Infineon PSoC 62S2 User manual

www.cypress.com/CY8CEVAL-062S2
Quick start guide
PSoC™ 62S2 evaluation kit
CY8CEVAL-062S2
Kit contents
1. PSoC™ 62S2 evaluation board
2. Sterling-LWB5+ Wi-Fi / Bluetooth® M.2 radio module from Laird Connectivity
(plugged into the PSoC™ 62S2 evaluation board)
3. USB Type-A to Micro-B cable
4. FlexPIFA antenna from Laird Connectivity
5. Four jumper wires (four inches each)
6. Two jumper wires (five inches each)
7. Quick start guide (this document)

Quick start guide
USB cable connected to the KitProg3
USB connector
PIFA antenna connected to Sterling-LWB5+
M.2 radio module
Note: The Sterling-LWB5+ M.2 radio module from
Laird Connectivity requires an external antenna for
wireless connectivity. The FlexPIFA antenna is not
connected to the module by default. Follow the
instructions in the "Kit operation" chapter of the
kit guide to connect the antenna to the module.
Before you start
1. Ensure that you have the following:
• PC with USB port
• UART terminal soware such as Tera Term
or Minicom
2. Visit the kit website to download and install the
required soware.
3. Ensure that jumper J18 is at position 3-5 to select
3.3 V.
4. Connect the KitProg3 USB connector (J9)
to your PC.
5. Wait for the driver installation to complete.
Connect the kit with the UART terminal soware
1. Open the UART terminal soware and connect
to the kit’s USB-UART COM port with the
following settings:
• Baud rate: 115200, Data: 8 bit, Parity: None,
Stop bit: 1 bit, Flow control: None
2. Press the XRES switch (SW1) to reset the device.
Run the pre-programmed code example
1. Observe the “Hello World!!!” message on the serial
terminal and confirm that the user LED blinks
at 1 Hz.
2. Press the Enter key to pause or resume blinking
the user LED.
Next Steps
Visit the kit website for information on
code examples supported for this kit and
kit documentation.
USB-UART COM port setup

Quick start guide
PSoC™ 62S2 evaluation board details
1 KitProg3 USB connector (J9)
2 KitProg3 status LED (D4)
3 KitProg3 (PSoC™ 5LP) programmer and
debugger (CY8C5868LTI-LP039, U2)
4 PSoC™ 6 MCU (CY8C624ABZI-S2D44, U1)
5 QSPI F-RAM (CY15B104QSN, U4)
6 KitProg3 programming mode selection button (SW3)
7 OPTIGA™ Trust M security controller (SLS32AIA, U5)
8 512-Mbit serial NOR flash memory (S25FL512S, U3)
9 PSoC™ 6 MCU USB device connector (J14)
10 Headers compatible with mikroBUS by Mikroelektronika
(J19, J23)
11 PSoC™ 6 MCU user buttons (SW2, SW4)
12 System power (VTARG) selection jumper (J18)
13 Potentiometer (R57)
14 Potentiometer connection jumper (J21)
15 PSoC™ 6 MCU reset button (SW1)
16 PSoC™ 6 MCU VDDIO0 current measurement jumper (J20)*
17 PSoC™ 6 MCU 10-pin SWD/JTAG program and
debug header (J24)
18 PSoC™ 6 MCU debug and trace header (J22)*
19 Power LED (D6)
20 CAPSENSE™ slider (CSS1) and buttons (CSB1, CSB2)
21 PSoC™ 6 MCU VDDIO2 current measurement jumper (J17)
22 PSoC™ 6 MCU VDDIO2 power selection jumper (J16)
23 PSoC™ 6 MCU VTARG current measurement jumper (J15)
24 Power header compatible with Arduino Uno R3 (J1)
25 I/O headers compatible with Arduino Uno R3 (J2, J3, J4)
26 M.2 interface connector (J13)
27 Sterling-LWB5+ M.2 module from Laird Connectivity
28 Custom M.2 interface selection jumper (J12)
29 VBAT current measurement jumper (J11)
30 VBAT power selection jumper (J10)
31 PSoC™ 6 MCU user LEDs (D1, D2)
32 RGB LED (D3)
33 GPIO header (J5) for AIROC™ Wi-Fi & Bluetooth®
combo chips*
34 PSoC™ 6 MCU I/O headers (J6, J7)*
35 External power supply VIN connector (J8)
36 microSD card holder (J27)**
* Footprint only, not populated on the board
** Component is located at the bottom side of the board
1
35 34 25
2
3
4
5
6
7
8
9
10
11 11 13 14 15 36 17 20
21
22
23
24
25
26
27
28
29
30
31
32
33
18 19 1612

Quick start guide
See the kit guide available at www.cypress.com/CY8CEVAL-062S2 for details.
PSoC™ 62S2 evaluation board pinout details
I/Os compatible with Arduino Uno R3 PSoC™ 6 MCU I/Os
Note: *Not connected
Interface compatible with mikroBUS by Mikroelektronika
LEGEND
AN/P10_7
RST/P7_5
CS/P1_3
SCK/P1_2
MISO/P1_1
MOSI/P1_0
3.3V
GND
P6_0/SCL
P6_1/SDA
VREF/AREF
GND/GND
P12_2/D13
P12_1/D12
P12_0/D11
P12_3/D10
P7_6/D9
P0_5/D8
3.3V
GND
BT_I2S_CLK
BT_I2S_WS
BT_I2S_DO
BT_I2S_DI
BT_GPIO_2
BT_GPIO_3
BT_GPIO_4
BT_GPIO_5
BT_GPIO_6
M2_SCL
M2_SDA
5V
VCC_VDDIO2
BT_UART_RXD
BT_UART_TXD
BT_UART_CTS
BT_UART_RTS
WL_UART_RX
WL_UART_TX
GPIO11/WL_UART_RTS
WL_REG_ON_ALT
BT_GPIO_7
GND
GND
P5_7/D7
P5_6/D6
P5_5/D5
P5_4/D4
P5_3/D3
P5_2/D2
P5_1/D1
P5_0/D0
P0_3
P0_2
P8_7*
P8_6*
P8_5*
P8_4*
P8_3*
P8_2*
P8_1*
P8_0
P1_5*
P1_4
P0_4
P0_5
P7_4
P7_3
P7_0
P11_1
P13_6
P13_7*
NC
VTRAG/IOREF
XRES/RESET
V3.3/V3.3
V5.0/V5.0
GND/GND
GND/GND
VIN/VIN
P10_0/A0
P10_1/A1
P10_2/A2
P10_3/A3
P10_4/A4
P10_5/A5
P10_6/A6*
P10_7/A7*
P9_0/A8
P9_1/A9
P9_2/A10
P9_3/A11
P9_4/A12
P9_5/A13
P9_6/A14*
P9_7/A15*
PWM/P6_3
INT/P6_2
RX/P13_4
TX/P13_5
SCL/P6_0
SDA/P6_1
5V
GND
Date: 07/2021 All rights reserved. ©2021 Infineon Technologies AG
Document number: 002-33159 Rev. *C