ICT PRT-WX-DIN User manual

PRT-WX-DIN
Protege WX DIN Rail Integrated System
Controller
Installation Manual

The specifications and descriptions of products and services contained in this document were correct at the
time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw
products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form
or by any means (electronic or mechanical), for any purpose, without the express written permission of
Integrated Control Technology Limited. Designed and manufactured by Integrated Control Technology Limited,
Protege® and the Protege® Logo are registered trademarks of Integrated Control Technology Limited. All other
brand or product names are trademarks or registered trademarks of their respective holders.
Copyright © Integrated Control Technology Limited 2003-2021. All rights reserved.
Last Published: 25-May-21 4:29 PM
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 2

Contents
Introduction 6
Installation Requirements 7
Grounding Requirements 8
Safety Grounding 8
Earth Ground Connection 8
Mounting 10
Removal 10
Wiring Diagram 11
Connections 12
Power Requirements 12
Auxiliary Outputs 14
Encrypted Module Network 14
Module Wiring 14
End of Line (EOL) Resistors 15
Telephone Dialer 15
Ethernet 10/100 Network Interface 16
Door Access Control 17
Wiegand Reader Connection 17
Multiple Wiegand Reader Connection 18
RS-485 Reader Locations 18
RS-485 Reader Connection (Entry Only) 19
RS-485 Reader Connection (Entry/Exit) 19
Door Contact Connection 19
Lock Output Connection 20
Programming the Onboard Reader 21
Inputs 22
EOL Resistor Value Options 23
Duplex Inputs 23
Trouble Inputs 24
Outputs 27
Bell/Siren Output 27
Relay Outputs 28
Reader Outputs 28
Configuration 29
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 3

Logging In for the First Time 29
Creating a Secure Password 29
Registering Your Controller 30
Set the Controller Time 30
Configuring the IP Address 31
Setting Up Integrated DDNS 32
Setting Up an HTTPS Connection 33
Connectivity Requirements for HTTPS 33
Third-Party Certificate 35
Self-Signed Certificate 37
Maintaining Your System 39
Signing In 39
Home Page 39
System Settings 40
Settings | Configuration 41
Settings | Options 41
Settings | Email 42
Settings | Custom Reader Format 43
Settings | Security Enhancement 43
Operators 44
Roles 45
Backing Up and Restoring Controller Programming 45
Upgrading Application Software and Module Firmware 46
Setting the IP Address from a Keypad 48
Temporarily Defaulting the IP Address 49
Defaulting a Controller 50
LED Indicators 51
Power Indicator 51
Status Indicator 51
Fault Indicator 51
Ethernet Link Indicator 51
Modem Indicator 52
Reader Data Indicators 52
Bell Indicator 52
Relay Indicators 52
Input Indicators 53
Mechanical Diagram 54
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 4

Mechanical Layout 55
Technical Specifications 56
Current and Validation Example 57
New Zealand and Australia 58
Intruder Detection Maintenance Routine 58
Peripheral Devices 58
Testing Frequency 58
Recommended Routine Maintenance Procedures 59
European Standards 62
UK PD 6662:2017 and BS 8243 63
UL and ULC Installation Requirements 64
UL/ULC Installation Cabinet Options 64
Central Station Signal Receiver Compatibility List 64
UL Operation Mode 65
ULC Compliance Requirements 65
CAN/ULC-S304 65
CAN/ULC-S319 68
CAN/ULC-S559 68
UL Compliance Requirements 72
UL1610 72
UL294 73
FCC Compliance Statements 75
Industry Canada Statement 77
Disclaimer and Warranty 78
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 5

Introduction
The Protege WX DIN Rail Integrated System Controller is the central processing unit responsible for the control
of security, access control and building automation in the Protege WX system. It communicates with all system
modules, stores all configuration and transaction information, processes all system communication, and reports
alarms and system activity to a monitoring station or remote computer.
Flexible module network architecture allows large numbers of modules to be connected to the RS-485 module
network. Up to 250 modules can be connected to the Protege system in any combination to the network, over a
distance of up to 900M (3000ft). Further span can be achieved with the use of a network repeater module.
The current features of the controller include:
⦁Internal industry standard 10/100 ethernet
⦁32 Bit advanced RISC processor with 2Gb total memory
⦁Encrypted module network using RS-485 communication
⦁NIST Certified AES 128, 192 and 256 Bit Encryption
⦁Factory loaded HTTPScertificate
⦁OSDPconfigurable RS-485
⦁8 high security monitored inputs
⦁Built-in offsite communications dialer (ContactID or SIA)
⦁Industry standard DIN rail mounting
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 6

Installation Requirements
This equipment is to be installed in accordance with:
⦁The product installation instructions
⦁UL 681 - Installation and Classification of Burglar and Holdup Systems
⦁UL 827 - Central-Station Alarm Services
⦁CAN/ULC-S301, Central and Monitoring Station Burglar Alarm Systems
⦁CAN/ULC-S302, Installation and Classification of Burglar Alarm Systems for Financial and Commercial
Premises, Safes and Vaults
⦁CAN/ULC-S561, Installation and Services for Fire Signal Receiving Centres and Systems
⦁The National Electrical Code, ANSI/NFPA 70
⦁The Canadian Electrical Code, Part I, CSA C22.1
⦁AS/NZS 2201.1 Intruder Alarm Systems
⦁The Local Authority Having Jurisdiction (AHJ)
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 7

Grounding Requirements
An effectively grounded product is one that is intentionally connected to earth ground through a ground
connection or connections of sufficiently low impedance and having sufficient current-carrying capacity to
prevent elevated voltages which may result in undue hazard to connected equipment or to persons.
Grounding of the Protege system is done for three basic reasons:
1. Safety
2. Component protection
3. Noise reduction
Safety Grounding
The object of safety grounding is to ensure that all metalwork is at the same ground (or earth) potential.
Impedance between the Protege system and the building scheme ground must conform to the requirements of
national and local industrial safety regulations or electrical codes. These will vary based on country, type of
distribution system and other factors. The integrity of all ground connections should be checked periodically.
General safety dictates that all metal parts are connected to earth with separate copper wire or wires of the
appropriate gauge.
Earth Ground Connection
The DIN rail enclosure and the DIN rail modules must be grounded to a suitable single-point earth ground
connection in the installation. A minimum 14AWG solid copper wire (or thicker, in accordance with local
authorities) shall be used from the Protege system's earth connection points.
The DIN rail enclosure includes an earth ground single-point link connection via the metallic enclosure. This
single-point link is the Protege system's earth ground. All modules that have earth ground connections and that
are installed in the same enclosure shall be connected to this single point. A single-point earth ground
connection avoids the creation of ground loops in the system and provides a single reference point to earth
ground.
Reader Expander
Input Expander
Output Expander
Controller
Dialer’s Earth
Ground Connection
Power Supply
V-
DIN Rail Ground Connections (one or more cabinets installed in the same room)
DIN Rail Enclosure Additional DIN Rail Enclosure(s)
Module Network
(RS-485 N+, N-, NA, NB)
AC Mains Wiring
Earth Ground
Link Connection
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 8

Sector or Building #2Sector or Building #1 Sector or Building #3
Input Expander
Input Expander
Input Expander
Reader Expander
Input Expander
Output Expander
Power Supply
Controller
Dialer’s Earth
Ground Connection
V-
Earth Ground
Link Connection
DIN Rail Enclosure DIN Rail Enclosure DIN Rail Enclosure
Module Network (RS-485 N+, N-, NA and NB)
DIN Rail Ground Connections (multiple cabinets in different rooms, sectors, or buildings)
Note that the DIN rail enclosure earth terminal is connected to the power supply V- terminal.
There must be only one single earth grounding point per system.
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 9

Mounting
Protege DIN rail modules are designed to mount on standard DIN rail either in dedicated DIN cabinets or on
generic DIN rail mounting strip.
When installing a DIN rail module, ensure that there is adequate clearance around all sides of the device and
that air flow to the vents of the unit is not restricted. It is recommended that you install the module in a location
that will facilitate easy access for wiring. It is also recommended that the module is installed in an electrical
room, communication equipment room, secure cabinet, or in an accessible area of the ceiling.
1. Position the DIN rail module with the labeling in the correct orientation.
2. Hook the mounting tabs (opposite the tab clip) under the edge of the DIN rail.
3. Push the DIN rail module against the mount until the tab clips over the rail.
Removal
A Protege DIN rail module can be removed from the DIN rail mount using the following steps:
1. Insert a flat blade screwdriver into the hole in the module tab clip.
2. Lever the tab outwards and rotate the unit off the DIN rail mount.
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 10

Wiring Diagram
Shield
Red
Black
Green
White
Orange
Brown
Blue
Yellow
Shield
Red
Black
Green
White
Orange
Brown
Blue
Yellow
NAN+ N- NB
Next modules
on network
NAN+ N- NB
White
Blue
Black
Red
UL Listed
Power Supplyor
modulesupplying
power to networked
devices
+
-
+
1k
1N4007
Diode
1.1A (Typical)
Electric
Locking Device
8Ohm30W
Siren or 1.1A
(Typical)
-
+
-
LockPower
Supply
+
-
1N4007
Diode
Electric Locking
Device
+
-
LockPower
Supply
+
-
1N4007
Diode
Electric Locking
Device
RJ31X
Grey
Brown
Red
Green
Cold water
earth pipe
SecuritySystem
User Interface
Wiring
EARTH GND WIRING:Minimum 14AWG solid
copper wire.
INPUT WIRING:maximum distance of 300m (1000ft)
from the Controller when using 22 AWG
AUX WIRING:Min 22AWG Max 16AWG. (Depends on
length and Current consumption). For wire/cable size,
a maximum of 5% voltage drop at the terminals of
the powered device has to be observed.
ETHERNET WIRING:CAT5e / CAT6 max 100m (330 ft)
MODULE NETWORK WIRING:Recommended Belden
9842 or equivalent. (24AWG twisted pair with
characteristic impedance of 120ohm or CAT5e / CAT6
are also supported for Data Transmission when using
ground in the same cable.
Do not use extra wires to
power devices.)max 900m (3000ft).
Configuration
ConnectReader 1 D0 to L1then power cycle the
Controller to forceitto use 192.168.111.222 as
it's IP address.
ConnectReader 2 D0 to L1then power cycle the
Controller to reset it to factory defaults. Note:
this will not reset the Ethernet settings.
Reader 2 Reader 1
If not used for Reader functions the Reader
outputs (L1& BZ) can be used as general
purposeouputs. They are Open Collector Outputs
& switch to 0V. The outputs can be used to
activate relays, sounders and lights.
1K5 OHM
Z4 V- Z3 Z2 V- Z1 V- V+
LED
Programmable Outputs (L1 & BZ)
LED Description
Power Green Power is applied
Off Low or no power is applied
Status Flashing green Normal operation
Fault Red A fault has occurred
Off Normal operation
Ethernet
Green Ethernet connection present
Off No Ethernet connection detected
Active Ethernet data
Modem Green Themodemhas control of thetelephone line
Off Modemnot active
R1 /R2 Data received but format is incorrect
Correctly formatted data received
Relay1/2 Red Relayis closed
Off Relayis open
Bell
Green Bell is turned on
Off Bell is connected and turned off
Bell is turned on, and the circuitis in
over-current protection
Bell is turned off, and the circuitis cut,
damaged or tampered
Zone1-8
Off The Input is not programmed
Red Input is in the OPEN state
Green Input is in the CLOSED state
Flashing red Input is in the TAMPERED state
Flashing green Input is in the SHORTED state
2green flashes
1green flash
Long red flash
Short red flash
Fast green flash
+AUX- Z1 COM COMZ2 Z3 Z4
N.C Input Contact
N. C
Tamper Value 2 Value 1
Typical Input Circuits
Value 1 Value 2 Monitored Status
No Resistor No Resistor Open, Closed
1k 1k Open, Closed, Tamper, Short
2k2 6k8 Open, Closed, Tamper, Short
10k 10k Open, Closed, Tamper, Short
2k2 2k2 Open, Closed, Tamper, Short
4k7 2k2 Open, Closed, Tamper, Short
4k7 4k7 Open, Closed, Tamper, Short
CAUTION:
INCORRECT
WIRING MAY RESULT IN
DAMAGE TO THE UNIT
Input Options
The onboard reader ports use inputs 1 – 8 as
door contact, REX, bond sense and REN inputs
respectively. Any of these inputs that are not
configured for use with the Onboard Reader
may be used as general purpose inputs. Refer to
the Controller Installation Manual for instructions
on programming the onboard reader.
BZ L1 NB NA Z8 V- Z7 Z6 V- Z5 V- V+ BZ L1 NB NA Z4 V- Z3 Z2 V- Z1 V- V+
READER 2 READER 1
ZONE INPUT 5-8 ZONE INPUT 1-412VDC OUT 12VDC OUT
D1/ D0/ D1/ D0/
Controller
For UL applications,must be powered by aUL
Listed (UL 603 or UL 294) power limited power
supply capableof supplying at least 4 hours of
standby power. For ULC application, must be
powered by a ULC Listed (CAN/ULCS318) or
(CAN/ULC-S319 power limited power supply
capable of supplying at least 24 hours.
External Power Supply
Optional UL
Listed Reader
EOL Resistor Input Configuration
N.C Input Contact
Door Contact 1K 1K
REX 1K 1K
N . O Input Co nt act
N.C Input Contact
Bond Sense 1K 1K
REN 1K 1K
N . O Input Co nt act
Optional UL
Listed Reader
N.C Input Contact
1K 1K Door Contact
1K 1K REX
N . O Input Cont act
N.C Input Contact
1K 1K Bond Sense
1K 1K REN
N . O Input Co nt act
Input
LON
Interface
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 11

Connections
Power Requirements
Power is supplied to the controller by a 12V DC power supply connected to the N+ and N- terminals. The
controller does not contain internal regulation or isolation and any clean 12V DC supply is suitable for this
purpose.
Termination of wiring to the module while power is applied or the battery is connected may cause serious
damage to the unit and will VOID ALL WARRANTIES OR GUARANTEES.
Power the unit only after all wiring, configuration and jumper settings are completed.
A battery backup must be connected to the module network to provide a monitored supply. The battery plays
an important role in power conditioning and provides a continuous source of power in the event of a power
outage.
Example 2A Power Supply Connection:
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 12

Example 4A Power Supply Connection:
In a small installation this same power supply can be used to supply the module network as well, so long as the
maximum load of the power supply is not exceeded. In larger installations, the power supply may need to be
split to allow for load sharing between several supplies.
To comply with EN 50131-1 only one battery can be connected and monitored per system. If more capacity is
required a single larger battery must be used.
Example Multiple PSU Connection:
When using multiple power supplies it is important to ensure that all ground connections (V-) are connected
between all power supplies and that no power connections (V+) are connected between any power supplies.
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 13

Auxiliary Outputs
The auxiliary outputs (V- V+) of the controller can be used to supply other equipment. Note that there is no
onboard regulation or isolation for these outputs; they are a fused feed-through from the N+ N- input terminals.
When using these outputs to supply other devices, be sure not to exceed the rating of the internal fuses as
outlined in the Technical Specifications.
Encrypted Module Network
The controller incorporates encrypted RS-485 communications technology. Connection of the communications
should be performed according to the following diagram.
PSU or
equivalent 12V DC
Shield is frame
grounded at
one point
Shields are
connected together
and Isolated
Shielded Cable
Controller Network Module Network Module
Shielded Cable
Shield not
connected
supply
NAN+ N- NB NAN+ N- NB
NAN+ N- NB
Always connect the controller's NA and NB terminals to the NA and NB terminals of the expansion devices and
keypads. The N+ and N- must connect to a 12V power supply source capable of supplying the peak current
drawn by all modules. If a shielded cable is used, the shield must be connected at only one end of the cable. DO
NOT connect a shield at both ends.
The 12V N+ and N- communication input must be supplied from only one point. Connections from more than
one 12V supply may cause failure or damage to the unit or the device supplying network power. Make sure
that the power supply can supply enough current for the peak load drawn by all modules connected to the
12V supply, including the controller itself.
Module Wiring
The recommended module network wiring specifications are:
⦁Belden 9842 or equivalent
⦁24AWG twisted pair with characteristic impedance of 120 ohm
⦁Maximum total length of cable is 900m (3000ft)
⦁CAT5e / CAT6 are also supported for data transmission when using ground in the same cable (to a
maximum length of 100m (328ft))
Warning: Unused wires in the cable must not be used to carry power to other devices.
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 14

End of Line (EOL) Resistors
The 330 ohm EOL (End of Line) resistor provided in the accessory bag must be inserted between the NA and
NB terminals of the first and last modules on the RS-485 network. These are the modules physically located at
the ends of the RS-485 network cabling.
330R 330R
First Module on RS-485 Network Last Module on RS-485 Network
To
Next
Module
From
Previous
Module
NAN+ N- NB
NAN+ N- NB
Telephone Dialer
The controller provides the ability to communicate alarms and upload information to remote systems using the
onboard 2400bps modem. The telephone line can be connected directly to the controller using the onboard
telephone connection terminals.
Telco line out
Telco line
tip and ring input
R1i T1o R1o
T1i
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 15

Ethernet 10/100 Network Interface
The communication between the Protege system and the controller uses a 10/100 ethernet network operating
the TCP/IP protocol suite. The IP address of the controller can be configured using an LCD keypad terminal or
via the built-in web interface. The default IP address is set to a static address of 192.168.1.2 with a subnet mask
of 255.255.255.0. These IP address settings are commonly used for internal networks.
Installing the module on an active network requires knowledge of the configuration and structure for the
network. Always consult the network or system administrator and ask them to provide you with a fixed IP
address that can be assigned to the module.
When installing an ethernet connection the module should be interfaced using a standard segment (<100m in
length) and should be connected to a suitable ethernet hub or switch:
Ethernet 10/100 Switch hub Connection:
Controller
Controller
Temporary direct connections can be used for onsite programming by using a standard ethernet cable.
Ethernet 10/100 Direct Connection:
Controller
P
UL
ULC
⦁All network equipment such as hubs/routers/gateways used with the controller must comply
with the UL and ULC standard requirements associated with a signal receiving center.
⦁The controller must be installed in the same room as the network equipment that provides it
the network connection.
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 16

Door Access Control
The controller provides access control functionality onboard without the requirement for additional hardware.
The controller allows the connection of 2 Wiegand devices to control 2 doors (entry or exit only) or 1 door (entry
and exit), or it can be configured in multiplex mode to allow 4 Wiegand devices controlling 2 doors with entry
and exit readers. Alternatively, the reader ports can be independently configured to connect RS485-based
readers.
The recommended cable types for RS-485 are:
⦁Belden 9842 or equivalent
⦁24 AWG twisted pair with characteristic impedance of 120ohm
The recommended cable types for Wiegand are:
⦁22 AWG alpha 5196, 5198, 18 AWG alpha 5386, 5388
Important:
⦁The card reader must be connected to the module port using a shielded cable.
⦁Do not connect the shield to an AUX-, 0V or V- connection on the module.
⦁Do not join the shield and black wires at the reading device.
⦁Do not connect the shield to any shield used for isolated communication.
⦁The shield connection must only be connected at one end of the cable in the metallic enclosure (frame
grounded).
P
UL
ULC
All UL listed ICT readers are shipped with single LED mode set as default and are fully
compatible with the Protege system, such as tSec Standard Readers, tSec Mini Readers, etc.
Wiegand Reader Connection
The controller allows the connection of 2 magnetic clock and data reading devices or 4 Wiegand reading
devices and the ability to control 2 doors (entry or exit only) or 1 door (entry and exit). The following diagrams
show the connection of a standard Wiegand reader with the controller controlling an access door and an
entry/exit door.
Shield is frame
grounded at
one point
Shielded Cable
RED
BLACK
GREEN
WHITE
ORANGE
BROWN
BLUE
YELLOW
SHIELD
Shield not
connected
V+
V-Z4 V- Z3 Z2 V- Z1BZ L1 D1/
NB
D0/
NA
1 2
3 4
5 6
7 8
9 0
X
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 17

Multiple Wiegand Reader Connection
Multiple reader mode allows the connection of 4 Wiegand reading devices controlling 2 doors each with
entry/exit readers.
In multiple reader mode, the secondary reader has all connections wired to the same port as the primary card
reader, with the DATA 1 connection wired to the opposite reader connection DATA 1 input.
The reader that is multiplexed into the alternate reader port will operate as the exit reader, and the normal
reader connection shall operate as the entry reader.
Shield is frame
grounded at
one point
Shielded Cable
Shielded Cable
RED
BLACK
GREEN
WHITE
ORANGE
BROWN
BLUE
YELLOW
SHIELD
RED
BLACK
GREEN
SHIELD
WHITE
ORANGE
BROWN
BLUE
YELLOW
Shield not
connected
V+
V-Z4 V- Z3 Z2 V- Z1BZ L1 D1/
NB
D0/
NA
BZ L1 D1/
NB
D0/
NA
ENTRY
EXIT
1 2
3 4
5 6
7 8
9 0
X
RS-485 Reader Locations
As two RS-485 readers can be connected to the same RS-485 reader port, configuration of the green and
orange wires uniquely identifies the reader, and determines which is the entry reader and which is the exit
reader.
Location Configuration
Entry Green and orange wires not connected.
Exit Green and orange wires connected together.
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 18

RS-485 Reader Connection (Entry Only)
The following diagram shows the connection of a single RS-485 reader connected in entry only mode.
Shield is frame
grounded at
one point
Shielded Cable
RED
BLACK
GREEN
WHITE
ORANGE
BROWN
BLUE
YELLOW
VIOLET
Shield not
connected
V+
V-Z4 V- Z3 Z2 V- Z1BZ L1 D1/
NB
D0/
NA
SHIELD
1 2
3 4
5 6
7 8
9 0
X
When the green and orange wires are not connected together, the reader defaults to an entry reader.
RS-485 Reader Connection (Entry/Exit)
The following diagram shows the connection of two RS-485 readers connected to provide an entry/exit
configuration.
Shield is frame
grounded at
one point
Shielded Cable
Shielded Cable
RED
BLACK
GREEN
WHITE
ORANGE
BROWN
BLUE
YELLOW
SHIELD
RED
BLACK
GREEN
SHIELD
WHITE
ORANGE
BROWN
BLUE
YELLOW
Shield not
connected
VIOLET
VIOLET
ENTRY
EXIT
1 2
3 4
5 6
7 8
9 0
X
V+
V-Z4 V- Z3 Z2 V- Z1BZ L1 D1/
NB
D0/
NA
The exit reader has the green and orange wires connected together.
A 330 ohm EOL (End of Line) resistor may be required to be inserted between the NA and NB terminals of the
reader and a second 330 ohm EOL resistor must then be inserted between the source NA and NB terminals at
the other end of the wiring.
Door Contact Connection
The module allows the connection of up to 4 contacts for monitoring and controlling access control doors. Each
input can be used for either the door function that is automatically assigned or as a normal input on the system.
The following example shows the connection of a normally closed door position monitoring contact to monitor
the open, closed, forced and alarm conditions of the door.
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 19

V+
V-Z4 V- Z3 Z2 V- Z1
N.C. Input Contact
N.C. Input Contact
N.O. Input Contact
N.O. Input Contact
1K
1K
1K
1K
1K
1K 1K
1K
Door Contact
Bond Sense
REN Input
REX Input
Inputs 1-4 and 5-8 can operate as either general purpose inputs or as onboard reader inputs. If used as general
purpose inputs, make sure that these inputs are not defined in the onboard reader set up.
Input Access Control Function Default Setting
Input 1 Door Contact, Port 1 Door Contact, Port 1
Input 2 REX Input, Port 1 REX Input, Port 1
Input 3 Bond Sense, Port 1 General Purpose Input
Input 4 REN Input, Port 1 General Purpose Input
Input 5 Door Contact, Port 2 Door Contact, Port 2
Input 6 REX input, Port 2 REX Input, Port 2
Input 7 Bond Sense, Port 2 General Purpose Input
Input 8 REN Input, Port 2 General Purpose Input
When connected the REX input can be programmed to operate regardless of the door contact state. The REX
input can also be programmed to recycle the door alarm time to prevent nuisance alarms when the door is held
open to permit longer entry.
P
UL
ULC
When inputs are configured as bond sense and/or general purpose inputs (access control and
burglar installations), remaining inputs cannot be used for fire.
Lock Output Connection
The controller provides a connection for an electric strike lock with full monitoring of the lock circuit for tamper
and over current/fuse blown conditions. The door lock monitoring can be disabled if it is not required.
The lock output is shared with the bell/siren function as shown in the diagram below. You can select another
output for the lock control (Relay 1 (CP001:03) or Relay 2 (CP001:04)) if the bell/siren function is required.
PRT-WX-DIN | Protege WX DIN Rail Integrated System Controller | Installation Manual 20