illy IPERESPRESSO Y3.3 User manual

24
EN IMPORTANT: Never immerse the machine or its removable compo-
nents in water or put it in the dishwasher.
The water in the tank must be replaced regularly. Do not use the appliance without
water in the tank. It is advisable to use a descaler specifically designed for espresso
machines at least once every 2 months following the instructions found in the
chapter on DESCALING. The machine is equipped with a valve allowing to maintain
constant pressure, which may cause some water to drip from the brew group.
TECHNICAL DATA Mod. 641
Body material: ABS
Heat exchanger material: aluminium
Water tank capacity: 0.750 litres
Used capsule tray: 7 capsules
Pump: 19 bar
Weight without packaging: 3.4 Kg
Power: 220-240V, 50-60Hz; 127V - 60Hz (BRA)
Power: 850W with "Power save" function
Dimensions (W x D x H) (mm): 100x298x254
Capitani Piazza IV Novembre 1 - SOLBIATE CON CAGNO (CO)
The manufacturer reserves the right to make changes or improvements without prior
notice.
ONLY USE IPERESPRESSO CAPSULES WITHTHIS MACHINE.
DISCOVER AND BUY ILLY IPERESPRESSO CAPSULES AT SHOP.ILLY.COM,
AT THE SHOPS OR AUTHORISED ILLY CAFÉS OR CALL THE FREEPHONE
NUMBER 800-821021 (ONLY FROM ITALY).
SUMMARY
GENERAL MACHINE OPERATING RULES..................................................... 24
TECHNICAL DATA..................................................................................... 24
MACHINE PARTS ..................................................................................... 25
MACHINE INSTALLATION AND STARTUP .................................................. 26
MAKING AN ESPRESSO............................................................................ 28
SUGGESTIONS......................................................................................... 28
MAKING BREWED COFFEE........................................................................ 29
SUGGESTIONS......................................................................................... 29
PROGRAMMING THE QUANTITIES............................................................. 30
PROGRAMMING THE TEMPERATURE......................................................... 31
CLEANING AND MAINTENANCE ................................................................ 32
SUGGESTIONS......................................................................................... 32
DESCALING............................................................................................. 33
DESCALING  PROBLEM  CAUSE  SOLUTION ............................................. 35
WARRANTY LIMITATIONS........................................................................ 35
DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE .............. 36
WARNINGS  STATUS  MACHINE............................................................... 37
PROBLEM  CAUSE  SOLUTION................................................................. 38
GENERAL MACHINE OPERATING
RULES
Read the instruction manual and the warranty limitations carefully.
Themachinemust beconnected to aproperlygrounded poweroutlet.The machinemust
be kept clean by frequently washing the cup holders, the drip tray, the used capsule tray
and the water tank. Maintenance must be carried out with the machine off.

25
EN
MACHINE PARTS
1 CAPSULE COMPARTMENT OPENING/CLOSING LEVER
2 BREW BUTTONS:
> ESPRESSO COFFEE
> BREWED COFFEE
3 COFFEE DISPENSING SPOUT
4 MUG HOLDER SURFACE
5 REMOVABLE USED CAPSULE TRAY
6 POWER CORD
7 WATERTANK
8 ESPRESSO CUP HOLDER SURFACE
9 IPERESPRESSO CAPSULES:
> FOR ESPRESSO COFFEE
> FOR BREWED COFFEE
10 DATA PLATE(UNDER BASE) 3
8
4
7
1
5
6
9
10
1-2 sec.
ON
2 sec.
OFF
2

26
EN MACHINE INSTALLATION AND STARTUP
When used for the first time, or if the machine has been turned off for a long period of time, wash the tank before filling it. Furthermore it is recommended to dispense at
least 3 mugs of water to rinse the internal machine circuits, proceeding as follows.
1 2 3 4
Remove the tank, pushing it downwards. Turn the tank outwards. Fill the tank with fresh water to the maximum
level.
Attach the tank containing the descaling
solution .
Make sure that the tank is completely engaged.
56
1-2 sec.
78
Connect the machine to the power outlet. Turn on the machine by pressing one of the two
coffee buttons for 1-2 sec.
Makesuretherearenocapsulesinthemachine. The and buttons will start to flash.

27
EN
9
1 min.
10 11
After approx. 1 minute, they will turn on fixed
and the machine is ready to be used.
Place an empty mug below the dispenser. Press the or button and wait until the
water stops dispensing. The machine is rinsed
when at least 3 mugs of water have been dis-
pensed.The machine is now ready for use.
Power Save function
If the machine remains on and it not used, the Power Save function activates after 15
minutes and the and buttons turn off.
To reactivate the machine, press one of the two buttons and wait for them to turn on fixed.
The machine is now ready for use.
If the machine will not be used for a long period of time, turn off the machine, unplug it
from the power outlet and empty the water tank.

28
EN MAKING AN ESPRESSO
123 4
Use the illy capsules shown in the figure. Slowly lift (to the stop) the lever that opens/
closes the capsule compartment.
Insert the capsule as shown in the figure. Close the lever completely.
5 6 7 8
Lower the cup support grid. Fill the tank with
fresh drinking water.
Place an espresso cup below the dispenser. Press and release the button. The machine
will stop dispensing automatically.
To eject the used capsule, slowly lift the lever
and the capsule will be automatically collected
in the specific container. If the capsule is not
ejected, repeat the operation.
SUGGESTIONS
To enjoy a high quality espresso remember to:
• Use the capsule for espresso with the button. If the incorrect capsule/button combination is used, repeat the operation correctly.
• Change the water in the tank every day.
• Use water with a total hardness of less than 12 French degrees to reduce scaling in the machine;
• Use thick and preheated cups to prevent the coffee from cooling down too fast.The cups can be heated by rinsing them with hot water.

29
EN
MAKING BREWED COFFEE
123 4
Use the illy capsules shown in the figure. Slowly lift (to the stop) the lever that opens/
closes the capsule compartment.
Insert the capsule as shown in the figure. Close the lever completely.
5 6 7 8
Move the cup support grid to the vertical
position.Fillthetankwithfreshdrinking water.
Place a large cup or mug below the dispenser. Press and release the button. The machine
will stop dispensing automatically.
To eject the used capsule, slowly lift the lever
and the capsule will be automatically collected
in the specific container. If the capsule is not
ejected, repeat the operation.
SUGGESTIONS
To enjoy a high quality espresso remember to:
• Use the capsule for espresso with the button. If the incorrect capsule/button combination is used, repeat the operation correctly.
• Change the water in the tank every day.
• use water with a total hardness of less than 12 French degrees to reduce scaling in the machine;
• Use thick and preheated cups to prevent the coffee from cooling down too fast.The cups can be heated by rinsing them with hot water.

30
EN PROGRAMMING THE QUANTITIES
1234
Put a capsule in the provided space. Close the lever completely. Programming espresso:
Use the capsule shown in the figure. Press and
hold the button, the machine will start to
dispense coffee. Release the button once the
desired quantity is reached.
Programming brewed coffee:
Use the capsule shown in the figure.
Press and hold the button. The machine
will start delivering coffee. Release the button
once the desired quantity is reached.
Factory settings
Button Capsule Quantity Cup
Espresso:
medium roast,
dark roast,
decaf
approx. 25 ml
Long espresso
(blue capsule)
approx. 50 ml
Brewed coffee approx. 220 ml
The machine is now programmed.The next time the or button is
pressed, the machine will dispense the quantity of coffee that was just stored.
HOW TO COME RETURN THE MACHINETO THE FACTORY SETTINGS:
With the lever open, turn on the machine by pressing one of the two coffee buttons for
1-2 sec.
Press the button 5 times within 15 seconds.
The and buttons will flash quickly for 2 seconds and will then turn on fixed.
Now the machine has returned to the factory settings for both preparations, both for the
quantity as well as the temperature.

31
EN
PROGRAMMING THE TEMPERATURE
1
1-2 sec.
2
x 5
34
With the lever open, turn on the machine by
pressing one of the two coffee buttons for 1-2
sec.
Do not insert a capsule.
Press the button 5 times within 15 seconds
of turning on the machine. Both buttons will
flash. It is now possible to change the tempera-
ture as described in points 3 and 4.
Press the button to increase the tempera-
ture.The button flashes. Both buttons flash
after approx. 3 seconds.
Press the button to decrease the tempera-
ture.The button flashes. Both buttons flash
after approx. 3 seconds.
The machine is now programmed.The next time the or button is
pressed, the coffee is dispensed at the temperature that was just stored.
HOW TO COME RETURN THE MACHINETO THE FACTORY SETTINGS:
With the lever open, turn on the machine by pressing one of the two coffee buttons for
1-2 sec.
Press the button 5 times within 15 seconds.
The and buttons will flash quickly for 2 seconds and will then turn on fixed.
Now the machine has returned to the factory settings for both preparations, both for the
quantity as well as the temperature.

32
EN CLEANING AND MAINTENANCE
1
2 sec.
234
Switch off the machine by pressing the two
coffee keys simultaneously for 2
seconds.
Remove the capsule holder. The capsule holder
can contain a maximum of 7 capsules. There-
fore it should be emptied regularly to prevent
the capsules from getting stuck.
Empty the capsule holder and rinse it.
Clean the tray and grid of residual water and
coffee. Once clean, engage the tray in the grid.
Rinse the components under running water
and dry them. Do not wash the components in
the dishwasher.
SUGGESTIONS
• If the machine is not being used, turn it off and unplug it from the power outlet.
• Store the capsule coffee machine in a dry place, away from dust and out of the reach of children.
• It is recommended to put the machine in its original packaging.
• The storage temperature must not be lower than 5°C, to avoid the internal machine parts from
being damaged due to the water freezing.
• To ensure correct hygiene and maintain high product quality, it is advisable to expel the capsule
immediately after the coffee is dispensed.

33
EN
DESCALING
If the dispensing buttons and flash alternately, the machine must be descaled. Read all instructions carefully before performing the descaling in order to
familiarise yourself with the process.The cycle lasts about 8 minutes.
N.B.: If the operations are not carried out according to the indicated time, the machine will not start the descaling process. In this case, turn off the machine and repeat
the steps from the beginning.
Limescale accumulation is a normal result of machine use. The machine has an automatic program that helps optimise cleaning and removes scale deposits from the interior. If
the descaling procedure is not carried out, scale may cause malfunctions that are not covered by the warranty.
Use only descaling products for coffee machines. Do not use vinegar, lye, salt or formic acid as they damage the machine. Follow the procedure described below and not the
instructions on the package of the descaling solution.
1
2 sec.
234
Close the lever, do not insert any capsule.
Switch off the machine by pressing the two
coffee keys simultaneously for 2
seconds.
Remove the tank and empty the remaining
water.
Fill the tank with fresh water to the maximum
level and let the descaling solution dissolve.
Attach the tank containing the descaling
solution .
Place a container of at least 0.75 litre capacity
under the dispensing spout.

34
EN 5
5 sec.
678
Turn on the machine by pressing the button
for 5 seconds.
After 5 seconds the button will start
flashing. Release the button .
The button flashes.
Press the button to start the descaling cycle.
The machine begins dispensing water.
At the end of the descaling cycle, the button
is steady on while the button is flashing.
Remove the container and empty it.
Wash the tank thoroughly and fill it with fresh
water.
Attach the tank containing fresh water (see
point 3).
Place a container of at least 0.75 litre capacity
under the dispensing spout.
Pressthe button tostart the rinse cycle.The
machine begins dispensing water.
910
Atthe end of the rinse cycle,thebutton and
the button flash simultaneously.
Remove the container and empty it.
Wait until the button and the button
become steady on.
The machine is now ready for use.

35
EN
DESCALING - PROBLEM - CAUSE - SOLUTION
PROBLEM CAUSE SOLUTION
The descaling/rinsing cycle is interrupted.
Power failure. When the power is restored, the cycle resumes automatically after the interruption.
The machine has been accidentally turned off. Turn the machine on again: the cycle resumes automatically after the interruption.
Opening the lever when the cycle has already
started. Close the lever: the cycle resumes automatically after the interruption.
The machine does not brew water. The water tank is empty. Fill the water tank.
WARRANTY LIMITATIONS
CAUTION:
If descaling is not carried out regularly, limescale may cause malfunctions that are not covered by the warranty. Do not use vinegar, lye, salt or
formic acid as they may damage the machine. Use only descaling products suitable for coffee machines. The descaling solution must be disposed
of according to applicable regulations. Do not drink the liquid dispensed during the descaling process; the machine may not be used for brewing
coffee until after the descaling process has terminated.
The warranty does not cover failures caused by:
• A lack of periodical descaling.
• Operation at a voltage other than what is specified on the data plate.
• Misuse or failure to follow instructions.
• Changes made internally.
• The warranty does not cover repair costs for machines that have been tampered with by unauthorised service centres. Such costs will be entirely payable by the customer.
• Do not to wash the drip tray and the used capsule tray in the dishwasher machine. Failure to follow these instructions may cause problems to both components that are
not covered by the warranty.
CAUTION:
Saving the original packaging (at least over the warranty period) is advisable in the event that the machine needs to be sent to an authorised
service centre. Any damage caused due to transport without proper packaging is not covered by the warranty.

36
EN DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE
Disposal of used electric and electronic appliances, by private persons in the European Union.
TheWEEE symbol used on this product means that it must notbe disposed of togetherwith other domestic waste but must be collected separately. Consumers have the option
of handing in used appliances to distributors, free-of-charge on a 1:1 basis, when they purchase a new product.
For further information about the collection of appliances to be scrapped, please contact the local authority in your town of residence, the local waste disposal service or the
retailer where the product was purchased. Consumers are responsible for disposing of appliances in accordance with applicable law, and non-compliance may be subject
to penalties.
The correct disposal of this product will contribute to protecting the environment, natural resources and human health.

37
EN
WARNINGS - STATUS - MACHINE
Both buttons flash
The machine has been turned on and is heating up.
On fixed
The machine has reached the correct temperature for dispensing.
The espresso button is on fixed
The machine is dispensing an espresso.
The brewed coffee button is on fixed
The machine is dispensing a brewed coffee.
The buttons flash alternating
The machine must be descaled.
Slow flashing (only the brewed coffee button)
The machine indicates that the descaling procedure has been selected. In this condition, the tank contains the descaling solution.
Fast flashing (only the brewed coffee button)
The machine indicates that the first part of descaling is in progress. The machine is dispensing the descaling solution.
Slow flashing (only the brewed coffee button) and the espresso button on fixed
The machine indicates that the first part of descaling is completed. Rinse the tank and refill it with fresh drinking water.
Fast flashing (only the brewed coffee button) and the espresso button on fixed
The machine indicates that the second part of descaling is in progress. The machine is dispensing water for rinsing the circuit.
Fast flashing (only the espresso button)
The machine is malfunctioning. Turn off and then on again after 30 seconds. If the defect occurs again, contact an authorised service centre.

38
EN
Problem Resolution If the problem persists
The machines does not turn on. Check the socket, the plug, the voltage and that you have pressed one of the two coffee buttons for 1-2
seconds.
Contact an authorised help
centre.
The machine does not brew coffee.
The water tank is empty. Fill the water tank.
Tank not inserted correctly. - Insert the water tank correctly.
Incomplete closure of the moving part of the machine head. - Close the lever tight.
Pump won't start. - Dispense water without capsule and then try again with new capsule.
The machine makes too much noise. The water tank is empty. Fill the water tank.
Tank not inserted correctly. - Insert the water tank correctly.
Droplets of water leak from the unit after it is
turned on. It is not a problem, the machine is warming up.
The machine brews coffee slowly.
The speed of brewing depends on the variety of coffee.
You're using a different type of capsule. - Check the type of capsule used.
There is limescale. - Run the descaling cycle.
The machine brews coffee too fast. The speed of brewing depends on the variety of coffee.
You're using a different type of capsule. - Check the type of capsule used.
The coffee is cold. Warm up the cup.
Coffee tastes sour. Brew a couple of cups of water.
Capsule expired. - Use a new capsule.
The buttons flash alternately. Descaling cycle required. - Run the descaling cycle.
The "espresso" button flashes quickly. The machine is malfunctioning.Turn off and then on again after 30 seconds.
The descaling cycle does not start. Descaling must be done with the machine cold.
PROBLEM - CAUSE - SOLUTION