NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
6
Figure 4 Figure 5
NEW CONSTRUCTION OR RENOVATION
1. Select alocation that is not proneto moisture
and is located at least 3 feet (or 0.9m) away
from combustible materials such as curtains
or drapes, furniture, bedding, paper, etc.
2. Place the unit in selected location to see how
it will look in the future.
3. Mark the desired location on the floor and
storeunit in asafe, dry anddust freelocation.
4. Frame in an opening leaving at least 1/4"
(6mm) around the edge of the unit. Any
new wiring must be done in compliance with
local and national codes and other applicable
regulations in order to reduce the risk of fire,
electric shock or other injuries. Therefore,
it is strongly recommended that you hire a
professional to complete any such work.
INSTALLING THE FIREPLACE INSERT
1. Once thesite hasbeen prepared,the fireplace
insert can be installed.
2. Make sure the switch is in the "OFF" position.
3. Plug the fireplace into a 15-amp/120 volt,
grounded outlet.
4. Push the fireplace insert so that the trim is
against the finished mantel or wall surface.
WARNING
GRILLS ON THIS ELECTRIC FIRE-
PLACE CANNOT, IN ANY WAY, BE
COVERED AS IT MAY CREATE A
FIRE HAZARD.
NOTE: Power supply service must be complete
prior to finishing, to avoid reconstruction.
Grills and air openings cannot be covered in
any circumstances.
OPERATING INSTRUCTIONS
1. Plug in your electric fireplace.
2. Main ON/OFF Power switch: This switch
is located on the right side of the control
panel (see Figure 4). When the unit is on,
the default settings for the fireplace is HI
ember bed and flame and the heater is OFF.
3. Temperature Control button and LED: This
button is located to the left of the Remote
Control Receiver (see Figure 4). The LED
is located to the left of the Flame Button.
Push button to cycle through the settings.
When this button is pushed, the LED will
change to its corresponding color; Green
for LO, Orange for MED, and Red for HI.
When heater is on, heat will emit through
vents located above the firebox opening
panel (see Figure 6, Page 7).
Flame Control
Button ON/OFF Power
Button
Temperature
LED
Temperature
Control Button
Remote Control
Receiver
FL TM
The heater has abuilt in thermostatso it will shut
off automatically once the set temperature is
reached. It will also turn on automatically if
the room temperature drops below the set
temperature.
NOTE: When the heater is turned on for the
first time, it may release a slight, harmless odor.
This odor is a normal occurrence caused by the
initial heating of the internal heating elements
and should not occur again.
4. Flame Control button: This button is located
to the left of the Temperature Button (see
Figure 4). After power is on, push the
Flame Control Button to adjust flame and
ember bed brightness. Press and release
the Flame Control Button to cycle through
LO, MED, HI and OFF.
OPERATING BY REMOTE CONTROL
(see Figure 5)
1. To control the electric fireplace by remote
control, the main power on/off switch
should be in the off position. This switch is
located on the front left floor of firebox (see
Figures 4 & 5).
2. When operating the remote control, it must
be pointed at the logs inside the electric
fireplace and a beep must be heard each time
you press a function button. The beep lets
you know the remote control is operating the
function button you are pressing.
3. Remote On/Off Button - The button on the
top left (see A) is the on/off power button.
When pressing this button you will hear
a beep, this will activate the power to the
fireplace. You must then press the display
button (C) to activate the lights.
4. To increasethe brightness,press andrelease
the light brighten button (see E). Each time
you press this button you will hear a beep,
and the brightness will increaseslightly until
the maximum brightness is achieved. To
decrease the brightness, press and release
the light dimming button (see D). Each time
you press this button you will hear a beep,
and the brightness will decrease slightly
until the minimum brightness is achieved.
5. Heater Button - Press this button and the
heater will operate at 1900W (F). If pressed
again, the heater will turn off.
6. Temp - Press this button (I) to automatically
control room temperature.
HIGH (H), or LO (G). The heater is preset
to the following temperatures:
• HIGH heater works at 1900W
• LO heater works at 950W6.
7. If a yellow flame is desired, press and
releasethe (K)button until thedesired flame
color is reached. Each time the button is
depressed, you will hear a beep and the
flame will change from blue to yellow until
the maximum setting is reached. If a blue
flame is desired, press and release the (J)
button until the desired color is reached.
7. To turn the electric fireplace off, Press the On/
Off button once (A), when you hear the beep
the fireplace will be completely off. When you
restart your fireplace with the remote control,
all settings will restart at the high settings pro-
grammed at the factory. You may also simply
press the (C) button to turn off the flame and
still use the heater.
NOTE:Make sure your batteries are fullycharged
and installed correctly in your remote control.
A
D
F
H
G
J
CB
E
I
K
