Inder P-208 User manual

Page # 3 - M:208
WORKING INSTRUCTION
Step 6 : Press right lever (#2) toward left for achieving any angle
from 0 to 180°. If specified angle is required then stop bending while
bending point reaches at angle as shown in fig.3. i.e 90°
Step 7 : Copper Tube Bender is suitable for copper
tube bending having thin wall thickness upto
180° as shown in fig.4
LOCK (#4)
LEFT LEVER (#3)
COPPER TUBE
DIE (#1)
BENDING POINT
RIGHT LEVER (#2)
LEFT LEVER (#3)
LOCK (#4)
COPPER TUBE
RIGHT LEVER (#2)
WARNING
1. Don't use bender more than its capacity.
2. If tube is over size, the die will damage
the tube.
3. Don't use heavy thickness tube bending.
Fig. 4
User’s Instruction Manual
Model : P-208
Note : Before using this COPPER TUBE BENDER carefully read through
this INSTRUCTIONS MANUAL to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available as an
important reference when using this COPPER TUBE BENDER.
COPPER TUBE BENDER
u
Alumini m Head
Steel Head

WARRANTY CERTIFICATE
Product : COPPER TUBE BENDER
Identification : Type Designation : P-208
LIMITED ONE YEAR WARRANTY AGAINST MANUFACTURING DEFECT.
Makes every effort to assure that its Copper Tube Bender meet high
quality and durability standards and warrants to the original purchaser that the product is
free from defects in material and workmanship for the period of one year form the date of
purchase. This warranty does not apply to damage due directly or indirectly to misuse,
abuse, negligence or accidental repairs or alteration outside our facilities, or to lack or
indignance. We shall in no event be liable for death, injuries to person or property or for
incidental contingent, special or consequential damages arising from the use of our
product. Some states don't allow the exclusion or limitation of incidental or consequential
dames, so the above limitation of exclusion may not apply to you.
To take advantages of this warranty, the product or part must be returned to us with
transportation charges pre-paid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection very the defect, we will
either repair or replace the product all elecrole or we may elect to refund the purchase price
if we cannot readily and quickly provide you with replacement. We well return repaired
products all our expense, but if we determine there is no defect, or that the defect resulted
from caused no within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal right and you may also have other rights which vary
from state to state.
12576
49
o
N*
Accredited
by the RvA
SINCE 1958
POWER
Page # 1 - M:208
Features : For long radius thin wall thickness bending 6 to 25 mm Copper, Aluminium, Stainless steel & any
light gauge tube upto 180°.
Page # 2 - M:208
Prod. No. 208A 208B 208C 208D 208E 208F 208G 208H
Size (Inch.) O.D. ¼ 5/16 3/8 ½ 5/8 ¾ 7/8 1
Size (mm) O.D. 6 8 10 12 16 20 22 25
Radius (mm) 15 25 40 60 85 85 95 95
WORKING INSTRUCTION
Step 1 : Take complete Set of Copper Tube Bender.
Step 2 : Check the size of which marked on the die ( #1).
Step 3 : O.D. of tube should be same as the die size.
Step 4 : Take Copper Tube according to die size.
Step 5 : Move right lever and insert copper tube into
die (#1) as shown in fig.2
RIGHT LEVER (#2)
DIE (#1)
LEFT LEVER (#3)
COPPER TUBE
LOCK (#4)
LEFT LEVER (#3)
RIGHT LEVER (#2)
DIE (#1)