 web cameras. If uncertain whether your USB 2.0 device(s) can
be supported, please contact Technical Support: icron.com/support.
USB 2.0 devices are limited to 30Mbps of throughput. Not all USB 2.0 devices will reach full
performance as a result.
HDMI Cables
Poorly terminated HDMI cables may result in damage to the devices they are connected to. Please ensure
that you use the HDMI cable provided with the product when connecting the LEX (Local Extender)
to the host computer and high quality HDMI cables for all other HDMI connections.
Cabling
Solid core Category 6 STP cable with Category 6 RJ45 connectors is recommended for best
performance. Using Cat 5e or unshielded Cat 6 cabling may leave your signal more susceptible to
interference and noise which may result in poor video performance or reduced extension distance.
Cable Type Maximum Distance
Uncoiled Coiled
Notes
Solid Core Cat 5e UTP 100m (330 ft) 70m (229 ft) High susceptibility to electrical interference
Solid Core Cat 5e STP 100m (330 ft) 80m (262 ft) Moderate susceptibility to electrical interference
Solid Core Cat 6 UTP 100m (330 ft) 100m (330 ft) High susceptibility to electrical interference
Solid Core Cat 6 STP 100m (330 ft) 100m (330 ft) Recommended
Solid Core Cat 7 STP 100m (330 ft) 100m (330 ft) Recommended
Host Operating Systems
• Windows®
• Mac OS X®
• Linux®
USB Peripherals
• Keyboards&Mice • Printers
• MassStorageDevices • Speakers
• USB1.1WebCameras • Microphones
HDMI Features
The EL5200 KVM Extender is compatible with the following HDMI features:
• Full uncompressed high definition 1080p, 1920 x 1200, and 4K video resolution
• Depth perception of 2D and 3D
• Deep Color and x.v. Color
• Lip Sync Pass-through
• CEC Pass-through
• HDCP Pass-through 5
note

Local Extender (LEX) Description and Markings
The LEX connects to the host computer using the supplied HDMI and USB cable.
It’s important to use the HDMI cable supplied with the product when connecting the LEX to the host
computer to ensure proper operation.
ITEM TYPE DESCRIPTION
1 Power LED (Green) Green Light: The system is powered and ready to use.
No Light: The system does not have power.
2 Link LED (Green)
Green Light: The LEX and REX are able to communicate with each other
across the link.
No Light: There is no communication between the LEX and REX.
3 USB LED (Green)
Green Light: The LEX and the host computer are communicating with each
other and working.
Blinking Green Light: The host has suspended communication with the LEX.
No Light: The host and the LEX are not communicating or not connected.
4 Video LED (Green)
Solid Green Light: HDCP (digital rights management) content is being
transmitted.
Blinking Green Light: Video (non-HDCP) content is being transmitted.
No Light: There is no video being transmitted.
5 Link Port (RJ45) Accepts RJ45 connector for Cat 5e cabling.
6 Config Reserved for use by Icron Technologies and its technology partners.
7 HDMI In Accepts HDMI connector for video input from the host computer.
8 Device Port (USB Type B) Connects the LEX to the host computer.
9 Power Port Connects to the 5V, 3A power adapter.
6
Front View
89
5
Rear View
7
6
1 2 3 4
Power
Link
USB
Video
Local Extender
EL5200
HDMI InConfig 5V DCLink

Remote Extender (REX) Description and Markings
The REX provides HDMI output to a monitor and three USB Type A ports for standard USB devices.Additional
devices may be connected by attaching USB hubs.
ITEM TYPE DESCRIPTION
1 Power LED (Green) Green Light: The system is powered and ready to use.
No Light: The system does not have power.
2 Link LED (Green) Green Light: The LEX and REX are able to communicate with each other
across the link.
No Light: There is no communication between the LEX and REX.
3 USB LED (Green) Green Light: The LEX and the host computer are communicating with each
other and working.
Blinking Green Light: The host has suspended communication with the LEX.
No Light: The host and the LEX are not communicating or not connected.
4 Video LED (Green) Solid Green Light: HDCP (digital rights management) content is being
transmitted.
Blinking Green Light: Video (non-HDCP) content is being transmitted.
No Light: There is no video being transmitted.
5 Link Port (RJ45) Accepts RJ45 connector for Cat 5e cabling.
6 HDMI Out Accepts HDMI connector to the remote monitor.
7 Config Reserved for use by Icron Technologies and its technology partners.
8 Device Port (USB Type A) Accepts USB device(s).
9 Power Port Connects to the 5V, 3A power adapter.
7
8 8 8
Front View
5
Rear View
1 2 3 4
7
6
9
HDMI Out Config 5V DCLink
Power
Link
USB
Video
Remote Extender
EL5200

Installation Guide
Before you can install the product, you need to prepare your site:
1. Determine where the computer is to be located and set up the computer.
2. Determine where you want to locate the remote desktop, including the monitor, keyboard, mouse
and any other USB device(s).
3. If you are using surface cabling, the product supports a maximum distance of 100m (330 ft).
OR
If you are using premise cabling, ensure Cat 5e cabling is installed between the two locations,with
Cat 5e information outlets located near both the computer and the USB device(s), and the total
length, including patch cords, is no more than 100m.
Installing the LEX Unit
1. Place the LEX unit near the computer.
2. Connect the supplied USB cable to the USB port on the LEX, and an available USB 2.0/1.1 Type A Port
on the computer.
3. Connect the supplied HDMI cable to the LEX (HDMI In), and an available HDMI Port on the
computer.
Installing the REX Unit
1. Place the REX unit near the monitor and USB device(s) in the desired remote location.
2. Connect an HDMI cable (not included) to the REX (HDMI Out) to the monitor.
3. Plug your USB Device(s) into the USB ports on the REX.
8
LEX
Home Theater PC
(source)
HD TV/Monitor
(sink)
HDMI & USB
up to 100m Cat 5e
REX

Connecting the LEX to the REX
With Surface Cabling
1. Plug one end of the Cat 5e cabling (not included) into the Link port (RJ45) on the LEX.
2. Plug the other end of the Cat 5e cabling into the Link port (RJ45) on the REX.
With Premise Cabling
1. Plug one end of a Cat 5e patch cord (not included) into the Link port (RJ45) on the LEX.
2. Plug the other end of the patch cord into the Cat 5e information outlet near the host computer.
3. Plug one end of the second Cat 5e patch cord (not included) into the Link port (RJ45) on the REX.
4. Plug the other end of the second patch cord into the Cat 5e information outlet near the USB device(s).
Connecting Power to the LEX and REX
1. Plug the supplied 5V, 3A power adapter into a suitable AC outlet near the LEX.
2. Connect the power adapter to the LEX.
3. Plug the supplied 5V, 3A power adapter into a suitable AC outlet near the REX.
4. Connect the power adapter to the REX.
Use only the power adapters supplied with the product. Use of substitute adapters may cause permanent
damage to the system and will void the warranty.
Checking the Installation
1. On the LEX and REX units, check that the Power, Link, USB, and Video LEDs are on. If the Link LED is off,
then the cabling between the LEX and REX unit is not installed properly or is defective.
2. Check to see if the USB LED is on and the Video LED is blinking or on, if they are not, this indicates
there is no USB data or video data. Check the HDMI and USB connections to the host computer, and
the HDMI connection to the monitor. Check to see if any USB devices are connected to the REX.
3. If the product is not displaying video or your USB device fails to be detected by your operating system,
consult the Troubleshooting Guide.
Connecting a USB Device
1. Install any software required to operate the USB device(s). Refer to the documentation provided for
your USB device(s), as required.
2. Connect the USB device to the device port on the REX.
3. Check that the USB device is detected and installed properly in the operating system.
9

Troubleshooting Guide
The following table provides troubleshooting tips. The topics are arranged in the order in which they should
be executed in most situations. If you are unable to resolve the problem after following these instructions,
please contact Technical Support for further assistance.
PROBLEM CAUSE SOLUTION
All LEDs on LEX
are off.
• The LEX is not receiving power
from the power adapter.
1. Ensure that the power adapter is properly
connected to the LEX.
2.Check that the power adapter is connected to a
live source of electrical power.
All LEDs on REX
are off.
• The REX unit is not receiving
power from the power adapter.
1. Ensure that the power adapter is properly
connected to the LEX.
2.Check that the power adapter is connected to a
live source of electrical power.
Link LEDs on
LEX and REX are
off.
•Thereisnoconnectionbetween
the LEX and REX.
1. Ensure a Cat 5e cable is connected between the
LEX and REX. Ensure Cat 5e STP or better cabling
with conductor RJ45 connectors is used.
2.Connect a new short Cat 5e patch cord between
the LEX and REX to determine if the original Cat 5e
cable is defective.
3. Ensure the Cat 5e cable is as straight as possible
(i.e. not coiled).
Link LED on LEX
is on, USB LED
on LEX is off.
• The host computer is not
powered on.
• The LEX is not connected to the
computer.
• The computer does not support
USB hubs.
• The USB cable is defective.
• The unit is malfunctioning.
1. Disconnect all USB devices from the REX.
2.Disconnect the LEX from the computer.
3. Disconnect the LEX and REX from the power
adapters.
4. Reconnect the LEX to the power adapter.
5. Reconnect the REX to the power adapter.
6. Reconnect the USB devices to the REX.
7. Reconnect the LEX to the computer.
8.If the USB LED continues to stay off, contact
Technical Support.
10