IFM Electronic efector150 KQ6 User manual

Operating instructions
Capacitive sensors
KQ6
704637 / 01 07 / 2009
UK
Q-Pulse Id: VM27

2
Contents
1 Preliminary note........................................................................................ 3
1.1 Symbols used ..................................................................................... 3
2 Safety instructions .................................................................................... 3
3 Functions and features............................................................................. 4
3.1 Application examples.......................................................................... 4
4 Installation ................................................................................................ 5
4.1 Use as a level sensor ......................................................................... 5
4.1.1 Installation on flat tanks with a mounting adapter ...................... 5
4.1.2 Mounting adapter bore hole dimensions.................................... 6
4.1.3 Installation on bybass pipes with a mounting adapter................ 6
4.2 Use as proximity sensor ..................................................................... 7
4.2.1 Installation and installation remarks........................................... 7
4.2.2 Minimum distances .................................................................... 8
4.2.3 Sensor bore hole dimensions..................................................... 8
5 Electrical connection................................................................................. 8
5.1 Wiring.................................................................................................. 9
5.2 Unit versions with auto-detect............................................................. 9
6 Operating and display elements............................................................. 10
7 Settings................................................................................................... 10
7.1 Basic teach empty state.................................................................... 10
7.2 Adjustment teach full state................................................................ 11
7.3 Modified basic teach empty state ..................................................... 12
7.4 Locking / unlocking ........................................................................... 13
8 Operation................................................................................................ 13
9 Maintenance, repair, disposal................................................................. 13
10 Approvals.............................................................................................. 13
11 Terms .................................................................................................... 14
Q-Pulse Id: VM27

3
UK
1 Preliminary note
1.1 Symbols used
Operating elements are indicated as follows:•
Example: [OUT OFF] = Button “OUT OFF“.
An instruction is indicated by “►“.•
Example: ►Mount the unit as shown.
A reaction to the action is indicated by “>“.•
Example: > Yellow LED on.
Important note
Non-compliance can result in malfunctions or interference.
2 Safety instructions
Please read the product description prior to set-up of the unit. Ensure that the•
product is suitable for your application without any restrictions.
The unit conforms to the relevant regulations and EC directives.•
Improper or non-intended use may lead to malfunctions of the unit or to•
unwanted effects in your application.
That is why installation, electrical connection, set-up, operation and•
maintenance of the unit must only be carried out by qualified personnel
authorised by the machine operator.
Q-Pulse Id: VM27

4
3 Functions and features
capacitive sensor used as level or proximity sensor•
detects without contact metals, almost all plastics, glass, ceramics, wood,•
paper, oils, greases, water and all hydrous materials and indicates their
presence by providing a switched signal
automatic adjustment to the medium to be detected by means of programming•
buttons
in level applications the sensor detects the medium through the tank wall (only•
suitable for non-metallic tanks)
3.1 Application examples
Q-Pulse Id: VM27

5
UK
4 Installation
4.1 Use as a level sensor
4.1.1 Installation on flat tanks with a mounting adapter
ABC
2
4
53
6
78
The mounting adapter is to be ordered separately (order no. E12153 pack quantity
1 piece or E12154 pack quantity 10 pieces).
Figure A
Align the sensor (1), the cutouts (3) and (4) must show towards the mounting►
adapter.
Place the sensor with the lower part into the mouting adapter. The sleeves of►
the mounting adapter (2) must engage with the lower cutouts of the sensor (4).
First slightly press the lower part of the sensor.►
When the lower part of the sensor is well placed, completely press the sensor►
into the mounting adapter.
You can hear the sensor snap in.>
Figure B
The catch of the mounting adapter (5) must engage with the sensor.>
Fix the sensor with the enclosed screws (6) to the adapter.►
Figure C
Fix the mounting adapter including the inserted sensor to the tank at the►
requested height using suitable screws (7).
Q-Pulse Id: VM27

6
4.1.2 Mounting adapter bore hole dimensions
24
26 4-3
68
35
39
5-3
47
4-3
Do not place the mounting adapter including inserted sensor in the
immediate vicinity of metallic objects.
4.1.3 Installation on bybass pipes with a mounting adapter
The mounting adapter is to be ordered separately (order no. E12153 pack quantity
1 piece).
Fix the sensor to the bypass at the requested height with common cable ties.►
Insert the cable ties through the existing openings of the mounting adapter and►
tighten them firmly.
Q-Pulse Id: VM27

7
UK
4.2 Use as proximity sensor
4.2.1 Installation and installation remarks
B
4!y!To
B
2
3
C
4!y!To
4
without mounting adapter with mounting adapter
sensing face1:
programming buttons2:
plastic plate3:
Sn: nominal sensing range
(see data sheet)
A: distance = 8 mm
B: width of the mounting
adapter = 36
Align the sensing face (1) to the object. Make sure that the programming but-►
tons (2) remain accessible.
Adhere to the indicated minimum distances to metallic objects opposite and►
beside the sensor (free space).
Non-metallic objects (e.g. plastic fixtures) are allowed within the lateral free►
space.
Fix the sensor with appropriate fixing screws to the designated location.►
If the sensor is installed behind a plastic plate (3), the object will be detected►
through the wall. Depending on the material used and the wall thickness the
sensor characteristics might change slightly. Do not use conductive plastics! If
possible, use thin walls.
Q-Pulse Id: VM27

8
4.2.2 Minimum distances
Installation of several sensors of the same type
B
4!y!To
Sn: nominal sensing range (see data sheet)
A: sensor distance 50 mm
4.2.3 Sensor bore hole dimensions
4-3
24-6
5-4
5 Electrical connection
The unit must be connected by a qualified electrician.
The national and international regulations for the installation of electrical
equipment must be adhered to.
Disconnect power►
Connect the unit►
Q-Pulse Id: VM27

9
UK
5.1 Wiring
CO
CL
CV
M,
M
4
2
35
M,
M
2
5
4
p-switching (type ...FPKG... or ...FPOG...)
BN = brown, BK = black, BU = blue
M
CO
CL
CV
M,M,
M
2
5
4
4
2
35
n-switching (type ...FNKG... or ...FNOG...)
BN = brown, BK = black, BU = blue
5.2 Unit versions with auto-detect
On power up, unit types with auto-detect (types ...FAKG or ...FAOG...) detect
automatically if the output is connected to L- (p switching) or to L+ (n switching).
Disconnect the unit to acknowledge a change of the load connection.►
Automatic load detection is only ensured when a resistor is switched in
series to a closed mechanical contact.
M,
M
2
5
4
M,
M
2
5
4
load detection is possible load detection impossible
Q-Pulse Id: VM27

10
6 Operating and display elements
3
22
1: programming buttons 2: sensing face
7 Settings
7.1 Basic teach empty state
Using the basic teach empty state the unit suppresses the installation environ-
ment. The basic teach empty state resets the unit, an adjustment teach already
carried out is deleted.
Empty the tank until the level is at least 20 mm►
below the sensor.
31!nn
Set the unit as normally open (output closes when the
tank is full):
Press►[OUT OFF] for min. 2 s (max. 6 s).
While pressing the pushbutton the LED flashes>
slowly. After releasing the pushbutton, the LED
goes out. 2 - 6 s
Set the unit as normally closed (output opens when
the tank is full):
Press►[OUT ON] for min. 2 s (max. 6 s).
While pressing the pushbutton the LED flashes>
slowly. After releasing the pushbutton, the LED
lights continuously. 2 - 6 s
The unit is now ready for operation. For the detection of media with a low dielectric
constant (e.g. plastic granulates or oils) no further setting is required.
Q-Pulse Id: VM27

11
UK
7.2 Adjustment teach full state
Necessary for aqueous media. The sensitivity of the unit is optimised. Later on,
the adjustment teach full state can be repeated at any time, an adjustment teach
empty state already carried out is not affected.
A basic teach empty state must be carried out prior to the adjustment teach
full state (→chapter 7.1 Basic teach empty state)! If it is not possible to empty
the tank, a basic teach empty state can be carried out by simulating the empty
state (e.g. adjustment when not installed, adjustment at a higher position). For
optimum function it is necessary to carry out the “modified basic teach empty
state“ (→chapter 7.3 Modified basic teach empty state) when the tank is
emptied the next time.
Fill the tank until the sensing face of the unit is►
covered.
For NO the LED lights, for NC it goes out.>
Set the unit as normally open (output closes when the
tank is full):
Press►[OUT ON] for min. 6 s.
While pressing the pushbutton the LED first flashes>
slowly, after 6 s more quickly. After releasing the
pushbutton, the LED lights continuously. > 6 s
Set the unit as normally closed (output opens when
the tank is full):
Press►[OUT OFF] for min. 6 s.
While pressing the pushbutton the LED first flashes>
slowly, after 6 s more quickly. After releasing the
pushbutton, the LED goes out. > 6 s
Q-Pulse Id: VM27

12
7.3 Modified basic teach empty state
Recommended for deposits in the tank. Deposits are largely suppressed. This is
also recommended if it has not been possible to carry out a basic teach empty
state (e.g. if the sensor is set up on a full tank; details: →chapter 7 Adjustment
teach full state)
Later on, the modified basic teach empty state can be repeated at any time, an
adjustment teach full state already carried out is not affected.
Empty the tank until the level is below the sensing►
face of the unit.
For NO the LED goes out, for NC the LED lights.>
Set the unit as normally open (output closes when the
tank is full):
Press►[OUT OFF] for min. 6 s.
While pressing the pushbutton the LED first flashes>
slowly, after 6 s more quickly. After releasing the
pushbutton, the LED goes out. > 6 s
Set the unit as normally closed (output opens when
the tank is full):
Press►[OUT ON] for min. 6 s.
While pressing the pushbutton the LED first flashes>
slowly, after 6 s more quickly. After releasing the
pushbutton, the LED lights continuously. > 6 s
Q-Pulse Id: VM27

13
UK
7.4 Locking / unlocking
The unit can be electronically locked to protect it against unintentional setting.
To lock press [►OUT ON] and [OUT OFF]simulta-
neously for 10 s.
Acknowledgement: LED state (yellow) changes for>
a short time (the lit LED goes out briefly or the LED
which is not lit lights briefly).
To unlock repeat this step.►10 s
If the unit does not react, it may be locked.
8 Operation
Check whether the unit operates correctly. Bring about a sensor response by
taking suitable measures.
Display by LEDs (indepedent of the programmed output function):
LED yellow OFF:
LED yellow ON:
switching output disabled
switching output enabled
9 Maintenance, repair, disposal
The operation of the unit is maintenance-free. To ensure a correct function:
Keep the sensing face and a clear space, if any, free from deposits and foreign•
bodies.
When replacing the sensor ensure that installation is done in the same way and a
sensor with the same settings is used.
It is not possible to repair the unit.
After use dispose of the unit in an environmentally friendly way in accordance with
the applicable national regulations.
10 Approvals
The device shall be supplied from an isolating transformer having a secondary
Listed fuse rated either
a) max 5 amps for voltages 0~20 Vrms (0~28.3 Vp) or
b) 100 / Vp for voltages of 20~30 Vrms (28.3~42.4 Vp)
Q-Pulse Id: VM27

14
11 Terms
Active zone
Area above the sensing face in which the sensor reacts to the approach of the
target.
Output function
Normally open: object within the active zone - output switched.
Normally closed: object within the active zone - output blocked.
Programmable: Choice between normally closed or normally open.
Positive switching: positive output signal (to L-).
Negative switching: negative output signal (to L+).
Power-on delay time
The time the sensor needs to be ready for operation after application of the
operating voltage (in the millisecond range).
Hysteresis
Difference between the switch-on and the switch-off point.
Leakage current
Current for the internal supply of 2-wire units, also flows through the load when the
output is blocked.
Current consumption
Current for the internal supply of 3-wire DC units.
Switch point drift
Shifting of the switch point owing to changes of the operating conditions (e.g.
temperature, pressure, air humidity).
Short-circuit protection
ifm sensors which are protected against excessive current by means of a pulsed
short-circuit protection. The inrush current of incandescent lamps, electronic relays
and low resistance loads may cause this protection to cut in and turn the sensor
off!
Operating voltage
The voltage range in which the sensor functions safely. A stabilised and smoothed
direct voltage should be used! Take into account residual ripple!
Q-Pulse Id: VM27

15
UK
Technical data and further information at
www.ifm.com →Select your country →Data sheet direct:
Q-Pulse Id: VM27