Ikan PT3700-TK User manual

PT3700-TK
PT3700 Teleprompter & Hard Case Travel Kit
QUICKSTART GUIDE
Checked by
www.ikancorp.com
CONDITIONS OF WARRANTY SERVICE
• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
• The components and maintenance service fee will be charged if the warranty period has expired.
Free Service will not be Provided in the Following Situations: (* Even if the product is still within the warranty period.)
• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
• Damage caused by natural disaster, abnormal voltage, and environmental factors etc.
1.713.272.8822
[e-mail]
©2014ikanCorporation.Allrightreserved
QUICKSTART GUIDE

PT3700-TK
QUICKSTART GUIDE
PT3700 Teleprompter & Hard Case Travel Kit
What’s included
www.ikancorp.com 713-272-8822
Teleprompter Frame
Assembly with Monitor
Camera Mount
Assembly
18"Rods x2Hood 200mm Riser
Rods x2
PrompterPro Software


  


5/32 Hex Key Cork Strips x 4
 DRS-01 x 2
PT-CASE


PT3700-TK
QUICKSTART GUIDE
PT3700 Teleprompter & Hard Case Travel Kit
713-272-8822
www.ikancorp.com
Place teleprompter
frame assembly on a at
surface and slide the 18
in. rods into rod mounts.
Rod Mounts
You can position the
glass at any angle you
want but the preferable
angle is 45°
STEP 1:
STEP 2:

PT3700-TK
QUICKSTART GUIDE
PT3700 Teleprompter & Hard Case Travel Kit
713-272-8822
www.ikancorp.com
The tripod mount has 3
sets of holes that allow
you to mount the plate
either towards the front or
rear to help balance the
telepromter better.
For larger cameras its is
better to have the plate
toward the rear and for
smaller cameras towards
the front.
STEP 3:
Slide the Camera Mount
Assembly onto the 15mm
Rods.

Use the included
5/32 Hex Key to
remove and attach
the Raiser Rods.
PT3700-TK
QUICKSTART GUIDE
PT3700 Teleprompter & Hard Case Travel Kit
713-272-8822
www.ikancorp.com
Attach camera to
camera mount and
slide to best position.
Make sure all thumb
screws are secure.
If you require the camera to
be positioned higher you
can replace the 200mm
raiser bars in place of the
pre-installed 130mm Rods.
STEP 4:
DSLR CAMCORDER

PT3700-TK
QUICKSTART GUIDE
PT3700 Teleprompter & Hard Case Travel Kit
713-272-8822
www.ikancorp.com
Attach hood to glass frame
using the integrated
magnets. You can attach
the optional side aps.
STEP 5:

PT3700 Teleprompter & Hard Case Travel Kit
Checked by
www.ikancorp.com 713-272-8822
Glass can be removed from
the frame by removing the
two phillip head screws.
Easily slide the glass out
of the frame.
*You should only need to do this for cleaning*
PT3700-TK
QUICKSTART GUIDE

Monitor Ports
BNC – AV Composite Input
VGA – Video Graphics Array DE15 Connection
HDMI – High-Definition Multimedia Interface Input Connection
Power Port – 12-24v Input
HDMI – Switch HDMI input
VGA – Switch to VGA input
AV – Switch to composite BNC input
Flip – Toggle image flip
(Can be set to horizontal, vertical, or both via menu)
Up Arrow – Toggle up to adjust setting
Menu – Access to monitor settings
Down Arrow – Toggle down to adjust setting
Monitor Menu Settings
Video Config
Contrast (White Level)
Brightness (Black Level)
Tint (Chroma Hue)
Chroma (Chroma Saturation)
Sharpness (Detail)
RGB Setup – Manually configure RGB
Return
System Config
Menu Duration – Set duration of how long menu stays
on screen
Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is
native resolution, 16:9 will create black bars)
Flip-H – Assign toggle button to flip image horizontally
Flip-V – Assign toggle button to flip image vertically
Reset – Factory reset
Return
PC Setup (Only available for VGA)
H-Position – Adjust horizontal position
V-Position – Adjust vertical position
Auto – Monitor automatically adjust position
Return
Exit
HDMI
How to set-up FLIP button feature:
1. Press MENU button
2. Navigate to SYSTEM CONFIG.
3. Navigate to FLIP-V or FLIP-H
4. Change FLIP-V and/or FLIP-H to “ON”
5. Exit MENU
6. The FLIP button should now be activated and can be
pressed to mirror the image Horizontally or Vertically
7. When FLIP-H is ON, the image will flip Horizontally
8. When FLIP-V is ON, the image will flip Vertically
9. If both are ON, the FLIP button will toggle both
Horizontal and Vertical flip