Impex SB 681 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
SB 681
Retain This
Manual for
Reference
03-22-05
OWNER'S
MANUAL
APEX MULTI PURPOSE
FID BENCH
SB 681
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE PACK……….....…....................................................................... 3
ASSEMBLY INSTRUCTIONS........................................................................... 4
EXPLODED DIAGRAM.........................................................................………. 8
PARTS LIST…………………………………………………………………………. 9
WARRANTY.................................................................................................… 10
ORDERING PARTS......................................................................................... 10
BEFORE YOU BEGIN
Thank you for selecting the APEX Multi Purpose Bench SB681 by IMPEX
INC. For your safety and benefit, read this manual carefully before using the
machine. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are missing
or damaged parts, we guarantee you complete satisfaction through direct
assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

HARDWARE PACK
3

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended this machine be assembled by two or
more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Main Frame (#1) to the Front Stabilizer (#2). Secure it with two M10 x 2 ¾”
Carriage Bolts (#21), one Bracket (#15), two ∅¾” Washers (#27), and two M10 Aircraft
Nuts (#28).
B.) Attach the Main Frame (#1) to the Rear Stabilizer (#3). Secure it with two M10 x 2 ¾”
Carriage Bolts (#21), one Bracket (#15), two ∅¾” Washers (#27), and two M10 Aircraft
Nuts (#28).
DIAGRAM 1
4

STEP 2 (See Diagram 2)
A.) Slide the Sliding Block (#5) onto the Incline Adjustment Bar (#4).
B.) Attach both ends of Incline Adjustment Bar to the open brackets on the Main Frame
(#1). Secure each end with one M10 x 2 ½” Carriage Bolt (#22), Ø ¾” Washer (#27),
and M10 Aircraft Nut (#28).
C.)Use a Lock Knob (#16) to lock the desired incline position.
DIAGRAM 2
5

STEP 3 (See Diagram 3)
A.) Attach the lower holes on the Backrest Supports (#7) to the pivot on the Sliding Block
(#5). Secure them with one M12 x 5 ¾” Allen Bolt (#19), two ∅1” Washers (#25), and
one M12 Aircraft Nut (#26).
B.) Attach the Seat Support Frame (#6) to the hole on the Backrest Support (#7). Make
sure the Seat Support Frame is on the outside of the Backrest Support. Align the holes
and secure them with one M12 x 2 ½” Allen Bolt (#20), two Ø 1” Washers (#25), and
one M12 Aircraft Nut (#26). Repeat the same step to install the other side. Note: The
Bolt must be inserted from inside of Backrest Support to the outside of the Seat
Support Frame.
C.)Loosen up the Knob Bolt on the Sliding Track to adjust the position so the front end of
the two Seat Support Frames (#6) can be aligned to the pivot on the Main Base Frame
(#1). Secure them with one M12 x 7 5/8” Allen Bolt (#18), two Ø 1” Washers (#25), and
one M12 Aircraft Nut (#26). DIAGRAM 3
6

STEP 4 (See Diagram 4)
A.) Insert the Foam Tube (#10) halfway through the hole on the Main Frame (#1).
Push two Foam Rolls (#12) onto the Foam Tube from both ends. Plug the Foam
Roll End Caps (#11) into the ends.
B.) Place the Seat (#8) onto the Seat Support Frames (#6). Secure it with four M8 x 2”
Allen Bolts (#23) and ∅5/8” Washers (#24).
C.)Place the Backrest Board (#9) onto the Backrest Supports (#7). Secure it with four
M8 x 2” Allen Bolts (#23) and ∅5/8” Washers (#24). DIAGRAM 4
7

EXPLODED DIAGRAM
8

PARTS LIST
KEY NO. DESCRIPTION Q’ty
1 Main Frame 1
2 Front Stabilizer 1
3 Rear Stabilizer 1
4 Incline Adjustment Bar 1
5 Sliding Block 1
6 Seat Support Frame 2
7 Backrest Support 2
8 Seat 1
9 Backrest Board 1
10 Foam Tube 1
11 Foam Roll End Cap 2
12 Foam Roll 2
13 Sliding Block Sleeve 2
14 2 ¾” x 2” End Cap 4
15 Bracket 2
16 Lock Knob 1
17 1 5/8” x ¾” End Cap 12
18 M12 x 7 5/8” Allen Bolt 1
19 M12 x 5 ¾” Allen Bolt 1
20 M12 x 2 ½” Allen Bolt 2
21 M10 x 2 ¾” Carriage Bolt 4
22 M10 x 2 ½” Carriage Bolt 2
23 M8 x 2” Allen Bolt 8
24 ∅5/8” Washer 8
25 Ø 1” Washer 8
26 M12 Aircraft Nut 4
27 Ø ¾” Washer 6
28 M10 Aircraft Nut 6
#8 Allen Wrench (Tool) 1
#5 Allen Wrench (Tool) 1
9