ICW Elite User manual

1) Do not attempt to adjust your Elite arm until everything you intend to mount to
the arm is mounted.
2) Arm must be completely horizontal (extended) before adjusting the arms tension.
Failure to do so will damage the arm and void the warranty.
3) Never loosen or remove any of the shoulder bolts. Doing so will cause the
arm to immediately come apart with tremendous force, and could cause seri-
ous injury.
4) If equipment requiringAC power is mounted to this unit, have a certified electri-
cian inspect the installation.
5) Failure to install this unit according to these instructions will void all ICW warran-
ties. If installed incorrectly, ICW is not liable for any damage or injury caused by
the unit.
ICWElitewallmountinstallation
DANGER!
The Elite arm contains high pressure gas springs.
The following cautions MUST be observed to
avoid serious injury.
Shoulder bolt

Locate a stud in the wall you intend to mount your arm on
and remove the wall mount from the box. Mark the top
hole, drill 11/64 pilot hole and insert an ICW provided
#14 screw and tighten slightly. Using a level, mark the two
lower holes and drill pilot holes, insert the last two #14
screws and, with the mount level, tighten all screws se-
curely.
Wallmount
Note:ICWsupplies#14 wood screws,ifinstallingontometal studs
youwillneedto replace withpropermetalstudfasteners. All
hardwareused to securewallmountmust have aproper
countersunkhead.
2
The wall mount is shipped
with the bearings wrapped and
it is recommended that you
leave the wrapping on until
later in the installation process.

Nylock
Steel
race
Find the 3/8 bolt assembly in
your hardware bag.
Remove the 4 covers as shown. Removethecenter coverby
unscrewingthe4 10-24 flathead
screwsusingthe 1/8 hexkey.
Removethelongarm
coversbyunscrewing
the2 6-32flathead
screwsusingaphilps
headscrewdriver.
Removetheend
coverby unscrew-
ingthe 210-24
screwsusingthe
1/8hexkey.
Removewrappingfrombearing and place theendofthe
Elitearmonthewallmount.
3

Extendthearmstraightout and lay allofthecables
foryourmonitor,keyboard,andmouseinthe channel
ontop ofthe arm.
Be sure your cables are to one or
theotherside of thecenteradjustment
hub.YOUMUSTLEAVEABITOF
SLACK IN THE CORDSTOALLOW
FORARM MOVEMENT.
Hub
Cable
4
Passthe 3/8 boltwith
thebearingassembly
throughthewallmount
andthearmfrom
underneath. Placethe
steelrace overthe bolt
insidethearmasshown
andsecurefirmlywith
thenylockusingthe
provided9/16wrench
and5milhex key.
Elite arm mounted on wall.
Keepthe armfolded
whileinstalling.

Wiretie your cablestogetherwiththe hub betweenthem.
Wireties arefoundin your hardwarebag.
Addthe wireclips tosecure thecables.
Wireclips are foundinyour hardware bag.
Wireclips
Addthe wire clipto the
endofarm.
Cable
Feedcordthroughtheplasticbushingin
themount assembly. The plasticbushing
canbe removed,opened andslipped
overcordif nessesary.
5
Replace all of the covers. Being sure not to pinch the cables.
The long covers should be replaced first, then the center cover,
and lastly the two end covers.

6
Usethe provided1/4” wrenchto open
theplasticslidermountand insert the
ballontheVESAPlate.Tightenfirmly. Secure yourmonitorto the
VESAplateusingthe4provided
4mmscrews.
Besureto tighten bothbolts
together - not one side and
then the other.
Attachthe keyboard tothe keyboardmount
usingthe supplied screws.

Attachtheoptionallargehandleto
theendoftheslider by screwing
togetherthetwohalves.
Usetheslider handle toadjust
themonitorup and down.
Usethepush
buttonstopivotthe
monitorforward and
back. Liftgentlyon
themonitortorelease
theweight off the buttons.
7

Extend the Elite straight out as shown before adjusting the arms
resistance. Be sure all equipment is mounted on the arm before
adjusting. Adjust the arm closest to the monitor first.
Use the T-handle provided to adjust the arms resistance.
Thank you for your purchase of an ICW Elite arm, your arm is now
ready to use.
Any questions please contact ICW at: 1-800-558-4435.
Before adjusting the tension on your Elite arm place everything
you are going to mount on it in place, including the monitor, key-
board, mouse, and mouse pad.
8