iLive IAHN40 User manual

Wireless Headphones
User’s Guide for Model IAHN40 v2567-01
DC IN
DC IN
AUX IN
AUX IN
LED
LED
MIC
MIC
ANC ON / OFF
ANC ON / OFF
Volume/Skip
Press to adjust volume.
Press and hold to skip tracks.
Power/Play / Pause / Speakerphone
Press and hold to power ON or OFF
Press to play or pause audio.
Press to answer incoming phone call.
Active Noise Canceling
Press and hold to turn active noise canceling ON/OFF
Features
• Bluetooth 5.0
• Bluetooth Wireless: range
- 33 ft.
• Built-in microphone
• Aux in (3.5mm audio input)
• Folding adjustable
headband
• On-ear controls
• Voice prompts announce
headphone operations
• Built-in rechargeable
lithium ion battery: life
- approx. 8 hrs at 50%
volume + ANC on
• Micro-USB port for battery
recharge
Includes
• 3.5mm audio cable
• Micro-USB to USB charging
cable
DC Power Input
Microphone
Indicator LED
Aux In
Battery Charging
Initial charge time is approximately 3 hours. Charge fully before
use. The low battery indicator will ash, a voice prompt will
announce “low battery,” then the unit will automatically power
OFF.
1. Using a Micro-USB to USB cable (included), connect to
the USB port of a powered on computer or USB power
adaptor (not included) to charge the unit.
DCIN
DCIN
AUXIN
AUXIN
LED
LED
MIC
MIC
ANCON / OFF
ANCON / OFF
STATUS INDICATOR
Power On Flashing blue light
Charging Solid red light
Charging Complete Light OFF
Pairing Flashing red / blue light
Pairing Complete Flashing blue light

Pairing Bluetooth & Playing Audio
After initial pairing to a Bluetooth device, the headphones will
stay paired unless unpaired manually by the user, or erased due
to a reset of the device. If your device should become unpaired
or you nd it is unable to connect, repeat these steps.
1. Power ON the headphones.. The headphones defaults to
Bluetooth Mode and is ready to pair automatically. When
pairing, remain within 3 feet of the Bluetooth device.
2. Using the controls on your Bluetooth device, select
IAHN40 in the Bluetooth Settings to pair. If need be, refer
to the user’s manual for your specic device for more
information.
3. When successfully paired, a voice will announce,
“Bluetooth is connected.”Your Bluetooth device will now
be heard through the headphones.
4. Use the controls on the connected Bluetooth device
to select and play audio. Use the headphone controls
or the connected Bluetooth device to play, pause, skip
and adjust the volume level. Note: To pair to a dierent
Bluetooth device, turn o Bluetooth on the currently
connected device rst.
Customer Support
Customer Service: 1-888-999-4215 | Email Support: prodinfo@
dpiinc.com | Email Parts: [email protected]
For Warranty Information and the most up-to-date version of
this User’s Guide, go to www.iLiveElectronics.com
To download this User’s Guide in English, Spanish, or French, or
to get answers to frequently asked questions, visit the support
section at: www.iLiveElectronics.com
Para descargar este Manual del Usuario en inglés, español y
francés, o para obtener respuestas a preguntas frecuentes,
visite la sección de apoyo en: www.iLiveElectronics.com
Pour télécharger ce guide de l’utilisateur en anglais, espagnol
ou français, ou pour obtenir des réponses à des questions
fréquemment posées, consultez la rubrique d’assistance sur:
www.iLiveElectronics.com
Copyright © 2020 Digital Products International (DPI, Inc.).
All other trademarks appearing herein are the property of their
respective owners.
Specications are subject to change without notice.
FCC Warnings
WARNING: Changes or modications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings
• WARNING: To prevent re or shock hazards, do not expose this unit to rain
or moisture.
• WARNING : Where the mains plug or appliance coupler is used as the
disconnect device, such disconnect device shall remain readily operable.
• Lithium batteries, like all rechargeable batteries, are recyclable and should be
recycled or disposed of according to state and local guidelines. They should
never be disposed of in normal household waste, and they should never be
incinerated, as they might explode. Contact your local government for disposal
or recycling practices in your area.
• This product meets and complies with all Federal regulations.
• To avoid hearing damage, make sure that the volume on your music player
is turned down before connecting your headphones. After placing headphones
in/on your ears, gradually turn up the volume until you reach a comfortable
listening level.
Aux In
Aux In mode will function even if the headphones are not
powered on. To conserve battery power, keep them powered
o when using Aux In.
Requires a 3.5mm audio cable (included).
1. Connect a 3.5mm audio cable to the Aux In on the
headphones and the audio output on an audio device.
2. Use the controls on the connected device to select and
play audio.
Active Noise Canceling
The Active Noise Canceling feature will electronically mute
background noise. It can be used with the Bluetooth or Aux
In modes to enhance the quality of any music or audio that is
playing through the headphones.
Active Noise Canceling mode will function even if the
headphones are not powered ON.
1. To activate noise cancelling, press and hold the M
button. The Indicator LED will turn green.
2. To deactivate noise cancelling, press and hold the M
button again. The green LED will turn o.
DCIN
DCIN
AUXIN
AUXIN
LED
LED
MIC
MIC
ANCON / OFF
ANCON / OFF
WARNING : This product can expose you to chemicals
including lead, which is known to the State of California to
cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
This product meets and complies with required Federal
product guidelines.
Previously Connected Devices
• The headphones can remember multiple Bluetooth
devices and will always try to re-connect to the last
device used.
• To re-connect to a dierent device, turn o Bluetooth on
unwanted devices, then access the Bluetooth settings
menu on the device you wish to use and select IAHN40.