Incra Miter1000SE User manual
Manufactured by Taylor Design Group, Inc. P.O. BOX 810262 Dallas, TX 75381 ©2008 by Taylor Design Group, Inc. All rights reserved.
°When using the INCRA Miter1000SE in conjunction with any other tool, first read and follow all instructions and safety
information in that tool’s owner’s manual.
° Never let the saw blade come in contact with the aluminum or steel components of the INCRA Miter1000SE.
° When using the INCRA Miter1000SE, always keep your hands clear of the saw blade and the line of cut.
° Always turn offthe power and make sure that the saw blade comes to a complete stop before changing the setting of any part of
the INCRA Miter1000SE.
° Always securely tighten the large black clamping knob before starting any cut.
° Wear safety glasses, hearing protection, and follow all normal shop safety practices.
° After making any adjustments to the miter angle or fence position of your INCRA Miter1000SE, always verify safe clearance
between the blade and fence before turning on the saw.
° After making any adjustments to the fence position on the INCRA Miter1000SE, always make sure that the two socket head
screws are securely tightened.
° When using the INCRA Flip Shop Stop to position a piece for a cut, always hold or otherwise clamp the board between the stop
and the blade.
OWNER’SMANUAL
www.incra.com
Important safety instructions for using the INCRA Miter1000SE
SAFETY:
Before using the INCRA
Miter1000SE, read and
follow all of the instructions
and safety information in
this owner’s manual.
INCRA MITER1000SE OWNER’S MANUAL
Manufactured by Taylor Design Group, Inc. P.O. BOX 810262 Dallas, TX 75381 WWW.INCRA.COM
Page 2
Assembly and Calibration
1. Attach Clamping Knob and T-Clip
Remove the hex bolt that secures the protractor head
and replace with the large threaded knob included in
the hardware pack. The washer on the hex bolt must
be used with the threaded knob, Fig. 1. If the Miter
slot in your table saw has a T-slot, attach the T-clip to
the end of the miter bar as shown in Fig. 2.
2. Adjust the Miter Bar
Loosen the (2) fasteners that secure the fence to the
fence-mounting bracket and remove the fence. Adjust
the miter bar at each of the (3) expansion mechanism
locations in the miter bar for a good fit in your table
saw’s miter slot. Turning the screw clockwise expands
the mechanism. You’ll find (2) of the expansion loca-
tions in front of the protractor. Adjust these (2) front
expansion points first, expanding a little at each of the
locations until the bar slides smoothly, Fig. 3.
Remove the large clamping knob with washer and
pivot the protractor head to gain access to the rear
expansion point, Fig. 4. After adjustment, replace the
washer and large clamping knob.
3. Attach the Fence
Place your Miter1000SE in the preferred miter slot
at your table saw. (Note: Left hand miter slot use
shown. See step 4 to convert fence for use in right
hand miter slot.) Attach the fence to the fence mounting
bracket and slide the fence to a position that leaves
safe clearance between the end of the fence and the
blade. Tighten the (2) 1/4-20 fasteners, Fig. 5.
Fig. 1 Attach Clamping Knob
Fig. 2 Attach T-Clip
Fig. 3 Expand Miter Bar to Fit (front)
Fig. 4 Expand Miter Bar to Fit (rear)
Fig. 5 Attach Fence
Large knob
Washer
Remove hex bolt
Miter bar
#10-24x1/4”
Phillipsathead
screw
T-clip (use only in T-slot
miter channels)
Fenceremovedfor
access
Adjust(2)frontexpansionpoints
1/420socketheadscrews
Positionforsafe
clearancebetweenfence
andblade
Adjustrear
expansion point
Remove knob
androtate
protractorfor
access.
Replaceafter
adjusting
rear expansion point.
INCRA MITER1000SE OWNER’S MANUAL
©2008 by Taylor Design Group, Inc. All rights reserved. Rev.07.08.08
Page 3
4. Left or Right of Blade
Your new Miter1000SE fence is factory configured for
use to the left of the blade. If you prefer to use your
Miter1000SE in the right hand miter slot just follow
the steps below.
Loosen the 1/4-20 socket head screw located at the
end of the 14” section of the fence, then slide out the
4” section of fence along with the attached extender
bar. Move the socket head screw, washer and rectan-
gular nut to the hole on the opposite end of the fence.
Slide the extender bar assembly into the end of fence,
capturing the rectangular nut in the T-slot on the
extender bar. The higher numbers on the extender
bar scale should be closest to the saw blade. Loosen
the (2) socket head fasteners that secure the 4”
section of fence and reverse it. Tighten all fasteners,
Fig 6. Slide the scale in the top of the fence out
and replace with the included reverse reading (0-14”)
scale.
5. Adjust Fence Mounting Bracket 90°
to Saw Blade
Set the protractor head to read 0°, engaging the tooth
on the actuator firmly into the 0° notch on the protractor
head, Fig. 7. Tighten the large clamping knob then tighten
the actuator thumbscrew.
Using the supplied 5/32” hex key, loosen the (3) socket
head screws that secure the fence-mounting bracket
to the protractor head. Unplug your table saw, then
use a reliable machinist square to set the fence at 90° to
the saw blade, Fig. 8. Tighten the (3) socket head screws.
e method used to join the fence-mounting bracket to the protractor head makes it easy to fine-tune the fence
perfectly perpendicular to your tabletop. To adjust, loosen the (3) socket head screws that secure the bracket and
slide a paper shim between the bracket and the protractor head. Placing the shim behind the screws will decrease
the angle. Placing the shim in front of the screws will increase the angle.
TIP
This one time calibration prepares your INCR A
Miter1000SE for work in either miter slot. Just remember that the accuracy of the INCRA Miter1000SE at
any subsequent setting is dependent upon the accuracy of your initial 90° calibration. Verify this important
calibration with a test cut and fine tune as necessary.
SQUARING THE FENCE TO YOUR TABLE SAW TOP
Fig. 6 Converting Fence for use on Right Side of Blade
Fig. 7 Set Protractor to 0°
Fig. 8 Square Fence to Blade
Movefastenersto
oppositeendoffence
4”fencesection
Extenderbar
Remove
extenderbar
assembly
Tighten large
clamping knob, then
tighten actuator
thumbscrew
Actuator tooth
engagedat0°
Loosensocketheadscrewsandadjust
fenceusingreliablemachinistsquare
INCRA MITER1000SE OWNER’S MANUAL
Manufactured by Taylor Design Group, Inc. P.O. BOX 810262 Dallas, TX 75381 WWW.INCRA.COM
Page 4
Operation – Changing Angle Settings
Before using your new INCRA Miter1000SE for
the first time, take a few moments to review these
important operational procedures.
1. 5° Indexing (including 221/2° and 671/2°
settings)
Loosen the actuator thumbscrew and pivot the
actuator tooth away from the notches located on the
perimeter of the protractor head. Loosen the large
clamping knob and rotate the protractor head and
fence to the desired angle, Fig. 9. Then firmly engage
the tooth on the actuator with the corresponding
notch on the protractor head. The actuator tooth
should point directly to the desired angle on the scale.
Tighten the large clamping knob, then tighten the
actuator thumbscrew, Fig. 10.
2 . Cont in uo us Adj us tm en ts (fo r a ngle
settings finer than 5° increments)
Pivot the actuator tooth away from the notches on
the protractor head, aligning the arm over the miter
bar, and tighten the thumbscrew. Now loosen the
small nylon thumbscrew on the actuator and pivot the
1/10° vernier cursor toward the scale. Rotate the cur-
sor until it is aligned edge to edge with the scale and
tighten the thumbscrew. When you change miter
angles, just align the desired angle on the scale with
the “0” cursor line, Fig. 11. For 1/10° adjustments,
use the alignments as described in the 1/10° vernier
instructions on page 8.
CAUTION:
AFTER MAKING ANY ADJUSTMENTS TO TH E
MITER ANGLE OF YOUR INCRA MITER1000SE,
ALWAYS VERIFY SAFE CLEARANCE BETWEEN
THE FENCE AND THE BLADE BEFORE TURNING
ON THE SAW.
Fig. 10 Locking the Protractor
Miter1000SE
Fig. 9 Changing Angles
Fig. 11 Continuous Adjustments
Loosen large
clamping knob
andactuator
thumbscrew
Pivot the actuator tooth
awayfromprotractor
Tighten large clamping
knob then tighten
actuator thumbscrew
Rotate protractor
Firmly engage
actuator tooth with
protractor
Pivot cursor
to scale
Pivotactuatortoothawayfrom
protractorandtightenthumbscrew
INCRA MITER1000SE OWNER’S MANUAL
©2008 by Taylor Design Group, Inc. All rights reserved. Rev.07.08.08
Page 5
Flip Fence and Flip Shop Stop - Calibration and Operation
As you look at your new INCRA Flip Shop Stop and
Flip Fence for the first time you will see an interesting
detail. The front face of the fence uses a tongue and
groove arrangement to accept a mating feature on the
flip arms, Fig. 12. When the flip arm is down with
the two opposing features engaged, it becomes
impossible for the sharp corner of a mitered board
end to wedge between the fence and flip arm. Com-
bined with INCRA’s famous incremental positioning
capabilities, you’ll soon be duplicating cut off lengths
with machine shop precision.
Zeroing the Fence Scales
To zero the main fence scale for 90° work, first set
the protractor to the 0° setting and lock in place.
Clamp the Flip Shop Stop to the fence so that the 0”
mark on the fence scale reads directly under the end
of the gold component of the Flip Shop Stop, Fig. 13.
Now loosen the (2) 1/4-20 socket head screws that
secure the fence to the fence mounting bracket and
slide the fence toward the blade until the Flip Arm on
the stop contacts the blade. Re-tighten the fasteners,
Fig. 13A.
For stopped cuts beyond the range of the main fence you’ll need to
calibrate the extender bar scale. Clamp the INCRA Flip Shop Stop to
the 4” fence extender. (Use the scale on the short section of fence as
a reference for clamping the stop to the same position each time you
use it.) Now loosen the 1/4-20 socket head screw located at the end of
the longer fence and slide the 4” fence and extender bar out. Use
a tape measure to set the distance between the blade and the flip arm
at 16” and re-tighten the fastener, Fig. 14. Now simply slide the scale
in the extender bar to read 16” at the end of the longer main fence
section, Fig. 14A.
Fig. 12 Flip Shop Stop
Fig. 13 Zeroing Fence Scale
Fig. 13A Slide Fence to Blade
Fig. 14A Align Scale
Fig. 14 Setting Extender Bar Scale
Tongueandgroove
Clamp Flip Shop Stop at
0” position
Slidefenceuntilip
armcontactsblade,
thentightenfasteners
Slidescaletoread
16”atendofmainfence
Loosenfastener Clamp
stop to
4”fence
section
Slideextenderbarout
untiliparmis16”from
bladethentightenfastener
Protractor
setat0°
INCRA MITER1000SE OWNER’S MANUAL
Manufactured by Taylor Design Group, Inc. P.O. BOX 810262 Dallas, TX 75381 WWW.INCRA.COM
Page 6
For mitered cutting, a test cut is often the most ac-
curate means of setting the fence and extender bar
scales since measuring to the tooth of a blade set at
an angle to the fence can be difficult. Begin by setting
the desired miter angle and check for safe clearance
between the fence and blade. Clamp the stop to the
fence about 10” away from the blade. Miter a piece of
scrap stock with this setup. Measure the length of the
cut piece, Fig. 14B. Then simply slide the scale on
the fence to read the length of the cut directly under
one end of the stop.
Micro Adjusting
To micro adjust your Flip Shop Stop’s position, begin
by loosening the (2) socket head screws located on
the top of the stop body. Now turn the micro adjust
socket head screw to fine tune the stop position,
Fig. 15. When unscrewing the micro adjust screw,
apply pressure to the stop body to keep it against the
screw end. After adjustment, always tighten the (2)
socket head screws on top of the stop body.
Flip Arms and Stop Rods
The dual flip arms and stop rods provide a variety of
stop configurations. The flip arms can be used without
the stop rods when you want to take advantage of the
fence/arm tongue and groove feature for stop control
on mitered board ends. Typically, you will use the
longer rod to join the two arms together, Fig. 16. This
produces an arrangement that, when pivoted, moves
both arms simultaneously. The rod can be positioned
so that it is the actual stop surface or it can be posi-
tioned slightly behind the front of the arm so that the
aluminum arm is the actual stop surface.
By placing one of the shorter 1-1/2” rods in each of the
two stop arms, you can use the two stop arms in-
dependently, Fig. 17. For example, you can calibrate
one for work to the left of the blade and the other
for work to the right. On one side of the blade you
might want to position the stop rods to provide two
different cut off lengths from one stop position. By
using varying combinations of long or short rods you
can create as much as 7-3/4” between the two stop
positions.
Fig. 14B Setting Scales for Angled Cuts
Fig. 15 Micro Adjusting
Fig. 16 Long Stop Rod
Fig. 17 Short Stop Rods
Slidescaletoread
cut length here
Measure length
ofcut
Loosen (2) socket
headscrews
Turnthissocketheadscrew
toadjust
Longstoprodusedto
joiniparms
Short stop
rodsallow
independent
iparm
use
INCRA MITER1000SE OWNER’S MANUAL
©2008 by Taylor Design Group, Inc. All rights reserved. Rev.07.08.08
Page 7
Making a Zero Clearance Wooden Sub
Fence
A sub fence can be used to provide tear out control
as well as support for your workpiece up to and be-
yond the blade. A good material to use for making
your zero clearance sub fence is 3/4” medium density
fiberboard (MDF). Use the drill and counter bore di-
mensions shown in Fig. 18. Attach using the supplied
fasteners. Adjust the length of the fence to accom-
modate your application. Note: In applications where
the incremental stopping capability of the Flip Shop
Stop is required, the wooden sub fence can be no
taller than 2-1/2”.
Expanded Flip Stop Clamping Mode
The two-part body design of the INCRA Flip Shop
Stop allows for use with up to a 3/4” thick wooden sub
fence. To expand the INCRA Flip Shop Stop, loosen
the (2) socket head screws located on the top of the
stop body, then slide the upper portion of the stop
off. Now slide the upper portion back on, capturing
the rectangular nuts in the second T-slot located on
the lower portion (gold component) of the stop body,
Fig.19.
To avoid the saw blade pulling your workpiece into the cut, add a strip of adhesive backed sandpaper to the front
face of the wooden sub fence.
TIP
WARRANTY
TAYLOR DESIGN GROUP, INC. WARRANTS THIS PRODUCT FOR ONE YEAR FROM DATE OF PURCHASE. WE
WILL REPAIR ANY DEFECTS DUE TO FAULTY MATERIAL OR WORKMANSHIP, OR AT OUR OPTION, REPLACE
THE PRODUCT FREE OF CHARGE. PLEASE RETURN THE FAILING COMPONENT ONLY, POSTAGE PREPAID,
ALONG WITH ADESCRIPTION OF THE PROBLEM TO THE ADDRESS BELOW. THIS WARRANTY DOES NOT
APPLY TO PARTS WHICH HAVE BEEN SUBJECTED TO IMPROPER USE, ALTERATION, OR ABUSE.
LIFETIME WARRANTY ON POSITIONING RACKS
IF AN INCRA POSITIONING RACK IN THIS TOOL BECOMES DAMAGED FOR ANY REASON, TAYLOR DESIGN
GROUP WILL REPLACE IT FREE OF CHARGE FOR AS LONG AS YOU OWN YOUR TOOL. RETURN THE DAM-
AGED RACK, POSTAGE PREPAID, PLEASE ALLOW 1 TO 2 WEEKS FOR DELIVERY.
Fig. 18 Making a Sub Fence
Fig. 19 Expanded Flip Stop Clamping Mode
21/2” max (see note)
5/16” through hole w/
3/4”dia.x3/8”deep
counter bore
1/4-20
rectangular nut
1/4”atwasher
1/4-20 x 3/4”
socketheadscrew
11/16”
3/4”
Goldcomponent
Loosensockethead
screwsandslidered
assembly into 2nd T-slot
ongoldcomponent
Subfence
©2008 by Taylor Design Group, Inc. All rights reserved. Rev.07.08.08
Page 8
Manufactured by Taylor Design Group, Inc. P.O. BOX 810262 Dallas, TX 75381 WWW.INCRA.COM
MADE IN THE
USA
Manufactured by:
Taylor Design Group, Inc.
P.O. BOX 810 262 Dal las, T X 753 81
www.incra.com
INCRA Tools are protected by one or more of the following US patents:
#4,793,604, #4,930,221, #5,195,730, #5,275,074, #5,423,360, #5,716,045, #6,237,457,
#6,557,601, #6,672,190. Other patents granted or pending.
INCRA is a Registered Trademark of Taylor Design Group, Inc.
©2008 Taylor Design Group, Inc.
Using Your New 1/10° Vernier Cursor
Your new Miter1000SE features several enhancements not included with the standard
Miter1000. Among these is the new 1/10° vernier cursor.
For readings in 1° increments using the cursor, just align any of the protractor scale
marks with the “0” mark on the cursor. For 1/10° adjustments, you will notice 5 marks
on either side of the “0” mark on the cursor. As you gently rotate the protractor you will
readthescaleasfollows:At1/10°rotation,therstmarkaligns1°awayfromtheoriginal
starting point. At 2/10° rotation, the second mark aligns 2° away. At 3/10° rotation, the
third mark aligns 3° away, etc. For 6/10° through 9/10° of rotation, watch for alignments
using the marks on the opposite side of the “0” cursor mark.
Sound complicated? It’s not! Just study the examples on this page.
INCRA MITER1000SE OWNER’S MANUAL
Table of contents
Other Incra Tools manuals
