IKEA LBZ8C Product information sheet

+
LUFTIG
30" (76.2 CM) RANGE HOOD
Installation Instructions and Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-866-664-2449.
In Canada, for assistance, installation and service, call: 1-866-664-2449.
CAMPANA PARA COCINA DE 30" (76,2 CM)
Instrucciones de instalación y Manual de uso y cuidado
Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico, llame al: 1-866-664-2449.
HOTTE D’ASPIRATION DE 30" (76,2 CM)
Instructions d’installation et Guide d’utilisation et d’entretien
Au Canada, pour assistance, installation ou service, composez le 1-866-664-2449.
Table of Contents/Índice/Table des matières..................................................................2
For warranty concerns, do not take the appliance back to the store. Please contact us in U.S.A. or Canada at 1-866-664-2449.
This product features a Limited Warranty - See the “Warranty” section for complete details. IKEA®appliances carry a 5-year
warranty (excludes LAGAN family - see warranty for coverage details).
NOTE: Proof of Purchase is required to obtain warranty service.
Si tiene dudas acerca de la garantía, no devuelva el aparato a la tienda. Póngase en contacto con nosotros en los EE.UU. o en
Canadá al 1-866-664-2449.
Este producto tiene una garantía limitada - Consulte la sección “Garantía” para obtener todos los detalles. Los aparatos IKEA®
tienen una garantía de 5 años (excluyendo los de la familia LAGAN - consulte la garantía para ver los detalles acerca de la
cobertura).
NOTA: Se requiere la prueba de compra para obtener servicio bajo la garantía.
Pour toute question concernant l’application de la garantie, ne pas rapporter l’appareil au magasin. Veuillez nous contacter aux
É.-U. ou au Canada au 1-866-664-2449.
Ce produit est couvert par une garantie limitée – Voir la section “Garantie” pour des détails complets. Les appareils IKEA®sont
couverts par une garantie de 5 ans (hormis les appareils de la série LAGAN - voir la garantie pour des détails concernant les
modalités de garantie).
REMARQUE : Une preuve d’achat est obligatoire pour obtenir l'application de la garantie.
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
FOR RESIDENTIAL USE ONLY.
IMPORTANTE: LEAY GUARDE ESTAS INSTRUCCIONES.
SÓLO PARA USO RESIDENCIAL.
IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.
POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.
LBZ8C/W10722651B

2
TABLE OF CONTENTS
RANGE HOOD SAFETY .................................................................3
INSTALLATION REQUIREMENTS................................................5
Tools and Parts ............................................................................5
Location Requirements................................................................5
Venting Requirements..................................................................6
Electrical Requirements ...............................................................7
INSTALLATION INSTRUCTIONS..................................................8
Prepare Location..........................................................................8
Install Range Hood.....................................................................10
Make Electrical Connection .......................................................12
Complete Installation .................................................................13
RANGE HOOD USE......................................................................13
Range Hood Controls.................................................................13
RANGE HOOD CARE ...................................................................13
Cleaning......................................................................................13
WIRING DIAGRAM .......................................................................14
ASSISTANCE OR SERVICE.........................................................15
In the U.S.A. ...............................................................................15
In Canada ...................................................................................15
Accessories ................................................................................15
WARRANTY ..................................................................................16
ÍNDICE
SEGURIDAD DE LA CAMPANA PARA COCINA .......................18
REQUISITOS DE INSTALACIÓN.................................................20
Herramientas y piezas................................................................20
Requisitos de ubicación.............................................................20
Requisitos de ventilación ...........................................................21
Requisitos eléctricos..................................................................23
INSTRUCCIONES DE INSTALACIÓN.........................................23
Preparación de la ubicación ......................................................23
Instalación de la campana para cocina.....................................26
Conexión del suministro eléctrico..............................................28
Complete la instalación..............................................................28
USO DE LA CAMPANA PARA COCINA .....................................28
Controles de la campana para cocina.......................................28
CUIDADO DE LA CAMPANA PARA COCINA............................29
Limpieza .....................................................................................29
DIAGRAMA DE CABLEADO........................................................30
AYUDA O SERVICIO TÉCNICO...................................................31
En los EE.UU. .............................................................................31
Accesorios..................................................................................31
GARANTÍA.....................................................................................31
TABLE DES MATIÈRES
SÉCURITÉ DE LA HOTTE............................................................33
EXIGENCES D'INSTALLATION...................................................35
Outils et pièces...........................................................................35
Exigences d'emplacement.........................................................35
Exigences concernant l’évacuation...........................................36
Spécifications électriques..........................................................37
INSTRUCTIONS D’INSTALLATION ............................................38
Préparation de l'emplacement...................................................38
Installation de la hotte................................................................40
Raccordement électrique...........................................................43
Achever l’installation ..................................................................43
UTILISATION DE LA HOTTE .......................................................44
Commandes de la hotte.............................................................44
ENTRETIEN DE LA HOTTE..........................................................44
Nettoyage ...................................................................................44
SCHÉMA DE CÂBLAGE...............................................................45
ASSISTANCE OU SERVICE.........................................................46
Au Canada..................................................................................46
Accessoires ................................................................................46
GARANTIE.....................................................................................46

3
RANGE HOOD SAFETY
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.

4
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS

5
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■Drill
■1¹⁄₄" (3.0 cm) drill bit
■¹⁄₈" (3.0 mm) drill bit for pilot holes
■Pencil
■Wire stripper or utility knife
■Tape measure or ruler
■Caulking gun and weatherproof caulking compound
■Flat-blade screwdriver
■Phillips screwdriver
■Saber or keyhole saw
■Metal snips
■Compass or 8" (20.3 cm) circle template
Parts supplied
Remove parts from package. Check that all parts are included.
■2 - 3.5 x 9.5 mm screws
■3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vent damper
■7" (17.8 cm) round vent mounting plate
■T10 Torx®† adapter
■4 - 4.5 x 13 mm mounting screws
Parts needed
■1 - 75W max, 120V light bulb
■Wall or roof cap with damper to match vent system
■3 - UL listed wire connectors
■Vent clamps/duct tape as required
For IKEA SEKTION 15" (38.1 cm) deep cabinets
■30" (76.2 cm) extension panel (IKEA part number 302-822-39,
see the “Assistance or Service” section to order).
■3 - mounting screws and mounting hardware (purchased
separately). Be sure to purchase screws and hardware
appropriate for use with your type of wall.
For cabinets with recessed bottoms:
■Two 2" (5.1 cm) wide filler strips. Length and thickness
determined by recess dimensions.
■Four flat head wood screws or machine screws with washers
and nuts (to attach filler strips).
For 7" (17.8 cm) round vented installations:
■7" (17.8 cm) round metal vent system
For 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vented installations:
■3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular metal vent system
For non-vented (recirculation) installations:
■Charcoal filter kit. For information on ordering, see the
“Accessories” section.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located inside the range hood on
the left wall.
■Range hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
■Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range manufacturer installation instructions before
making any cutouts.
■Grounded electrical outlet is required. See “Electrical
Requirements” section.
■All openings in ceiling and wall where range hood will be
installed must be sealed.
■These range hoods are factory set for vented installations.
Models that are capable of being installed as non-vented
(recirculating) require charcoal filters. See the “Accessories”
section to order charcoal filter kit.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
†®TORX is a registered trademark of Acument Intellectual Properties, LLC.
1"
(2.5 cm)
4¹⁵⁄₁₆"
(12.5 cm)
6⁹⁄₁₆" (16.7 cm)
29¹⁵⁄₁₆" (76.0 cm)
18⁵⁄₈"
(47.3 cm)
1¹⁄₂"
(3.8 cm)
9"
(22.9 cm)
2"
(5.1 cm)
⁷⁄₈"
(2.2 cm)

6
Installation Clearances
Venting Requirements
■Vent system must terminate to the outdoors, except for non-
vented (recirculating) installations.
■Do not terminate the vent system in an attic or other enclosed
area.
■Do not use a 4" (10.2 cm) laundry-type wall cap.
■Use a 7" (17.8 cm) round metal vent or a 3¹⁄₄" x 10" (8.3 x
25.4 cm) rectangular metal vent, depending on your
installation requirements. Rigid metal vent is recommended.
Plastic or metal foil vent is not recommended.
■The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
For the most efficient and quiet operation:
■Use no more than three 90° elbows.
■Make sure there is a minimum of 24" (61 cm) of straight vent
between the elbows if more than 1 elbow is used.
■Do not install 2 elbows together.
■Use clamps or duct tape to seal all joints in the vent system.
■The vent system must have a damper. If roof or wall cap has a
damper, do not use damper supplied with the range hood.
■Use caulking to seal exterior wall or roof opening around the
cap.
Cold Weather Installations
An additional back draft damper should be installed to minimize
backward cold air flow and a thermal break should be installed to
minimize conduction of outside temperatures as part of the vent
system. The damper should be on the cold air side of the thermal
break.
The break should be as close as possible to where the vent
system enters the heated portion of the house.
Makeup Air
Local building codes may require the use of makeup air systems
when using ventilation systems greater than specified CFM of air
movement. The specified CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in your
area.
Venting Methods
Vent system can terminate either through the roof or wall. Use
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular with a maximum vent
length of 35 ft (10.7 m) or 7" (17.8 cm) or larger round vent with a
maximum length of 50 ft (15.2 m) for vent system.
NOTE: Flexible vent is not recommended. Flexible vent creates
both back pressure and air turbulence that greatly reduce
performance.
A. 18" (45.7 cm) min. clearance - upper cabinet to countertop
B. 24" (61.0 cm) minimum - bottom of range hood to cooking
surface
C. 30" (76.2 cm) min. cabinet opening width
D. 12" (30.5 cm) minimum cabinet depth
E. 36" (91.4 cm) base cabinet height
A
B
C
D
E
Roof Venting Wall Venting
A. 7" (17.8 cm) round vent
through roof
(purchased separately)
3
¹⁄₄ " x 10" (8.3 x 25.4 cm)
rectangular vent through the
roof (purchased separately)
B. Roof cap with damper
(purchased separately)
C. 24" (61.0 cm) min. above the
cooking surface
A. 7" (17.8 cm) round vent out the
top and through the wall
(purchased separately)
3
¹⁄₄ " x 10" (8.3 x 25.4 cm)
rectangular vent through the
wall or out the top (purchased
separately)
B. Wall cap with damper
(purchased separately)
C. 24" (61.0 cm) min. above the
cooking surface
A
B
C
A
B
C

7
Calculating Vent System Length
To calculate the length of the system you need, add the
equivalent feet (meters) for each vent piece used in the system.
7" (17.8 cm) Round Vent System
Example Vent System
3¹⁄₄" x 10" (8.3 cm x 25.4 cm) Vent System
Example Vent System
Electrical Requirements
Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70 (latest
edition), or CSA Standards C22.1-94, Canadian Electrical Code,
Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes
and ordinances.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
Vent Piece Round
45° elbow 2.5 ft
(0.8 m)
90° elbow 5.0 ft
(1.5 m)
7" (17.8 cm) wall cap 0.0 ft
(0.0 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)
to 7" (17.8 cm) 4.5 ft (1.4 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)
to 7" (17.8 cm) 90° elbow 5.0 ft (1.5 m)
Maximum Recommended Length = 50 ft (15.2 m)
1 - 90° elbow = 5.0 ft (1.5 m)
1 - wall cap = 0.0 ft (0.0 m)
8 ft (2.4 m) straight = 8.0 ft (2.4 m)
Length of 7" (17.8 cm) system = 13.0 ft (3.9 m)
Wall cap
7" (17.8 cm) round
90˚ elbow
2 ft (0.6 m)
6 ft (1.8 m)
Vent Piece
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)
90° elbow 5.0 ft (1.5 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)
flat elbow 12.0 ft (3.7 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)
wall cap 0.0 ft (0.0 m)
Maximum Recommended Length = 35 ft (10.7 m)
1 - 90° elbow = 5.0 ft (1.5 m)
8 ft (2.4 m) straight = 8.0 ft (2.4 m)
1 - wall cap = 0.0 ft (0.0 m)
Length of 3¹⁄₄" x 10" (8.3 cm x 25.4 cm)
system = 13.0 ft (3.9 m)
Wall cap
3¹⁄₄" x 10"
(8.3 x 25.4 cm)
elbow
2 ft
(0.6 m)
6 ft (1.8 m)

8
■A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is
required.
■If the house has aluminum wiring, follow the procedure
below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
■Wire sizes and connections must conform with the rating of
the appliance as specified on the model/serial rating plate.
The model/serial plate is located behind the filter on the rear
wall of the range hood.
■Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA
Standards C22. 1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition) and all local codes and
ordinances.
INSTALLATION INSTRUCTIONS
Prepare Location
NOTE: It is recommended that the vent system be installed
before hood is installed.
Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
1. Disconnect power.
2. Depending on your model, determine which venting method
to use: roof, wall or non-vented (recirculating).
3. Select a flat surface for assembling the range hood. Place
covering over that surface.
4. Lift the range hood and set it upside down onto covered
surface.
5. If cabinet has recessed bottom, add wood filler strips on each
side. Install screws to attach filler strips in locations shown.
Determine Wiring Hole Location
Cut only one 1¹⁄₄" (3.2 cm) diameter wiring access hole.
1. Determine and clearly mark a vertical centerline on the wall
and cabinet in the area the vent opening will be made.
To wire through top:
1. Mark a line 8³⁄₈" (21.3 cm) from the right of the centerline on
the underside of the cabinet. For 12" (30.5 cm) deep
cabinets, mark the point on this line that is 2"(5.1cm)from
back wall. For 15" (38.1 cm) deep cabinets, mark the point on
this line that is 5³⁄₈" (13.7 cm) from the back wall. Drill a 1¼"
(3.2 cm) diameter hole through the cabinet at this point.
To wire through wall:
1. Mark a line distance “A” from the right of the centerline on the
underside of the wall. Mark the point on this line that
is ⁷⁄₈" (2.2 cm) from the underside of the cabinet. Drill a
1¹⁄₄" (3.2 cm) diameter hole through the rear wall at this point.
A. Centerline
Cabinet
bottom
Wall
3" (7.6 cm)
Wood filler strips
(recessed cabinet
bottoms only)
3" (7.6 cm)
A
A. 8 ³⁄₈ " (21.3 cm)
Centerline
*2" (5.1 cm) for
12" (30.5 cm)
deep cabinets
*5³⁄₈" (13.7 cm) for
15" (38.1 cm)
deep cabinets
*from wall,
not cabinet
frame
A
Centerline
⁷⁄₈" (2.2 cm)

9
Style 1 - Cut Openings for 3¼" x 10" (8.3 cm x 25.4 cm)
Rectangular Vent System
Roof Venting
To make a 4¹⁄₄" x 10½" (10.8 cm x 26.7 cm) rectangular cutout
on the underside of cabinet top and bottom:
1. Mark lines distance “A” and distance “B” from the back wall
on the centerline of the underside of cabinet.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the underside of cabinet.
3. Use saber or keyhole saw to cut a rectangular opening for vent.
4. Repeat steps 1-3 for the underside of the top of the cabinet.
Wall Venting
To make a 3½" x 10½" (8.9 cm x 26.7 cm) rectangle in the
wall:
1. Make 2 lines by measuring ³⁄₈" (0.9 cm) and 3⁷⁄₈" (9.8 cm)
down from underside of cabinet and mark on the centerline
on the back wall.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the wall.
3. Use saber or keyhole saw to cut a rectangular opening in the
wall for the vent.
Style 2 - Cut Openings for 3¼" x 10" (8.3 x 25.4 cm)
Rectangular Vent to Round Vent Transition
Roof Venting
To make a 4¹⁄₄" x 10½" (10.8 cm x 26.7 cm) rectangular cutout
on the underside of cabinet bottom:
1. Mark lines distance “A” and distance “B” from the back wall
on the centerline of the underside of cabinet.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the underside of cabinet.
3. Use saber or keyhole saw to cut a rectangular opening for vent.
To make a circular vent opening on the underside of the
cabinet top:
1. Mark a centerline on the underside of the top of cabinet.
2. Mark a line distance “A” from the back wall on the underside
of the top of cabinet.
3. Use a compass or a circle template to draw a circle with a
diameter that is ¼" (0.64 cm) larger than the vent.
4. Use saber or keyhole saw to cut the circular vent opening.
A. ¹⁄₂ "(1.3 cm) for 12" (30.5 cm) deep cabinets
3 ⁷⁄₈ "(9.8 cm) for 15" (38.1 cm) deep cabinets
B. 4
³⁄₄ " (12.1 cm) for 12" (30.5 cm) deep cabinets
8 ¹⁄₈ "(20.6 cm) for 15" (38.1 cm) deep cabinets
*From wall, not cabinet frame
Cabinet cutouts
*A
*B
2¾"
6¾"
Cabinet
front
(7.0 cm)
(17.1 cm)
5¹⁄₄"
(13.3 cm)
Centerline
5¹⁄₄"
(13.3 cm)
A. ¹⁄₂ "(1.3 cm) for 12" (30.5 cm) deep cabinets
3 ⁷⁄₈ "(9.8 cm) for 15" (38.1 cm) deep cabinets
B. 4
³⁄₄ " (12.1 cm) for 12" (30.5 cm) deep cabinets
8 ¹⁄₈ "(20.6 cm) for 15" (38.1 cm) deep cabinets
A. 5"(12.7 cm) for 12" (30.5 cm) deep cabinets
8
³⁄₈ "(21.3 cm) for 15" (38.1 cm) deep cabinets
*B
*From wall, not cabinet frame
*A
Circular vent opening
Cabinet
cutouts
*From wall, not
cabinet frame
*A

10
Style 3 - Cut Openings for 7" (17.8 cm) Round Vent
To make a circular vent openings on the underside of the
cabinet top and bottom:
1. Mark a centerline on the underside of the top of cabinet.
2. Mark a line distance “A” from the back wall on the underside
of the top and bottom of cabinet.
3. Use a compass or a circle template to draw a circle with a
diameter that is ¼" (0.64 cm) larger than the vent.
4. Use saber or keyhole saw to cut the circular vent opening.
Install Extension Panel for 15" (38.1 cm) Deep Cabinets
IMPORTANT: For 15" (38.1 cm) deep cabinets, an IKEA
®
extension
panel is required. See the “Assistance or Service” section to order
the IKEA
®
30" (76.2 cm) extension panel (IKEA
®
part number 302-
822-39).
1. Install the extension panel to the wall, use 3 screws and
hardware (purchased separately) appropriate for your type of
wall. Use the installation instructions that come with the
extension panel.
Install Vent System
1. Install vent through the vent opening in upper cabinet or wall.
Complete venting system according to the selected venting
method. See “Venting Requirements” section.
2. Use caulking to seal exterior wall or roof opening around the
cap.
Install Range Hood
1. Remove the 7" (17.8 cm) round vent mounting plate and the
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vent damper on the
inside your range hood.
2. Lift the range hood up under cabinet and determine final
location by centering beneath cabinet. Mark on the underside
of cabinet the location of the 4 keyhole mounting slots on the
range hood. Set range hood aside on a covered surface.
3. Use ¹⁄₈" (3 mm) drill bit and drill 4 pilot holes as shown.
4. Install the 4 - 4.5 mm x 13 mm mounting screws in pilot
holes. Leave about ¹⁄₄" (6.4 mm) space between screw heads
and cabinet to slide range hood into place.
A. 5"(12.7 cm) for 12" (30.5 cm) deep cabinets
8 ³⁄₈ "(21.3 cm) for 15" (38.1 cm) deep cabinets
*From wall, not
cabinet frame
*A
A. 7" (17.8 cm) round vent mounting plate
B. Screws
C. 3
¹⁄₄ " x 10" (8.3 x 25.4 cm) rectangular vent damper
A. Keyhole slot
A. Drill pilot hole.
A
B
C
A
A
¹⁄₄"
(6.4 mm)

11
5. Remove vent knockouts depending on your installation
requirements.
Round vent system installations - Remove top rectangular
and round vent knockouts.
Rectangular vent system installations - For roof
installations, remove the top rectangular vent knockout. For
wall installations, remove the rear rectangular vent knockout.
Non-vent (recirculating) installations - Do not remove any
knockouts.
6. Install 7" (17.8 cm) round vent mounting plate or 3¹⁄₄" x 10"
(8.3 x 25.4 cm) vent damper, depending on your vent system
installation. Attach to range hood with 3.5 x 9.5 mm screws
provided.
NOTE: An optional 7" (17.8 cm) round damper is also
available as an accessory. For information on ordering, see
the “Accessories” section.
NOTE: The 7" (17.8 cm) round vent mounting plate and
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vent connector can
be installed up to 1" (2.5 cm) on either side of the hood
center to accommodate off center ductwork.
■If a vent damper is installed with a wall cap with damper,
check that they do not interfere with each other. Remove
the vent connector damper flap if they interfere.
■Non-vented (recirculating) installations - No vent
attachments. Removal of the recirculation cover plate is
required. Remove the two screws from the recirculation
cover plate and remove.
A. Round vent knockout
B. Top rectangular vent knockout
C. Rear rectangular vent knockout
A. 7" (17.8 cm) round damper
(see “Accessories” section)
B. 3.5 x 9.5 mm screws
C. 7" (17.8 cm) round vent mounting plate
D. Round vent knockout
E. Rectangular vent knockout
A
B
C
A
B
C
D
E
A. Vertical connector
B. 3.5 x 9.5 mm screws
C. Vent knockouts
D. Horizontal connector
A. Screws
B. Recirculation cover plate
B
A
B
D
C
A
B

12
Power Supply Cable Installation
1. For direct wire installations, run the home power supply cable
according to the National Electric Code or CSA standards
and local codes and ordinances. There must be enough
wiring from the fused disconnect (or circuit breaker) box to
make the connection in the hood electrical terminal box.
For optional power supply cord kit (see “Accessories”
section), follow the instructions in the “Make Electrical
Connections” section.
NOTES:
■Use only with range hood cord connection kits that have
been investigated and found acceptable for use with this
model range hood.
■Do not reconnect power until the installation is complete.
2. Remove the screws from the terminal box covers. Remove
terminal box covers and set aside.
3. Remove the power supply knockout from the top or rear of
the vent hood (depending on the incoming location of your
home power supply cable) and install a UL listed or CSA
approved ¹⁄₂" strain relief.
4. Using 2 or more people, lift the hood into final position. Feed
enough electrical wire through the ½" UL listed or CSA
approved strain relief to make connections in the terminal
box. Tighten the strain relief screws.
5. Position the range hood so that the large end of the keyhole
slots are over the mounting screws. Then push the hood
toward the wall so that the screws are in the neck of the slots.
Tighten the mounting screws, making sure the screws are in
the narrow neck of slots.
6. Connect ventwork to hood. Seal joints with vent clamps or
duct tape to make secure and airtight.
7. Check that back draft dampers work properly.
Make Electrical Connection
1. Disconnect power.
2. Use UL listed wire connectors and connect white wires (A)
together.
3. Use UL listed wire connectors and connect black wires (B)
together.
4. Connect green (or bare) ground wire from power supply to
green ground screw in terminal box and securely tighten.
5. Install terminal box cover.
6. Reconnect power.
A. Terminal box covers
B. Screw (3)
A. Power supply knockout
A
B
A
A. White wires
B. Black wires
C. UL listed wire connector
D. Green (or bare) ground wire
E. Home power supply cable or
power cord accessory kit
F. UL listed or CSA approved
½" strain relief
G. Green ground screw
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
A
B
CDE
F
G
WARNING
Fire Hazard
Electrically ground the blower.
Use copper wire.
Connect ground wire to green ground screw in
terminal box.
Failure to do so can result in death, fire, or
electrical shock.

13
Complete Installation
1. Install the 75W (max.) light bulb. See “Replacing the Light
Bulb” in the “Range Hood Care” section.
2. Replace grease filter if removed. See the “Range Hood Care”
section.
3. Check the operation of the range hood fan and light. See
“Range Hood Use” section.
If range hood does not operate, check to see whether a
circuit breaker has tripped or a household fuse has blown.
Disconnect power and check wiring connections.
NOTE: To get the most efficient use from your new range hood,
read the “Range Hood Use” section.
RANGE HOOD USE
The range hood is designed to remove smoke, cooking vapors
and odors from the cooktop area. For best results, start the hood
before cooking and allow it to operate several minutes after the
cooking is complete to clear all smoke and odors from the
kitchen.
The hood controls are located on the front panel of the range
hood.
Range Hood Controls
Operating the light
Turn the light switch to the right 1 position for Low (night light).
Turn the light switch to the right 2 positions for High.
Operating the fan
The fan is variable speed. Rotate the fan switch to the right to
turn the fan to the ON position. Continue to rotate the switch to
the desired fan speed.
To turn the fan OFF, rotate the fan speed switch to the left to the
OFF position.
RANGE HOOD CARE
Cleaning
IMPORTANT: Clean the hood and grease filters frequently
according to the following instructions. Replace grease filter
before operating hood.
Exterior Surfaces:
IMPORTANT: Do not use soap-filled scouring pads, abrasive
cleaners, Cooktop Polishing Creme, steel wool, gritty washcloths
or paper towels.
To avoid damage to the stainless steel, do not use cleaners that
contain chlorine.
Cleaning Method:
■Rub in direction of grain to avoid scratching or damaging the
surface.
■For stainless steel models, Stainless Steel Cleaner and Polish
Part Number 31462A (not included): See “Assistance or
Service” section to order.
■Liquid detergent or all-purpose cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
■Glass cleaner to remove fingerprints.
Metal Grease Filter
For vented installations:
1. Remove screw from the grease filter retainer.
2. Turn the grease filter retainer to release filter.
3. Wash metal filters as needed in dishwasher or hot detergent
solution.
4. Reinstall the filter by placing the back edge in the channel at
rear of hood. Push filter into place, turn the filter retainer to
secure filter to range hood.
5. Replace screw in the grease filter retainer.
For non-vented (recirculating) installations:
The charcoal filter is not washable. It should last up to 6 months
with normal use.
1. Replace metal grease filter with a charcoal filter. For
information on ordering, see the “Accessories” section.
To replace filter:
1. Remove screw from the grease filter retainer.
2. Turn the grease filter retainer to release filter.
3. Reinstall the filter by placing the back edge in the channel at
rear of hood. Push filter into place, turn the filter retainer to
secure filter to range hood.
4. Replace screw in the grease filter retainer.
A. Light housing and cover
B. Grease filter retainer
C. Grease filter
A. Fan speed switch
B. On/Off light switch
A
C
B
AB
A. Filter retainer
A

14
Replacing the Light Bulb
Turn off the range hood and allow the light bulb to cool.
1. Disconnect power.
2. Squeeze the plastic lens cover and remove it from the hood.
3. Screw light bulb into socket.
4. Replace lens cover by squeezing cover and inserting tabs
into slots.
5. Reconnect power.
If new light does not operate, make sure the lamp is inserted
correctly before calling service.
WIRING DIAGRAM
A. Light bulb socket
B. Lens cover
AB
L3
2
1
C25
SE114A
1.2 ±10% A
73 ±10% Watts
17.1 ±10% Ohms
13.6 ±10% Ohms
Motor Characteristics
Power Supply 120 VAC
Frequency 60 Hz
Amperage
Wattage Rating
Motor Resistance
White - Red
White - Black
Lamp Switch
Off - Low - High
Motor Switch
Off - On
Lamp Switch
Operation
1 - 3 Low
1 - 2 Off
1 - L High
Ground
Screw
GND
LN
BK
WH
RD
Speed 2
Common
Speed 1
RD
WH
NOTE: Speed 1
not used
RD
BK
BK
RD
BK
WH
BK
WH
YL
Rectifier
Diode

15
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check to see
whether a circuit breaker has tripped or a household fuse has
blown. It may save you the cost of a service call. If you still need
help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only factory specified parts. Factory specified parts will fit
right and work right because they are made with the same
precision used to build every new IKEA®appliance.
To locate factory specified parts in your area, call us or your
nearest designated service center.
In the U.S.A.
Call the Whirlpool Customer eXperience Center toll free:
1-866-664-2449.
Our consultants provide assistance with:
■Features and specifications on our full line of appliances.
■Installation information.
■Use and maintenance procedures.
■Accessory and repair parts sales.
■Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
■Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
IKEA Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
Call the Whirlpool Canada LP Customer eXperience Centre toll
free: 1-866-664-2449.
Our consultants provide assistance with:
■Features and specifications on our full line of appliances.
■Use and maintenance procedures.
■Accessory and repair parts sales.
■Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool Canada LP designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For further assistance
If you need further assistance, you can write to Whirlpool
Canada LP with any questions or concerns at:
Customer eXperience Centre
Whirlpool Canada LP
200 – 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
Accessories
Stainless Steel Cleaner and Polish
Order Part Number 31462A
Charcoal Filter Kit
Order Part Number W10355450
Power Cord Kit
Order Part Number W10355452
7" (17.8 cm) Round Damper
Order Part Number W10355451
30" (76.2 cm) Extension Panel
Order from IKEA®Part Number 302-822-39

16
IKEA MAJOR APPLIANCE WARRANTY
How long is the IKEA limited warranty valid?
This limited warranty is valid for five years from the date of purchase, when this major appliance is operated and maintained according
to instructions attached to or furnished with the product, unless the appliance is named LAGAN in which case this limited warranty is
valid for one year from the date of purchase. This limited warranty is valid only in the United States or Canada and applies only when the
major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this
limited warranty.
Which appliances are not covered by the IKEA five (5) year limited warranty?
For major appliances named “LAGAN,” this limited warranty is valid for one year from the date of purchase.
Who will execute the service?
This limited warranty is provided by Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”). Service must be provided by
a Whirlpool designated service company.
What does this limited warranty cover?
The limited warranty will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed
when the major appliance was purchased. The exceptions are specified under the headline “What is not covered under this limited
warranty?”.
What will be done to correct the problem?
The designated service company will examine the product and decide, at its sole discretion, if it is covered under this limited warranty.
If considered covered, the designated service company will then repair the defect. Your sole and exclusive remedy under this limited
warranty shall be product repair as provided herein.
What is not covered under this limited warranty?
■Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
■Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
■Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used
in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
■Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved for use.
■Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported within 30 days from the date of purchase.
■Any food loss or medicine loss due to refrigerator or freezer product failures.
■Pick up and delivery. This major appliance is intended to be repaired in your home.
■Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
■Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized servicer is not available.
■The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
■Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot
be easily determined.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
Disclaimer of Implied Warranties
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO FIVE YEARS (ONE YEAR FOR MAJOR APPLIANCES NAMED “LAGAN”) OR THE
SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of
merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have
other rights that vary from state to state or province to province.
Limitation of Remedies; Exclusion of Incidental and Consequential Damages
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
How to reach us if you need our service
If outside the 50 United States and Canada, contact your authorized IKEA retailer to determine if another warranty applies.
If you need service, please read the Installation Instructions and/or the “Troubleshooting” section of the Use & Care Guide before
contacting us. If you need additional help, do not hesitate to contact us in the U.S.A. and Canada at 1-866-664-2449. 2/09

17
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________

18
SEGURIDAD DE LA CAMPANA PARA COCINA
Si no sigue las instrucciones de inmediato, usted puede
morir o sufrir una lesión grave.
Si no sigue las instrucciones, usted puede morir o sufrir
una lesión grave.
Todos los mensajes de seguridad le dirán el peligro potencial, le dirán cómo reducir las posibilidades de sufrir una lesión y lo que
puede suceder si no se siguen las instrucciones.
Su seguridad y la seguridad de los demás es muy importante.
Hemos incluido muchos mensajes importantes de seguridad en este manual y en su electrodoméstico. Lea y obedezca siempre
todos los mensajes de seguridad.
ADVERTENCIA
PELIGRO
Este es el símbolo de advertencia de seguridad.
Este símbolo le llama la atención sobre peligros potenciales que pueden ocasionar la muerte o una lesión a
usted y a los demás.
Todos los mensajes de seguridad irán a continuación del símbolo de advertencia de seguridad y de la palabra
“PELIGRO” o “ADVERTENCIA”. Estas palabras significan:
Advertencias de la Proposición 65 del estado de California:
ADVERTENCIA: Este producto contiene una o más sustancias químicas identificadas por el estado de California como
causantes de cáncer.
ADVERTENCIA: Este producto contiene una o más sustancias químicas identificadas por el estado de California como
causantes de defectos congénitos o algún otro tipo de daños en la función reproductora.

19
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
LEA Y GUARDE ESTAS INSTRUCCIONES
ADVERTENCIA: PARA REDUCIR EL RIESGO DE
INCENDIOS, CHOQUE ELÉCTRICO O LESIONESA
PERSONAS, OBSERVE LO SIGUIENTE:
■ Use estaunidad sólo de lamaneraparalaque fue
diseñadapor el fabricante. Si tiene preguntas, póngase en
contacto con el fabricante.
■ Antesde dar servicio o limpiar estaunidad, apague el
suministro de energíaen el panel de servicio, y bloquee los
mediosde desconexión del servicio paraevitar que se
enciendaaccidentalmente el suministro de energía.
Cuando el medio de desconexión del servicio no se pueda
bloquear, sujete de maneraseguraun dispositivo de
advertenciaprominente, como podríaser unaetiqueta, al
panel de servicio.
■ El trabajo de instalación y cableado se debe llevar acabo
por unapersona(s) calificada(s), en conformidad con todos
loscódigosy estándaresaplicables, incluyendo
construccionesclasificadas como resistentesal fuego.
■ No opere ningún ventilador que tengaun cable o enchufe
dañado. Deshágase del ventilador o devuélvalo aun lugar
de servicio autorizado paraque seaexaminado y/o
reparado.
■ Esnecesario que hayasuficiente aire paralaadecuada
combustión y ventilación de gasesatravésdel conducto (la
chimenea) del equipo que consume combustible, para
evitar que ocurracontratiro. Sigalaguíay losestándares
de seguridad del fabricante del equipo de calefacción,
como serían aquéllospublicadospor National Fire
Protection Association (NFPA) (Asociación nacional de
protección contraincendios), American Society for Heating,
Refrigeration and Air Conditioning Engineers(ASHRAE)
(Sociedad estadounidense paraingenierosde calefacción,
refrigeración y acondicionamiento de aire) y las autoridades
de códigoslocales.
■ Cuando corte o taladre en unapared o techo, no dañe el
cableado eléctrico ni otrosserviciospúblicosocultos.
■ Losventiladorescon conductossiempre deben dar salidaal
aire haciael exterior.
CUIDADO: Parausarse solamente en ventilación
común. No lo utilice paraventilar materialesy vapores
peligrososo explosivos.
CUIDADO: Parareducir el riesgo de incendio y para
ventilar el aire adecuadamente, asegúrese de dirigir el
conducto de ventilación haciael exterior - no ventile el aire
de salidaaespaciosdentro de paredeso techos, áticos,
espaciosangostoso garajes.
ADVERTENCIA: PARA REDUCIR EL RIESGO DE
INCENDIO, SÓLO USE CONDUCTOSMETÁLICOS.
ADVERTENCIA: PARA REDUCIR EL RIESGO DE
INCENDIO PROVOCADO POR GRASA EN LA SUPERFICIE
DE LA ESTUFA:
■ Nuncadeje las unidadesde superficie sin vigilanciacuando
estén en ajustesaltos. Losderramespor hervor causan
salpicaduras grasosas y humeantes, las cualespueden
encenderse. Caliente losaceiteslentamente y con ajustes
bajoso medios.
■ Siempre ENCIENDA lacampanacuando cocine con calor
alto o cuando flamee alimentos(por ejemplo, crepes
Suzette, cerezas Jubileo y flameado de carne de rescon
pimienta).
■ Limpie losventiladorescon frecuencia. No permitaque se
acumule lagrasa en el ventilador o en el filtro.
■ Use cacerolas del tamaño adecuado. Siempre use
utensiliosde cocción que sean losadecuadosparael
tamaño del elemento de lasuperficie.
ADVERTENCIA: PARA REDUCIR EL RIESGO DE
LESIONESA PERSONASSI SE PRENDE FUEGO EN LA
SUPERFICIE DE LA ESTUFA OCASIONADO POR GRASA,
OBSERVE LO SIGUIENTE:a
■ EXTINGA LASLLAMAScon unatapaque encaje muy
bien, unabandejaparagalletas o unabandejametálica, y
luego apague el quemador. TENGA CUIDADO PARA
EVITAR QUEMADURAS. Si las llamas no se extinguen de
inmediato, EVACUE Y LLAME AL DEPARTAMENTO DE
BOMBEROS.
■ NUNCA AGARRE UNA CACEROLA QUE ESTÉ
ARDIENDO - podríaquemarse.
■ NO UTILICE AGUA ni artículosde limpiezacon agua,
incluyendo pañosparavajillao toallas mojadas - podría
ocurrir unaexplosión de vapor violenta.
■ SÓLO use un extinguidor si:
– Sabe acienciaciertaque tiene un extinguidor de clase
ABC y yasabe cómo utilizarlo.
– El incendio espequeño y se encuentracontenido en el
lugar en donde se inició.
– Hallamado al departamento de bomberos.
– Puede apagar el fuego con su espaldamirando hacia
unasalida.
aBasado en “Consejosde seguridad parafuegosde cocina”,
publicado por laNFPA (Asociación nacional de protección
contraincendios).
■ ADVERTENCIA: A fin de reducir el riesgo de incendio
o de choque eléctrico, no use este ventilador con ningún
dispositivo semiconductor parael control de lavelocidad.

20
REQUISITOS DE INSTALACIÓN
Herramientas y piezas
Reúna todas las herramientas y piezas necesarias antes de
comenzar la instalación. Lea y siga las instrucciones provistas
con cualquiera de las herramientas enlistadas aquí.
Herramientas necesarias
■Taladro
■Broca de 1¹⁄₄" (3,0 cm)
■Broca de ¹⁄₈" (3,0 mm) para los orificios piloto
■Lápiz
■Pelacables o cuchillo de uso general
■Cinta de medir o regla
■Pistola para calafateo y masilla para calafateo a prueba de
agua
■Destornillador de hoja plana
■Destornillador Phillips
■Sierra de vaivén o sierra caladora
■Tijeras de hojalatero
■Compás o plantilla de círculo de 8" (20,3 cm)
Piezas suministradas
Saque las piezas del paquete. Verifique que estén todas las
piezas.
■2 tornillos de 3,5 x 9,5 mm
■Compuerta para ducto de escape rectangular de 3¹⁄₄" x 10"
(8,3 x 25,4 cm)
■Placa de montaje para ducto de escape redondo de
7" (17,8 cm)
■Adaptador Torx®† T10
■4 tornillos de montaje de 4,5 x 13 mm
Piezas necesarias
■1 foco de 75 W como máximo y 120 V
■Cubierta para pared o techo con compuerta que coincida
con el sistema de ventilación
■3 conectores para hilos que estén en la lista de UL
■Abrazaderas para ducto/cinta para ducto, según se necesite
Para armarios con profundidad de 15" (38,1 cm) SEKTION de
IKEA
■Panel de extensión de 30" (76,2 cm) (Número de pieza IKEA
302-822-39, consulte la sección “Ayuda o servicio técnico”
para hacer un pedido)
■3 tornillos de montaje y herrajes de montaje (se compran por
separado). Asegúrese de comprar tornillos y herrajes
apropiados para usarse con el tipo de pared.
Para armarios con bases empotradas:
■Dos tiras de relleno de 2" (5,1 cm) de ancho. La longitud y el
espesor están determinados por las dimensiones del hueco.
■Cuatro tornillos de cabeza plana para madera o tornillos para
metales con arandelas y tuercas (para sujetar las tiras de
relleno).
Para las instalaciones con ducto de escape redondo de 7"
(17,8 cm):
■Sistema de ventilación redondo de metal de 7" (17,8 cm)
Para las instalaciones con ducto de escape rectangular de
3¹⁄₄"x 10"(8,3 x 25,4 cm):
■Sistema de ventilación rectangular de metal de 3¹⁄₄" x 10"
(8,3 x 25,4 cm)
Para las instalaciones sin ducto de escape (con
recirculación):
■Juego de filtro de carbón. Para obtener información sobre
cómo hacer un pedido, vea la sección “Accesorios”.
Requisitos de ubicación
IMPORTANTE: Observe todos los códigos y ordenanzas
aplicables.
■Es la responsabilidad del instalador cumplir con los espacios
de instalación especificados en la placa con la clasificación
de modelo/serie. La placa con la clasificación de modelo/
serie está ubicada dentro de la campana para cocina, sobre
la pared izquierda.
■La ubicación de la campana para cocina deberá estar lejos
de zonas con corrientes fuertes de aire, tales como ventanas,
puertas u orificios de calefacción fuertes.
■Deben usarse las dimensiones de la abertura del armario que
se muestran. Las dimensiones proporcionadas proveen los
espacios mínimos. Consulte las instrucciones de instalación
del fabricante de la superficie de cocción/estufa antes de
hacer ningún corte.
■Se requiere un enchufe eléctrico con conexión a tierra. Vea la
sección “Requisitos eléctricos”.
■Se deben sellar todas las aberturas en el techo y la pared en
donde se va a instalar la campana para cocina.
■Estas campanas para cocina se han fijado de fábrica para
instalaciones con ventilación. Los modelos que pueden ser
instalados sin ventilación (con recirculación) necesitan filtros
de carbón. Consulte la sección “Accesorios” para pedir el
juego del filtro de carbón.
Para la instalación en casas rodantes
La instalación de esta campana para cocina debe ajustarse a los
Manufactured Home Construction Safety Standards (Estándares
de seguridad y construcción de casas fabricadas), Título 24 CFR,
Parte 328 (anteriormente conocido como Federal Standard for
Mobile Home Construction and Safety [Estándar federal para la
seguridad y construcción de casas rodantes], Título 24, HUD
Parte 280), o cuando dicho estándar no sea aplicable, el
Manufactured Home Installation (Estándar para instalación en
casas fabricadas) de 1982 (Manufactured Home Sites,
Communities and Setups [Obras, comunidades y proyectos de
casas fabricadas]), ANSI A225.1/NFPA 501A, o la última edición
o con los códigos locales.
†®TORX es una marca registrada de Acument Intellectual Properties, LLC.