Infineon TriBoard TC3X9 User manual

User Manual Please read the Important Notice and Warnings at the end of this document V1.2
www.infineon.com TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard TC3X9
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
About this document
Scope and purpose
The User Manual provide information about using, configuration and connecting the TriBoard with Infineon
AURIX™ TC3X9 device. The manual provide information for different hardware types. There exist different
hardware with Through Hole socket (TriBoard TC3X9 TH) and soldered devices (TriBoard TC3X9). The schematic
is identically for the all boards if not other mentioned in chapter schematic. The placing on the boards is slightly
different around the TC3X9 itself dependent of the space (socket need more space and has through hole), but the
most components are on the same location. All figures are valid for each board if not differently mentioned.
Intended audience
Design, verfication, test and software engineers will use this document to get an understanding of the
functionality and connections of the TriBoard.

User Manual TOC-2 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
Table of Contents
About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-1
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TOC-2
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.3 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
3 TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.1 Failsafe handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.4 Memory (not with TC3X7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.4.1 Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.4.2 SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.5 USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.5.1 Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.5.2 miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.6 FlexRay™ (E-RAY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.7 Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.8 MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.9 LIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.10 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.11 HSCT (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.11.1 High speed with HSCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.12 Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.13 Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.14 Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.15 Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.15.1 OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.15.2 DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.15.3 DAPE (only Emulation Device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.15.4 High speed with DAP/DAPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.15.5 AGBT (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.15.6 ETK connector (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.15.7 EmW Power (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
4 TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 HW Boot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1.1 Default Pad State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1.2 Bootmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2.1 General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2.2 Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.2.3 Resistors for memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
5 Signal (on board used) Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Table of Contents

User Manual TOC-3 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
Table of Contents
5.2 Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.3 Config Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.4 Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.5 Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.6 Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.7 EBU Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
6 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1 On Board only used signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 TC3X9 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.3 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
6.4 USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
6.5 FlexRay™ (ERAY) connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
6.6 CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
6.7 LIN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.8 HSCT connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.9 Ethernet connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.10 OCDS1 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6.11 DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6.12 ETK connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6.13 Ethernet miniWiggler power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6.14 AGBT connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
7 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1 Known problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1.1 Known problems (TriBoard TC3X9 TH V1.0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1.2 Known problems (TriBoard TC3X9 TH V1.01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1.3 Known problems (TriBoard TC3X9 V1.0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.2 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.3 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
7.4 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

User Manual 1-1 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
Introduction
1 Introduction
We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a versatile tool, providing quick
access to the capabilities of TriCore's powerful architecture.
Applications can be developed easily. The Evaluation Board is equipped with a variety of memories and
peripherals for connection to the environment. There is also an interface for the On Chip Debugging Features
(OCDS1 and DAP).
The Evaluation Board allows easily the development of TriCore applications with the corresponding tools.
Subsequently, the applications can be downloaded and can be tested with the powerful debugger software.
This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you through the
initial configuration of the TriBoard.
For detailed technical information about the TC3X9 (e.g. TC399) please refer to the User Manual of the used
device.

User Manual 2-1 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
Features
2 Features
2.1 Summary of Features
– Infineon’s TC3X9 (TC399) AURIX™ 2G Controller in LFBGA-516 Package
– Infineon’s TC3X7 (TC397) AURIX™ 2G Controller in LFBGA-292 Package
– Burst Flash up to 4MBytes (not with TC3X7)
– asynchronous SRAM up to 2MByte (not with TC3X7)
– synchronous SRAM up to 4MByte (not with TC3X7)
–FlexRay™
1) Transceivers
– High Speed CAN Transceivers (CAN-FD capable)
– USB to UART bridge
– Ethernet Gigabit PHY
–SerialEeprom
–LINTransceiver
– Crystal 20MHz (default) or External Clock
– USB miniWiggler JDS for easy debugging
– 8 Low Power Status LEDs
– 8-DIP switches for configuration
– access to all pins of controller
– 100mm x 160mm (EURO-Board)
Connectors
The TC3X9 TriBoard offers a wide variety of connectors:
– Standard power connector
– Micro USB connector for ASC Interface (ASC0) and miniWiggler
– RJ45 connector for Ethernet
– 16-pin header for JTAG interface (OCDS)
– 2 x 10-pin header for DAP and DAPE (DAPE only usable on Emulation Device)
– 10pin (2x5) Header for LIN Transceiver (LIN)
– 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1)
– 2 x 10pin (2x5) Header for FlexRay™ (ERAY-A and ERAY-B)
– five 80-pin connectors (male) + five 80-pin connectors (female) with all I/O signals
– optional ETK connector
– optional 6pin (IEEE1394) Socket for HSCT
– optional Aurora connector (only with Emulation Device)
Components
– Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV
– Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,25 Volt)
– LED indicating safe state signal 2 from TLF35584
– LED indicating /HDRST (ESR0) active state
– LED indicating activ miniWiggler JDS
– LED switched via DAS software
– 2 x Infineon’s FlexRay™ Transceiver TLE9221SX
– 2 x Infineon’s High Speed CAN-Transceiver TLE9251VSJ
1) FlexRay™ is a trademark of FlexRay Consortium.

User Manual 2-2 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
Features
– Infineon’s LIN-Transceiver TLE 7259-3GE
– USB to UART bridge FT2232HL (FTDI)
– Single Port Gigabit Ethernet PHY PEF7071 (LANTIQ)
– 8 general purpose LEDs
–2KI2C Serial Eeprom with EUI-48™ 1) Node Identity (MICROCHIP)
– Reset switch
–Enableswitch
– Generic switch
– 4-pin Dip switch
Zero Ohm Bridges
Zero Ohm resistors give the flexibility to configure the systems functionality.
1) EUI-48™ is trademarked by IEEE

User Manual 2-3 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
Features
2.2 Block Diagram
Figure 2-1 TriBoard Block Schematic
Micro
USB miniWiggler
OCDS1
USB
XTAL
FlexRay™
Transceiver
Transceiver
TxCAN0
TxCAN1
RxCAN0
RxCAN1
TC3X9
(e.g.
TC399)
TriCore
CPU
PLL
CAN0
CAN1
ERAY B ERAY A
TX0
RX0
8 LED’s
(P33.4 up to P33.7,
P20.11 up to P20.14) Serial EEPROM
with EUI-48™
RMII PHY Twisted Pair RJ45
LIN
LIN
Transceiver
TX1
RX1
HSCT
optional
HSCT - TX/RX
/CS0 or /CS1
/CS0 or /CS1
BUS
ADDRESS and DATA BUS
BUS
BUS SRAM
32 Bit
Burst
FLASH
32 Bit
I²C
WAKEUP
QSPI2
Multi Voltage Safety Micro
Processor Supply
TLF35584QV
ENA

User Manual 2-4 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
Features
2.3 Placement
Note: On soldered board the DAP connector (X402) and the crystal (Y201) are located closer to the TC3X9
(U201) as shown in Figure 2-2 other components are on the same location (see also Figure 7-12).
Figure 2-2 TriBoard TC3X9 (TH) V1.0(1) Placement
ENA
SS2
1
TriBoard-TC3X9 (TH) V1.0(1)
CAN1
P33.7
P33.6
P20.12
P22.11
P20.14
P20.13
+3V3
RST
V_UC+1V25
BOOTCFG
P33.4
P33.5
USB
ERAY-A
ERAY-B
POWER
ETK
1
1
1
1
1
1
RUN
1
1
ETH
LIN
ACT
CAN0
OCDS1
HSCT
111
1
1
P33.11
/PORST
X501
S502
U502
D508
U501
L502
L501
C502
C501
R501
X502
1
X702
1
X705
U604
U603
1
X701
1
X704
X404
S501
X401
D504 D507
D506
D505
D309D308D307D306D305D304D303D302
1
X703
X302 X301
T302
T301
Y201
X402
Y401
U401
BU401
D401
C303
U307
X303X304X305
F
X306
X201
Y301
4
3
2
1
S201
X403
S202
U201
D402
DAPE
DAP
EmW_pwr

User Manual 3-1 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
3 TriBoard Information
3.1 Power Supply
All needed voltages are generated via Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV and via
the microcontroller itself (+1,25V).
The supply device is available as two different devices:
TLF35584QVVS1 -> +5V standby voltage, +5V TriCore supply (V_UC)
TLF35584QVVS2 -> +3,3V standby voltage, +3,3V TriCore supply (V_UC)
Dependent of the assembled device the board works with 5V or 3,3V IO.
The TLF35584QV provide the following voltages:
+3,3V or +5V for standby (connected to VEVRSB)
+3,3V or +5V for TriCore (connected to VEXT)
+5V communcation supply (used by CAN and FlexRay™ transceivers)
+5V voltage reference (connected to VDDM and VAREFx)
+3,3V via LDO directly from pre regulator (used by Ethernet PHY and on board memories)
Applying a stable supply voltage causes the power on reset after a short period. The three LED's (V_UC, +3.3V,
+1V25) indicate the status of the on board generated voltages.
A manual power on reset is executed by pressing the reset button.
The Board has to be connected to a +3,5V to +40V DC power supply.
The power consumption is not specified yet but a supply with 12V and 500mA is recommended. The pinout for
the supply connector is shown in Figure 6-4. There can be used any standard power pack with a connector where
the positive line is surrounded by the ground line.
3.1.1 Failsafe handling
In case that the device don’t contains a program which disable or service the window watchdog and error pin
monitor of the TLF35584 then the TLF35584 is going to a FAILSAFE state where all supplies are switched off. This
state can be left via reconnect the power plug or via the ENA button (S502). In this case you must connect a
debugger which is able to disable the window watchdog and error pin monitor to reprogram the microcontroller.
In the default state of the board the switching to FAILSAFE state is switched off via resistor R508. Beginning with
schematic V1.02 R509 is assembled with 20K and R508 with 0R. If only R508 or R509 assembled then the board is
manufactured with earlier Version (V1.01). In this case you should remove R509 (if assembled) or change R509 to
20K and assemble R508 with 0R to avoid the FAILSAFE state and switching off the supplies.
If you will use/evaluate all safety features of the TLF35584 make sure that R509 is assembled and R508 is not
assembled. Make sure that you have a proper initialization of TLF35584 in your softare.
Resistor R508 and R509 are red marked in the following Figure 3-1:

User Manual 3-2 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
Figure 3-1 Resistors for TLF35584 Safety feature handling with switch on
3.2 LEDs
There are 15 LEDs on board:
– D302 up to D305 (blue) -> toogle LEDs connected to P33.4 ... P33.7
– D306 up to D309 (blue) -> toogle LEDs connected to P20.11 ... P20.14
– D504 RST (red) -> RESET LED indicate the reset state of the board (/ESR0)
– D505 +1V25 (green) -> +1V25 power supply indication
– D506 +3V3 (green) -> +3,3V power supply indication
– D507 V_UC (green) -> +5V/+3,3V power supply indication
– D508 SS2 (green) -> safe state signal 2 indication
– D402 ACT (green) -> on board miniWiggler JDS is ACTIV
– D401 RUN (blue) -> Debug RUN mode (switched by DAS Server)
3.3 Clock
On the board is a fixed crystal with 20MHz assembled. You can change this by replacing Y101 (soldered).
3.4 Memory (not with TC3X7)
The TriBoard supports the following memory configurations:
• up to 4 MBytes external Burst Flash (1x32Bit) or
• up to 2 MBytes external asynchronous SRAM (2x16Bit) or
• up to 4 MBytes external synchronous SRAM (1x32Bit) or
• up to 1 MBytes external asynchronous SRAM (1x16Bit)
X501
S502
U502
C505
D508
U501
L502
L501
CB501
C502
C507
C509
C508
C501
C503
C504
R501
R507
R508
R509
CB502
X502
1
X702
R611
R610
R609
R620
R618
R619
R602
Q601
1
X705
U604
U603
R604
R606
R608
R607 R605
R603
CB620
CB619
CB618
CB617CB616
CB615 CB614
CB613
CB612
CB611
CB610
CB609
CB608
CB607
1
X701
R398
1
X704
X404
R452
R354
S501
X401
D504 D507
D506
D505
D309 D308 D307 D306 D305 D304 D303 D302
1
X703
X302 X301
T302 T301
R356
R355
R336
R335
R531
R439
C302 C301
R532
R397R396
R395
R394
R393R392
R391
R399
R324
R357 R337
Y201
R207
R206
C202
C201
R202
R201
R428
R427
R426
R425
R424
R344
X402
CB402
R402
R403
CB408
Y401
U401
U404
CB401
R401
D402
L401
BU401
R411
C402
CB405
R423
R429
R430
D401
CB414
CB415
CB416
CB417
CB418
CB419
R444
R446
R454
R456
R455
R451
U406
U407
U408
C303
C305
C307
C308
D301
L301
R359
R361
R382
R384
R385
R374
R378
R230
R232
R234
R236
U307
X303X304X305
F
X306
X201
Y301
R377
4
3
2
1
S201
R375
R376
R601
R390
R329
R453
X403
R203
R204
R205
R217
R255
R256
S202
R225
R226
U201

User Manual 3-3 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
For the On Board Memory are reserved chip select 0 and 1. Therefore only two parts, e.g. 1x32Bit Flash and
2x16Bit asynchronous SRAM, should be assembled and can be used at the same time. Chip Select 2 is used as
Burst Address Advance output on the board and can be used externally only if the flash and the sysnchronous
SRAM (if assembled) are not used in burst mode.
3.4.1 Flash
The flash uses 32 Data Bits (AD0...AD31) and 20 Address Bits (A0...A19). It’s accessed via /CS0 or /CS1. The flash
has its own resistor to connect to /CS0 or /CS1. To connect the flash see Table 4-4.
Note: Only +3,3V Flash is usable with this board.
3.4.2 SRAM
The SRAM uses 32 Data Bits (AD0...AD31) and up to 20 Address Bits (A0...A19).
It’s accessed via /CS0 or /CS1. Each type of SRAM has its own resistor to connect to /CS0 or /CS1. To connect
different SRAMs see Table 4-4.
Note: Only +3,3V SRAM is usable with this board.
3.5 USB Connector
The USB connector is used for connection to a PC. Via the USB it is possible to power the board, using the ASCLIN0
as serial connection via USB and Debugging via DAS. For the pinout of USB socket see Figure 6-5.
NOTE: Before connecting the board to the PC, make sure that the actual DAS software is installed on the PC. For
actual DAS software please contact your local FAE.
The software can also be found on:
DAS website
3.5.1 Serial Connection to PC
After the first connection of USB to a PC the needed driver will be installed automatically. During this there will
be created a new COM port on PC. This COM port can be used to communicate with the board via ASCLIN0 of the
device. Per default the ASCLIN0 is used on P14.0 and P14.1 (e.g. Generic Bootstrap Loader) . In case you will use
the Generic Bootstrap Loader via CAN or ASCLIN0 via P15.2 and P15.3 you must:
– remove R436 and R437 (this disconnect the serial connection from P14.0 and P14.1)
– remove R301 and R302 (this disconnect the CAN0 transceiver from P20.7 and P20.8)
– assemble R438 and R440 with 0R resistor (size 0603) to connect P15.2 and P15.3 to serial connection
– assemble R303 and R304 with 0R resistor (size 0603) to connect P14.0 and P14.1 to CAN0 transceiver
The mentioned resistors are red marked in Figure 3-2.

User Manual 3-4 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
Figure 3-2 Resistors for ASC connection (ASC0)
3.5.2 miniWiggler JDS
The miniWiggler JDS is a low cost debug tool which allows you access to the JTAG of the device. Make sure that
you have the latest DAS release. Debugging is possible via the DAS Server ‘UDAS‘. Please contact your prefered
debug vendor for support of DAS.
If you have connected the board to the PC and there runs the DAS server, then a working connection is visible via
the green ACTIV LED.
The status RUN LED is switched on/off through the DAS Server, depending on the used debugger (client).
IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and X402 (DAP) if the
ACTIV LED is on.
Per default the miniWiggler is connected to the DAP. It is possible to change the connection to DAPE (DAP of
emulation device if available). If resistors R214, R215 and R216 assembled (default) then the standard DAP is
connected to miniWiggler otherwise if R217, R218 and R219 are assembled the the DAPE of enulation device is
connected to miniWiggler. Please note that there should be connected only standard DAP or DAPE. If all this
resistors are not assembled then the miniWiggler can’t be used. In this case only the DAP connectors X402 and
X403 can be used. See Table 3-4 and Table 3-5.
3.6 FlexRay™ (E-RAY)
The board has 2 IDC10 plugs for FlexRay™ Communication (channel A and B) with up to 10 Mbit/s. For the pinout
of the plugs see Figure 6-6. You can use a IDC female connector with crimpconnector, flat cable and SUB-D 9 plug
with crimpconnector to have a 1:1 adapter to SUB-D 9.
The transceiver are connected to the TriCore device via zero ohm resistors (R325 up to R329 and R340 up to R344)
which must be removed to use the ports outside.
C522
RN302
RN301
R243
R241
R239
R237
R235
R233
R231
R224
R219
R218
CB207
R327
R314
R313
R325
R386
R408
R349
R348
R373
R328
R326
R312
D403
R238
R526
R211
CB526
CB525
CB511
CB524
CB523
CB522
CB513
CB203
CB510
CB514
R433
R431
R381
R380
Q301
R252
R250
R251
R253
R254
CB202
R208
CB321
CB320
CB319
CB318
CB317
CB316
CB315
CB314
CB313
CB312
CB311
R215
R214
R524
X405
U306
R521
R240
R242
R223
R370
R371
R379
R387
R383
R389
R388
R365
R364
R363
R362
R360
R212
Q506
CB206
CB310
C304
C311
C310
C306
C309
R449
R448
R447
R445
R443
R413
U405
L402
CB413
C403
R404
C401
R450
R442
R441
CB412
CB411
CB410
C405
C404
R422
R421
U403
Q403
Q402
Q401
R412
C406
R420
R414
R419
R418
R416
R415
R410
R409
CB409
CB407
CB403
R440
R407
U402
R406
R405
CB406
CB404
L503
R305
R306
R308
R309
R315
R316
R318
R319
R522
R301
R311
R341
R321
R322
R222
R220
R221
R525
R523
R533
R323
R343
CB301
CB302
CB205
CB512
CB515
CB516
CB517
CB518
CB520
R537
R307
R317
R538
R534
R513
CB204
CB519
R535
R536
C515
R511
R512
R510
Q502
Q504
Q503
1
X803
1
X804
1
X801
U301U302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
CB309
R303
R304
R338
R330
R331
R358
R350
R351
U303
U304
U305
R332
R334
R333
R352
R353
C519
C520
C521
C407
C408
R320
R213
R216
CB201
R209
R612
R613
R614
R615
R616
R617
U601
U602
U605
1
X805
CB601
CB602
CB603
CB604
CB621
CB622
CB623
CB624 CB625
CB626
CB627
CB628
CB629
CB630
CB631
CB632
R372
1
X802
R438
R437
R436
R417
R340
R503
D502
C511
C512
D501
Q501
Q505
R506
R502
C510
R504
R505
D503
R520
R346
R347

User Manual 3-5 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
ERAY-A can be connected to P14.8, P14.9 and P14.10 (default, usable with ERAY0 and ERAY1) and to P02.0, P02.1
and P02.4 (only usable with ERAY0). Transceiver for channel A can be enabled/disabled via P32.3 (default) or via
P10.2. The error state of transceiver channel A can be read out via P32.2 (default) or via P10.1.
ERAY-B is connected to P14.5, P14.6 and P14.7 (default, usable with ERAY0 and ERAY1). Transceiver for channel A
can be enabled/disabled via P20.10 (default). The error state of transceiver channel A can be read out via P20.9
(default).
For more information look in the user manual for TC3X9.
3.7 Serial Eeprom
The I2C via P15.4 and P15.5 of the TC3X9 is connected to a serial EEPROM with a size of 2KBit (2 x 128 x 8). The
slave address of this EEPROM is 0x50. The upper half of the array (80h-FFh) is permanently write-protected. Write
operations to this address range are inhibited. Read operations are not affected. This upper half contains a pre-
programmed EUI-48™ node address which can be used as MAC ID for Ethernet. The other 128 bytes are writable
by customer.
To disconnect (disable) the EEPROM remove resistor R348 and R349.
3.8 MultiCAN
On the board are two CAN transceiver connected to the CAN0 and CAN1 of TC3X9. The transceivers are connected
to two IDC10 plug. For the pinout of IDC10 plug see Figure 6-7. You can use a IDC female connector with
crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
The transceiver are connected to the TriCore device via zero ohm resistors (R301 up to R304 and R311 up to R314)
which must be removed to use the ports outside.
CAN0 can be used via P20.7 and P20.8 (node 0, default) or P14.0 and P14.1 (node 1). CAN1 can be used via P23.0
and P23.1 (node 0, default) or P00.0 and P00.1 (node 0).
3.9 LIN
On the board is one LIN transceiver connected to the ASCLIN1 on TC3X9 (P15.0 and P15.1). The transceiver are
connected to one IDC10 plug. For the pinout of IDC10 plug see Figure 6-8. You can use a IDC female connector
with crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
To disconnect the LIN remove resistor R364 and R365.
3.10 Ethernet
The TriBoard provide a RJ45 connector (X306) for twisted pair ethernet connections.The TriBoard use a Lantiq
Giagabit PHY PEF7071 as physical interface device. For more information about the ethernet modul see TC3X9
User’s Manual, about the PHY see the PEF7071 datasheet. For the pinout of RJ45 see Figure 6-10.
The PHY is connected to the TriCore device via resistors and resistor arrays (R370 up to R377 and RN301 up to
RN302) which must be removed to use the ports outside.
For the connection between TriCore and PHY can be used RMII (default).
Please note that the RGMII interface can’t be used also if the TriCore device is able to have a RGMII connection.
Therefore Gigabit is not usable with this board only 10M and 100M.
Note: Please note that the PHY is always waked up in RGMII mode and must be reprogrammed to RMII if
needed via MDC and MDIO (P12.0 and P12.1). In the case that you need that the PHY wakeup in RMII then
replace R384 with 3K3 and R385 with 5K1.

User Manual 3-6 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
3.11 HSCT (optional)
The TriBoard provide a footprint of IEEE 1394 socket (X201) for connection to other TC3XX via HSCT.
Note: Don’t use X201 for connection to any IEEE 1394 device,
this can destroy the board and/or the connected device.
For connect two TriBoards you need to assemble this socket (Lumberg 2415 01) on each board and connect the
boards with a standard 6 pin IEEE 1394 cable. For the pinout of socket see Figure 6-9.
3.11.1 High speed with HSCT
For use the HSCT connection between two board you need to remove 5 resistors to have a very short connection
between device and connector. On the TC3X9 Triboard this 5 resistors are R250, R251, R252, R253 and R254 (red
marked in Figure 3-3). This resistors needs to be removed.
mportant: When the resistors are removed then the port signals P20.0, P21.2, P21.3, P21.4 and P21.5 are no
longer available on the 80 pin samtec connectors.
Figure 3-3 Resistors for high speed HSCT
3.12 Other peripherals
For all other peripherals there are no special plugs on the board. The peripheral signals are available on the
different connectors. See “Connector Pin Assignment” on Page 6-1.
C522
RN302
RN301
R243
R241
R239
R237
R235
R233
R231
R224
R219
R218
CB207
R327
R314
R313
R325
R386
R408
R349
R348
R373
R328
R326
R312
D403
R238
R526
R211
CB526
CB525
CB511
CB524
CB523
CB522
CB513
CB203
CB510
CB514
R433
R431
R381
R380
Q301
R252
R250
R251
R253
R254
CB202
R208
CB321
CB320
CB319
CB318
CB317
CB316
CB315
CB314
CB313
CB312
CB311
R215
R214
R524
X405
U306
R521
R240
R242
R223
R370
R371
R379
R387
R383
R389
R388
R365
R364
R363
R362
R360
R212
Q506
CB206
CB310
C304
C311
C310
C306
C309
R449
R448
R447
R445
R443
R413
U405
L402
CB413
C403
R404
C401
R450
R442
R441
CB412
CB411
CB410
C405
C404
R422
R421
U403
Q403
Q402
Q401
R412
C406
R420
R414
R419
R418
R416
R415
R410
R409
CB409
CB407
CB403
R440
R407
U402
R406
R405
CB406
CB404
L503
R305
R306
R308
R309
R315
R316
R318
R319
R522
R301
R311
R341
R321
R322
R222
R220
R221
R525
R523
R533
R323
R343
CB301
CB302
CB205
CB512
CB515
CB516
CB517
CB518
CB520
R537
R307
R317
R538
R534
R513
CB204
CB519
R535
R536
C515
R511
R512
R510
Q502
Q504
Q503
1
X803
1
X804
1
X801
U301U302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
CB309
R303
R304
R338
R330
R331
R358
R350
R351
U303
U304
U305
R332
R334
R333
R352
R353
C519
C520
C521
C407
C408
R320
R213
R216
CB201
R209
R612
R613
R614
R615
R616
R617
U601
U602
U605
1
X805
CB601
CB602
CB603
CB604
CB621
CB622
CB623
CB624 CB625
CB626
CB627
CB628
CB629
CB630
CB631
CB632
R372
1
X802
R438
R437
R436
R417
R340
R503
D502
C511
C512
D501
Q501
Q505
R506
R502
C510
R504
R505
D503
R520
R346
R347

User Manual 3-7 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
3.13 Toggle LED’s
The status LED’s are low active and can be controlled by Software.
Port 20 pin 11 up to pin 14 are connected to single LED’s (D306... D309) and powered by the normal
microcontroller voltage.
Port 33 pin 4 up to pin 7 are connected to single LED’s (D302... D305) and powered by the standby voltage. This
means that this LED’s can be are activ also when the board is in standby mode and only the standby voltage
available (port 33 is powered by VEVRSB pin which is connected to standby supply of TLF35584). In this case the
port pins are controlled by the standby controller if available.
3.14 Buttons
On the board are three buttons.
The reset button (S501) will apply a warm power on reset to the device.
The ENA button (S502) will be used to enable/wakeup the TLF35584.
The P33.11 button (S202) can be used by software as input. Also can this button used by the standby controller
to react on an event when only standby supply is available (e.g. wakeup the TLF35584 via P33.10).
3.15 Debug System
3.15.1 OCDS1
The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port supply of Microcontroller (+5V
default or +3,3V). For pinout of the connector see Figure 6-11. You can connect any debugger to this connector.
The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals in the connector then
assemble R424 and R425 or R426 with a 0R resistor.
If you connect a debug hardware make sure that the miniWiggler JDS (see “miniWiggler JDS” on Page 3-4) is
not activ (ACTIV LED is off) and on the DAP connector (X402) is no hardware connected or the hardware is
tristated.
If the ACTIV LED is on, then stop the active DAS Server ’UDAS’ and/or remove the USB connection to the PC.
In case that R217, R218 and R219 are assembled instead of R214, R215 and R216 then the connector can be used
only for DAP connection to DAPE. If R214 up to R219 not assembled then the connector is not usable.
3.15.2 DAP
The board comes with a DAP connector (X402). For pinout of this connector see Figure 6-12. You can connect a
DAP hardware here. If you use this connector make sure that the miniWiggler JDS is not activ (ACTIV LED is off)
and a connected OCDS1 hardware is disconnected or tristated.
3.15.3 DAPE (only Emulation Device)
The board comes also with another DAP connector (X403) which is connected to DAPE in case that an emulation
device is used. For pinout of this connector see Figure 6-12. You can connect a DAP hardware here. If you use this
connector make sure that the miniWiggler JDS is not activ (ACTIV LED is off) and a connected OCDS1 hardware is
disconnected or tristated in case that R217, R218 and R219 are assembled.

User Manual 3-8 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
3.15.4 High speed with DAP/DAPE
For use the DAP connection with 160 MHz you need to remove 3 resistors to have a very short connection between
device and connector. On the TC3X9 Triboard this 3 resistors are R214, R215 and R216 for DAP or R217, R218 and
R219 for DAPE (red marked in Figure 3-4 and Figure 3-5). This resistors needs to be removed.
Important: When the resistors are removed then only the DAP and DAPE connector on the board can be
used. The on board wiggler and the OCDS1 connector couldn’t be use (are disconnected) in this case, also
the DAP/JTAG part of AGBT connector and the ETK connector couldn’t be used.
All resistors are red marked in the following figures, on TriBoard TC3X9 V1.0 R217 is rotated by 90° and R215 is a
little bit closer to R216.
Figure 3-4 Location of DAP resistors on Top Side
X501
S502
U502
C505
D508
U501
L502
L501
CB501
C502
C507
C509
C508
C501
C503
C504
R501
R507
R508
R509
CB502
X502
1
X702
R611
R610
R609
R620
R618
R619
R602
Q601
1
X705
U604
U603
R604
R606
R608
R607 R605
R603
CB620
CB619
CB618
CB617CB616
CB615 CB614
CB613
CB612
CB611
CB610
CB609
CB608
CB607
1
X701
R398
1
X704
X404
R452
R354
S501
X401
D504 D507
D506
D505
D309 D308 D307 D306 D305 D304 D303 D302
1
X703
X302 X301
T302 T301
R356
R355
R336
R335
R531
R439
C302 C301
R532
R397R396
R395
R394
R393R392
R391
R399
R324
R357 R337
Y201
R207
R206
C202
C201
R202
R201
R428
R427
R426
R425
R424
R344
X402
CB402
R402
R403
CB408
Y401
U401
U404
CB401
R401
D402
L401
BU401
R411
C402
CB405
R423
R429
R430
D401
CB414
CB415
CB416
CB417
CB418
CB419
R444
R446
R454
R456
R455
R451
U406
U407
U408
C303
C305
C307
C308
D301
L301
R359
R361
R382
R384
R385
R374
R378
R230
R232
R234
R236
U307
X303X304X305
F
X306
X201
Y301
R377
4
3
2
1
S201
R375
R376
R601
R390
R329
R453
X403
R203
R204
R205
R217
R255
R256
S202
R225
R226
U201

User Manual 3-9 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
Figure 3-5 Location of DAP resistors on Bottom Side
3.15.5 AGBT (optional)
The TriBoard provide a 22 pin high speed samtec connector (X405) for highest speed connection via AGBT. This
connector should be assembled by your self if needed.
The AGBT interface is only available on emulation devices.
For the pinout of connector see Figure 6-15.
The needed Samtec connector is: ASP-137969-01 (serie ERM8, Nexus HS22).
3.15.6 ETK connector (optional)
The TriBoard provide a 10 pin samtec connector (X404) for connecting to an ETK. This connector should be
assembled by your self if needed.
For the pinout of connector see Figure 6-13.
The needed Samtec connector is: TFM-105-02-A.
3.15.7 EmW Power (optional)
The TriBoard provide the 4 pin power connector (X502) for the Ethernet miniWiggler (EmW). This connector
should be assembled by your self if needed.
For the pinout of connector see Figure 6-14.
The needed Samtec connector is the JST B4B-PH-K.
The connector provide the input voltage to the Ethernet miniWiggler and an enable/wakeup signal connected to
TLF35584 and a standby voltage of +1,25V connected to VDDSB of device. In case the EmW is used you must
C522
RN302
RN301
R243
R241
R239
R237
R235
R233
R231
R224
R219
R218
CB207
R327
R314
R313
R325
R386
R408
R349
R348
R373
R328
R326
R312
D403
R238
R526
R211
CB526
CB525
CB511
CB524
CB523
CB522
CB513
CB203
CB510
CB514
R433
R431
R381
R380
Q301
R252
R250
R251
R253
R254
CB202
R208
CB321
CB320
CB319
CB318
CB317
CB316
CB315
CB314
CB313
CB312
CB311
R215
R214
R524
X405
U306
R521
R240
R242
R223
R370
R371
R379
R387
R383
R389
R388
R365
R364
R363
R362
R360
R212
Q506
CB206
CB310
C304
C311
C310
C306
C309
R449
R448
R447
R445
R443
R413
U405
L402
CB413
C403
R404
C401
R450
R442
R441
CB412
CB411
CB410
C405
C404
R422
R421
U403
Q403
Q402
Q401
R412
C406
R420
R414
R419
R418
R416
R415
R410
R409
CB409
CB407
CB403
R440
R407
U402
R406
R405
CB406
CB404
L503
R305
R306
R308
R309
R315
R316
R318
R319
R522
R301
R311
R341
R321
R322
R222
R220
R221
R525
R523
R533
R323
R343
CB301
CB302
CB205
CB512
CB515
CB516
CB517
CB518
CB520
R537
R307
R317
R538
R534
R513
CB204
CB519
R535
R536
C515
R511
R512
R510
Q502
Q504
Q503
1
X803
1
X804
1
X801
U301U302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
CB309
R303
R304
R338
R330
R331
R358
R350
R351
U303
U304
U305
R332
R334
R333
R352
R353
C519
C520
C521
C407
C408
R320
R213
R216
CB201
R209
R612
R613
R614
R615
R616
R617
U601
U602
U605
1
X805
CB601
CB602
CB603
CB604
CB621
CB622
CB623
CB624 CB625
CB626
CB627
CB628
CB629
CB630
CB631
CB632
R372
1
X802
R438
R437
R436
R417
R340
R503
D502
C511
C512
D501
Q501
Q505
R506
R502
C510
R504
R505
D503
R520
R346
R347

User Manual 3-10 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
remove R522. If R522 is removed then you must make sure that the EmW is always connected. Otherwise with
assembled R522 (default) you should not connect the pin 4 of connector.
The mentioned resistor is red marked in Figure 3-6 and :
Figure 3-6 Resistor for VDDSB on TriBoard TC3X9 TH V1.0(1)
C522
RN302
RN301
R243
R241
R239
R237
R235
R233
R231
R224
R219
R218
CB207
R327
R314
R313
R325
R386
R408
R349
R348
R373
R328
R326
R312
D403
R238
R526
R211
CB526
CB525
CB511
CB524
CB523
CB522
CB513
CB203
CB510
CB514
R433
R431
R381
R380
Q301
R252
R250
R251
R253
R254
CB202
R208
CB321
CB320
CB319
CB318
CB317
CB316
CB315
CB314
CB313
CB312
CB311
R215
R214
R524
X405
U306
R521
R240
R242
R223
R370
R371
R379
R387
R383
R389
R388
R365
R364
R363
R362
R360
R212
Q506
CB206
CB310
C304
C311
C310
C306
C309
R449
R448
R447
R445
R443
R413
U405
L402
CB413
C403
R404
C401
R450
R442
R441
CB412
CB411
CB410
C405
C404
R422
R421
U403
Q403
Q402
Q401
R412
C406
R420
R414
R419
R418
R416
R415
R410
R409
CB409
CB407
CB403
R440
R407
U402
R406
R405
CB406
CB404
L503
R305
R306
R308
R309
R315
R316
R318
R319
R522
R301
R311
R341
R321
R322
R222
R220
R221
R525
R523
R533
R323
R343
CB301
CB302
CB205
CB512
CB515
CB516
CB517
CB518
CB520
R537
R307
R317
R538
R534
R513
CB204
CB519
R535
R536
C515
R511
R512
R510
Q502
Q504
Q503
1
X803
1
X804
1
X801
U301U302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
CB309
R303
R304
R338
R330
R331
R358
R350
R351
U303
U304
U305
R332
R334
R333
R352
R353
C519
C520
C521
C407
C408
R320
R213
R216
CB201
R209
R612
R613
R614
R615
R616
R617
U601
U602
U605
1
X805
CB601
CB602
CB603
CB604
CB621
CB622
CB623
CB624 CB625
CB626
CB627
CB628
CB629
CB630
CB631
CB632
R372
1
X802
R438
R437
R436
R417
R340
R503
D502
C511
C512
D501
Q501
Q505
R506
R502
C510
R504
R505
D503
R520
R346
R347

User Manual 3-11 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Information
Figure 3-7 Resistor for VDDSB on TriBoard TC3X9 V1.0
C522
R347
R346
R520
D503
R505
R504
C510
R502
R506
Q505
Q501
D501
C512
C511
D502
R503
R340
R417
R436
R437
R438
1
X802
R372
CB632
CB631
CB630
CB629
CB628
CB627
CB626
CB625
CB624
CB623
CB622
CB621
CB604
CB603
CB602
CB601
1
X805
U605
U602 U601
R617
R616
R615
R614
R613
R612
R209
CB201
R216
R320
C408
C407
C521
C520
C519
R353
R352
R333
R334
R332
U305
U304 U303
R351
R350
R358
R331
R330
R338
R304
R303
CB309
CB308
CB307
CB306
CB305
CB304
CB303
R342
R302
U302 U301
1
X801
1
X804
1
X803
Q503
Q504
Q502
R510
R512
R511
C515
R536
R535
CB519
R513
R534
R538
R317
R307
R537
CB520
CB518
CB517
CB516 CB515
CB512
CB205
CB302
CB301
R343
R323
R533
R523
R525
R221
R220
R222
R322
R321
R341
R311
R301
R522
R319
R318
R316 R315
R309
R308
R306
R305
L503
CB404
CB406
R405
R406
U402
R407
R440
CB403
CB407
CB409
R409
R410
R415
R416
R418
R419 R414
R420
C406
R412
Q401
Q402
Q403
U403
R421
R422
C404
C405
CB410
CB411
CB412
R441
R442
R450
C401
R404
C403
CB413
L402
U405
R413
R443
R445
R447
R448
R449
C309
C306
C310
C311
C304
CB310
CB206
Q506
R360
R362
R363
R364
R365
R388
R389
R383
R387
R379
R371
R370
R223
R242
R240
R521 U306
X405
R524
R214
R215
CB311
CB312
CB313
CB314
CB315
CB316
CB317
CB318
CB319
CB320
CB321
R208
CB202
R254
R253 R251
R250 R252
Q301
R380
R381
R431
R433
CB514
CB510
CB203
CB513
CB511
R211
R526
R238
D403
R312
R326
R328
R373
R348
R349
R408
R386
R325
R313
R314
R327
CB207
R218
R219
R224
R231
R233
R235
R237
R239
R241
R243
RN301
RN302

User Manual 4-1 V1.2
TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0 2016-08
TriBoard Manual TC3X9
Hardware: TriBoard TC3X9 TH V1.0(1) and TriBoard TC3X9 V1.0
TriBoard Configuration
4 TriBoard Configuration
4.1 HW Boot Configuration
Figure 4-1 HW Configuration DIP-Switches
The picture above shows the definition of the boot HW configuration switch. The meaning of the switches will be
described in the following table (Table 4-1).
Note: The ON position of the switch is equal to a logical LOW at the dedicated pin.
4.1.1 Default Pad State
P14.4 / HWCFG6 is used to select the Default Pad State. Dipswitch 1 used to select this.
In case that dispswitch1 is set to ON then all I/O pins are in tristate otherwise the internal pull-up devices are
enabled on the I/O pins. Please note that after change Dipswitch 1 you must make a power cycle (switch off ->
switch on) to use the new configuration.
In case that TriState is selected (Dipswitch 1 is set to ON) then the I/O pins are floating. If you need a specific level
on different pins during startup (e.g. driver pins) then you must add the needed pull device (up or down). Some
pins (especially the HWCFG pins) haven always the needed external pull-up and/or pull-down resistor assembled
on the board.
4.1.2 Bootmode
Table 4-1 User Startup Modes 1)2)3)
1) The shadowed line indicates the default setting.
2) ’x’ represents the don’t care state.
3) 2 to 4 are the Dip Switch numbers.
HWCFG[5...3] Type of Boot 2 3 4
XX1 Start-up mode is selected by Boot Mode Index X X OFF
110 Internal Start from Flash OFF OFF ON
100 Alternate Boot Mode, Generic Bootstrap Loader on fail (P14.0/P14.1) ON OFF ON
010 Alternate Boot Mode, ASC Bootstrap Loader on fail (P15.2/P15.3) OFF ON ON
000 Generic Bootstrap Loader (P14.0/P14.1) ON ON ON
2
on
134
P14.4 P10.5
P10.6
P14.3