iLive IAHB16B User manual

DC IN
AUX IN
MICRO
SD
FEATURES & CONTROLS
WIRELESS HEADPHONES
User’s Guide for Model No. IAHB16 v1312-01
FCC Warnings
Warning: Changes or modications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings and Precautions
• To avoid hearing damage, make sure that the volume on your music player is turned down before
connecting your headphones. After placing headphones in/on your ears, gradually turn up the volume
until you reach a comfortable listening level.
• Lithium batteries, like all rechargeable batteries, are recyclable and should be recycled or disposed
of according to state and local guidelines. They should never be disposed of in normal household
waste, and they should never be incinerated, as they might explode. Contact your local government for
disposal or recycling practices in your area.
• WARNING: This product may contain chemicals known to the State of California to cause birth defects,
or other reproductive harm (California Prop 65). Wash hands after handling.
• This product meets and complies with all Federal regulations.
Power/Pair
Press and hold to turn
the unit On or O.
Press and hold for 4 sec.
to turn the unit on and begin pairing.
SD/BT
Press to switch between SD Card
or Bluetooth modes.
Skip Fwd/Rev/Vol +/−
Press to skip forward
or back an audio track.
Press and hold to set volume level.
Micro SD
Memory Card Slot
AUX In
(3.5mm audio input)
DC Power Input
Power/Pairing
Indicator Light
Play/Pause
Press to play or pause
the current track.
Features
• Supports Bluetooth
• Wireless range: 33 feet
• Built-in microphone
• Aux in (3.5mm audio input)
• Adjustable headband
• On-ear controls
• DC battery power: built-in
rechargeable lithium ion battery
• Battery life: approx. 6 hours
at 50% volume
• Micro-USB port for battery recharge
Includes
• Micro-USB to USB cable

Using the Aux In Audio Input
Requires a 3.5mm audio cable (not included).
1. Connect a 3.5mm audio cable to the AUX IN on the unit and the
audio output on an audio device.
2. Use the controls on the connected device to select and play your audio
through the headphones.
Installing a Micro-SD Memory Card
Requires a Micro-SD card, up to 32GB (not included). Supports MP3 le types.
1. Insert a Micro-SD card into the card slot by pushing it rmly until it seats.
Removal is the opposite of this.
2. Press the SD/BT button to switch to SD mode. Use the controls on the ear
cup to play, pause, or skip tracks on the card.
BLUETOOTH
Pairing a Bluetooth Device for the First Time
1. Simultaneously power on the unit and begin the pairing process by pressing
and holding the Power/Pair button for approximately 4 seconds.
The indicator will ash red and blue. When pairing, remain within 3 feet
of the unit.
2. Using the native controls on your Bluetooth device, select the IAHB16 in
your Bluetooth settings to pair.
If your device requests a password, enter the default password 0 0 0 0 .
Refer to the user’s manual for your specic device for instructions on pairing
and connecting Bluetooth devices.
After initial pairing, the unit will stay paired unless unpaired manually by the
user or erased due to a reset of the device.
3. If your device should become unpaired or you nd it is unable to connect,
repeat the above steps.
AUX IN
MEMORY CARD
LED INDICATORS
Playing Audio Wirelessly
1. To play or pause the selected track, use the controls on the connected
Bluetooth Device or press the Play/Pause button. Use the Skip Fwd/Rev
buttons to skip between tracks.
2. Audio played through the connected Bluetooth device will now be heard
through the headphones.
STATUS INDICATOR
Power On Flashing blue light
Power O No light
Charging Solid red light
Charging Complete No light
Pairing Flashing red and blue lights
To download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit
the support section at: www.iLiveElectronics.com
Para descargar este Manual del Usuario en inglés, español y francés, o para obtener respuestas a preguntas
frecuentes, visite la sección de apoyo en: www.iLiveElectronics.com
Pour télécharger ce guide de l’utilisateur en anglais, espagnol ou français, ou pour obtenir des réponses à des
questions fréquemment posées, consultez la rubrique d’assistance sur: www.iLiveElectronics.com
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com
Customer Service: 1-888-999-4215 | Email Support: [email protected] | Email Parts: par[email protected]
Copyright © 2015 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property
of their respective owners. Specications are subject to change without notice.
INTERNATIONAL SUPPORT
DC IN
AUX IN
MICRO
SD
NICRO SD