IEI Technology IMBA-Q454 User manual

1

 !""#!!$%&'()*)'
+),'(-!)./0$

IMBA-Q454
Quick Installation Guide
Version 1.0
Feb. 12, 2009
Package Contents
IMBA-Q454 package includes the following items:
1 x IMBA-Q454 Single Board Computer
2 x Dual RS-232 cable with bracket
6 x SATA cable
1 x Mini Jumper Pack
1 x I/O Shielding
1 x Utility CD
1 x QIG (Quick Installation Guide)
©2006 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
CPU: Intel® Core
 !"#$%
System Chipset: Intel® Q45+ ICH10DO
BIOS: AMI BIOS label
System memory: 4 x 240pin Dual-Channel DDR2 800/667 MHz
SDRAM DIMMs support up to 8GB
Ethernet:
PCIe interface Intel® 82567LM GbE controller(iAMT 5.0 support)
PCIe interface Intel® 82574L GbE controller
I/O Interface:
6 x RS-232 (1 on rear, 5 by pin header)
12 x USB2.0 (4 on rear, 8 by pin header)
6 x SATA II support RAID 0, 1, 10, 5
1 x FDD
1 x LPT
1 x PS/2 for KB/MS
Infrared interface: 1 x 5-pin pin header
SPDIF: 1 x 5-pin pin header
Expansion: 1 x PCIe x16 Slot
1 x PCIe x4 Slot
4 x PCI Slot
Super I/O: First Super I/O: ITE IT8718F
Second Super I/O: Fintek F81216
Digital I/O: 8-bit Digital I/O ( 4-bit input / 4-bit output)
Display: Support by Intel® GMA4500 Integrated in Intel® Q45
Analog CRT
Audio: Realtek ALC888 supports 7.1 channel HD Audio Codec
TPM: iTPM1.2
Watchdog timer: Software programmable 1-255 sec. by Second
super I/O: Fintek F81216
Power supply: ATX
Power Consumption:
3.3V@ 2.64A, 5V@ 5.4A, 12V@ 0.28A (Intel® Core™ 2 Duo

3
E8500 3.16GHz with DDR2 800MHz 2GB DRAM x4) 3D Mark
2001SE
Operating Temperature: 0 ~ 60°C( 32 ~ 140°F)
Operating Humidity: 5%~95% non-condensing
Dimension: 305mm x 244mm
Weight: GW:1200g, NW:600g
Ordering Information
IMBA-Q454-R10:
&'( )*+,&--.
 !"#$%*,)/$&'&**0&*
1$%23 4!&
SDVO-100VGA-R10:
PCIex16 VGA output SDVO Card support dual display(IEI board only)
SDVO-100DVI-R10:
PCIex16 DVI output SDVO Card support dual display(IEI board only)
CF-775A-RS: CPU Cooler
CF-520-RS: CPU Cooler
32200-000017-RS: FDD Cable
32100-088600-RS: SATA Power Cable
CB-USB02-RS: Dual Ports USB Cable with Bracket
CB-USB14-RS: 4 Ports USB Cable with Bracket
NOTICE
1) Before removing the DDR2 DRAM module, make sure the AC power is
completely turned off. Incorrect usage may cause permanently damage to
the IMBA-Q454 or the DRAM module. This is because the IMBA-Q454
supports iAMT feature and need to provide power to the DRAM module
when the IMBA-Q454 is off.
2) Do not disconnect the ATX connector when the IMBA-Q454 is powered
on and running. Please make sure to switch off the ATX power supply
prior to disconnect the ATX connector. Incorrect usage may cause
permanently damage to the IMBA-Q454.
3) If the IMBA-Q454 fails to boot due to improper usage, please clear the
CMOS by disconnect the battery from the connector.

4
Jumpers setting and Connectors
LABEL FUNCTION
J_CMOS1 CMOS state setting jumper
KB_MS1 External PS/2 KB/MS Connector
3IN1_DSUB1
External VGA/COM1/LPT connectors
LAN1_USB01
LAN2_USB23
External LAN And USB Connectors
AUDIO_CV1
External Audio Connector
FP_AUDIO1
Front Audio Connector
SPDIF1 Internal SPDIF Connector
COM2 ~ 6 Internal Serial Port Connectors (RS-232)
JSPI1 Flash SPI ROM connector
USB45
USB67
USB89
USB1011
Internal 8 Port USB Connectors
SATA1 ~ 6 Serial ATA Connectors
FDD1 FDD Connector
IR1 Infrared Interface Connector
CPU_FAN1
NB_FAN1 Smart Fan Connectors for CPU and NB
SYS_FAN1 System Fan Connector
DIO1 Digital I/O Connector
F_PANEL1 PWR

RST Buttons

*$45
CPU12V1 ATX-12V CPU Power Source Connector
PCIE_12V1 PCIe Power Source Connector
ATX1 ATX Power Source Connector
BAT1 Coin Battery holder
DIMM1 ~ 4 DDR2 Slots
PCIEX16_1 PCIe x 16 Slot
PCIEX4_1 PCIe x 4 Slot
PCI1 ~ 4 PCI Slot

5
J_CMOS1 : Clear CMOS Setup
J_CMOS1
DESCRIPTION
1-2
(default)*
Keep CMOS Setup
(Normal Operation)
Short 2-3
Clear CMOS Setup
FP_AUDIO1 : Front Audio Connector
PIN NO.
DESCRIPTION PIN NO.
DESCRIPTION
1 MIC_L 2 GND
3 MIC_R 4 Audio Detect
5. LINE Out-R 6 GND
7 Jack Detection 8 N/C
9 LINE Out-L 10 GND
SPDIF1 :
Internal SPDIF connector
PIN
DESCRIPTION
1
5V
2
N/C
3
SPDIFOUT
4
GND
5
SPDIFIN
USB45

 

USB67

 

USB89

 

USB1011 :
Internal USB Connectors
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1 VCC(+5V) 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA-
7 GND 8 VCC(+5V)
IR1: Infrared Interface
Connector
PIN DESCRIPTION
1 VCC(+5V)
2 NC
3 IR-RX
4 GND
5 IR-TX
JTPM1 &JTPM2 : Enable iTPM
JTPM1
JTPM2
DESCRIPTION
Short
(default*)
Short
(default*)
Enable iTPM
Short Open
Open Short
Open Open
Disable iTPM

6
DIO1 : Digital Input / Output Connector
PIN NO.
DESCRIPTION PIN NO.
DESCRIPTION
1 Ground 2 VCC(+5V)
3 Output 3 4 Output 2
5 Output 1 6 Output 0
7 Input 3 8 Input 2
9 Input 1 10 Input 0
COM2 ~ COM6 :
Internal Serial Port Connectors (RS-232)
PIN
DESCRIPTION PIN
DESCRIPTION
1 DCD# 2 DSR#
3 RXD 4 RTS#
5 TXD 6 CTS#
7 DTR# 8 RI#
9 GND 10 NC
CPU_FAN1

 

NB_FAN1:
Smart fan Connectors
PIN NO.
DESCRIPTION
1 Ground
2 +12V
3 Rotation Signal
4 Control
F_PANEL1 : PWR

 

RST Buttons

 

10'/2
PIN
DESCRIPTION
PIN
DESCRIPTION
1 Power LED+
2
Speaker+
3 N/C 4
N/C
Power LED
5 Power LED- 6
N/C
7 PWRBTN+ 8
Speaker-
Speaker
PWRBTN
9 PWRBTN- 10
N/C
11
HDLED+ 12
Reset+
HDDLED
13
HDLED- 14
Reset -
RESET
SYS_FAN1:
fan Connectors
PIN NO.
DESCRIPTION
1 Ground
2 +12V
3 Rotation Signal

7
PCIE_12V1:
PCIe Power Source Connector
PIN NO. DESCRIPTION
1 VCC +5V
2 GND
3 GND
4 VCC +12V
JSPI1 : SPI Flash Connector
PIN NO. DESCRIPTION
PIN NO. DESCRIPTION
1 3.3V 2 GND
3 CS0# 4 CLK
5 SO0 6 SI
7 N/C 8 N/C
CPU12V1 : CPU POWER Source Connector
PIN NO.
DESCRIPTION PIN NO.
DESCRIPTION
1 GND 2 GND
3 +12V 4 +12V
BAT1 :
Coin battery holder
PIN
DESCRIPTION
1 BAT+
2 BAT-(GND)

8
Board Layout: Jumper and Connector Locations