impact CAS Series User manual

Required Tools:
1. 3/8" Combination Wrench
2. 1/8" Allen Wrench
Assembly Instructions for the Impact Dog Crates
Customer Assembled Stationary Dog Crate
Helpful Hints:
oTypical assembly time: 1-2 hours
oYour crate is designed to last and the parts are made for a solid fit. Because of this some
parts may need help aligning. To help screw holes align try placing a screw onto the allen
wrench, and threading the screw into the crate while pushing the parts into alignment.
oWhen installing parts, start all screws for that part first before fully tightening. This will help
ensure the easiest installation for all screws.
Read these instructions carefully before
beginning to assemble your crate, this will
familiarize you with the process and help the
assembly go more smoothly.
Acorn Nuts
(65 Supplied)
Screws
(75 Supplied)
3/8" Combination Wrench
(1 Supplied)
1/8" Allen Wrench
(1 Supplied)

CAS Series Assembly Instructions
- Set Top Panel on it's side
-> (Either side - the Top Panel is symmetric)
1
- Set Front Panel inside of Top Panel
-> Place Front Panel so the hinge is on the left
- Install screws (4) with nuts inside crate
-> Loosely secure all (4) screws, tighten with
screws once all are in place
2
- Move to opposite side
- Place Rear Panel in Top Panel, vent holes
toward top
- Install screws (4) with nuts inside crate
-> Loosely secure all (4) screws, tighten with
screws once all are in place
3
Page 2

CAS Series Assembly Instructions
- Set male corners on crate, secure
- Install screws (3) with nuts inside crate
-> Loosely secure all (3) screws, tighten with
screws once all are in place
4
- Move to bottom of crate, place side panel on side
of crate (Either direction, the part is symmetric)
-> Slide Side Panel under the Top Panel's flange
to align screw holes
- Secure Side Panel to Front & Back Panels with (6)
screws and nuts.
-> Loosely tighten all screws, tighten with tools
once all in place.
5
- Set Airline Rail on side of crate.
- From inside of crate, start all (6) screws into rail,
then tighten all screws.
6
Page 3

CAS Series Assembly Instructions
- Turn over crate to access the other side, use
packing materials to cushion your crate on the
floor, if desired.
- Repeat Step 4 to install second (2) male corners.
7
- Move to bottom of crate.
- Repeat Step 5 to install second side.
8
- Set Airline Rail on side of crate.
- Repeat Step 6 to install second Rail.
9
Page 4

CAS Series Assembly Instructions
- Turn crate onto it's top.
- Set (2) Female Corners on crate Back Panel.
- Install (2) screws & nuts per corner into
Back Panel and Side Panel
(bottom hole will not be used).
-> Loosely tighten nuts, tighten with tools
once in place.
10
- Set Bottom Pan in place, with tray on inside.
- Follow number sequence to install
1. Slide Bottom under Curners installed in Step 10.
2. Pinch Bottom to back at Loction 2 pictured.
3. Lower Bottom onto interal rail on Front Panel.
- Place a screw through the Back Pan into Bottom
Panel, hand tighten nut onto screw.
- Place remaining screws & nuts into Bottom Pan.
- Tighten all screws & nuts with tools once in place.
11
- Move to front of crate, open the door.
- Repeat Step 10 to install the last female corners
onto the front of the crate.
12
Page 5

CAS Series Assembly Instructions
- Turn your crate over so the handles are on top.
CONGRATULATIONS!
You have finished assembling your
Impact Dog Crate!
Page 6