imilab EC3 Pro User manual

IMILAB EC3 Pro Outdoor Security Camera
User Manual
Read this manual carefully before use, and retain it for future reference.

CONTENTS
English 01-15
16-30Deutsche
31-45Español
46-60Italiano
61-75Français
76-90Pусский

Product Introduction
Wall base
(can be rotated
to adjust the
camera angle)
SpeakerKnob
Reset button
Micro SD card slot
In this instruction manual, images of the device, accessories and user interface are for
illustrative purposes only and should only be used for reference.
The actual device may differ from the illustrations due to product updates and upgrades.
Please refer to the actual device.
EN-01

Power supply
Indicator
light
Antenna
Mic
Packing list: IMILAB EC3 Pro Outdoor Security Camera, wall mounting pack, power
adapter, user manual
EN-02

Installing the Device
Then secure the camera to the metal rod with a screw.
Note: The warranty does not cover any damage caused by improper installation. Please
follow the instructions.
EN-03
1. Attach the positioning sticker on the desired installation location. Drill four holes at the
positions indicated on the sticker. Drilling diameter of around 6.0mm; drilling depth of
around 30mm.
Mounting the device
Note: Please check that the Wi-Fi signal is strong enough before mounting the device.

2. Insert four plastic expansion nuts into
the holes.
3. Cover part of power cable with the
base plate as indicated.
4. Put the base plate on the wall.
Ensure that the power cable goes
straight down. Secure the base
plate by inserting the screws into
the expansion nuts.
EN-04

Note:
In order to prevent accidents and injuries, please secure the device firmly onto the
wall as illustrated. The wall on which the device is mounted must have a loading
capacity of at least 3 times the weight of the device.
Do not install the device near a heat source, such as an air-conditioner compressor,
air vent of a range hood or air vent of a gas water heater.
As the camera can be rotated horizontally, please pay attention to the safe turning
distance during installation. Do not install the device at a location where its
horizontal movement would be impeded.
The distance between the base plate and the wall should be at least 50mm to allow for
a safety turning distance. Any gap of less than 50mm will result in an obstruction to the
camera's movement.
Top view
50mm < 50mm
EN-05

Note:
When inserting or removing the micro SD card, please disconnect the camera from the
power supply. Please use a micro SD card from a reputable manufacturer. The
recommended read and write speed of the micro SD card is at least U1/Class 10.
Connecting the Device
Turn on the camera
Step 1: Insert the power supply cable into the camera's power supply port. Connect
the other end of the power supply cable to a power source.
Step 2: When connected to a power supply, the indicator light will show the camera's
status. When the indicator light is yellow, the camera is being turned on; when the
indicator light is flashing yellow, it is waiting to beconnected.
Insert a micro SD card
Ensure that the camera is disconnected from the power supply. Use a screwdriver to
remove the protective case and expose the micro SD card slot. The contact points of
the micro SD card should be facing the same direction as the camera. Insert the micro
SD card into the slot.
MicroSD
EN-06

Restoring factory settings
Press and hold the reset button to restore the factory settings. The content inside the
micro SD card will not be deleted.
Specifications
Manufacturer: Shanghai Imilab Technology Co., Ltd.
Address: Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District,
Shanghai, China
For further information, please go to www.imilab.com.
Support: [email protected]
www.imilabhelp.com
EN-07
Name: IMILAB EC3 Pro Outdoor Security Camera
Model: CMSXJ42A
Input: 12V 1A
Resolution: 2304×1296
Operating Temperature: -20℃~ 40℃
Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4GHz
FCC ID: 2APA9-CMSXJ42A
Item Dimensions: 158*91*117mm
Net Weight:435g
Viewing Angle: 110°
Aperture: F2.1

Connecting to Mi Home App
This product works with Mi Home and can be controlled using the Mi Home app.
Scan the QR code to download and install the Mi Home app. If you already have Mi
Home app installed, you will be directed to the device connection page. You can also
search for "Mi Home" in an app store to download and install the Mi Home app.
About Works with Mi Home
A product that works with Mi Home can be controlled using the Mi Home app. Please
note that such products are only verified at the software level. Xiaomi and Mi Home
are not responsible for the production, implementation of
standards and quality control of these products and their
manufacturers.
Note:
The actual operation may differ from the instructions above due to Mi Home app
upgrades and updates. Please follow the instructions shown by the Mi Home app.
EN-08

2021 3 2 20:51:05
Infrared Night Vision
The light sensor can automatically switch the device to night vision mode through
IR-CUT based on changes in the lighting of the environment.The device features 2
built-in infrared night vision lights that ensure recording stays clear even in darkness.
Infrared night vision effect illustration
EN-09

Video Playback
Past videos can only be viewed when a compatible micro SD card is inserted in IMILAB
EC3 Pro Outdoor Security Camera. After inserting a micro SD card and turning on the
device, the camera will automatically start recording.
In the control interface of the Mi Home app, tap the playback button to enter the
video playback page. You can also view a recording by selected a time period.
IMILAB EC3 Pro Outdoor ...
12MB / s
06:20
EN-10

Sharing a Video
In the control interface for IMILAB EC3 Pro Outdoor Security Camera in the Mi Home
app, you can set the device as a shared device in the settings menu and invite others
to watch the recordings. Users must download the Mi Home app and login to their
Xiaomi account in order to view the recordings of the shared device.
EN-11
Share group
Check for firmware updates
Rename IMILAB EC3 Pro ...
Security settings
Share device
Remove device
Add Home screen shortcut
Feedback
Network info
Share with Mi Account
Share manage
Share...General settings

Home Security
The Home Security function can be turned on/off in the control interface for IMILAB
EC3 Pro Outdoor Security Camera in the Mi Home app.
The device can detect and record movements within the viewing angle and push
the recording to the client. Users can set the surveillance time, alert sensitivity, alert
interval, etc.
EN-12

The working temperature of the device is -20℃ to 40℃. Do not use the device when
the temperature is too high or too low.
For better results, avoid placing the camera in front of or next or a glass surface, a
white-colored wall or other reflective surfaces as this may cause the recording to
have un-even lighting between the foreground and background or be over-exposed.
Please ensure that the device is within Wi-Fi signal coverage. Place it at a location
with good Wi-Fi signal strength. Try to avoid placing the device near a metallicobject,
a microwave oven or other objects that may cause signal interference.
Precautions
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment. This device
complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
FCC Statement
EN-13

equipment generates, uses, and canradiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC 20cm Statement: This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20cm between the radiator & your body. This transmi er must not be
co-located or operating in conjunction with any other antenna or transmier.
EN-14

WEEE Disposal and Recycling Information
For pluggable equipment, the socket-outlet (power adaptor) shall be installed near the
equipment and shall be easily accessible.
Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio equipment type
IMILAB EC3 Pro Outdoor Security Camera is in compliance with Directive 2014/53/EU.
Adaptor Statements
Correct Disposal of this product. This marking indicates that product should not
be disposal with other household wastes through out the EU. To prevent possible
harm to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse sustainable reuse of
material resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take this
product for environment safe recycling.
EN-15

Manufacturer: Shanghai Imilab Technology Co., Ltd.
Address: Room 001A, Floor 11, Block 1, No. 588 Zixing
Road, Minhang District, Shanghai, China
For further information, please go to www.imilab.com.
Support: [email protected]
www.imilabhelp.com