InFocus IN42 Use and care manual

1
IN42 / C445
RS-232C communication
Communication Configuration
To control this projector via RS-232, connect a null modem cable and set the control system serial port
settings to match the following communication configuration:
RS-232 Port Settings
Setting Value
Bits per second 19,200
Data bits 8
Parity None
Stop bits 1
Flow control None
Emulation VT100
Command Format
All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses. The request
can be a read request (indicated by a “?”) or a write request (indicated by 1 to 4 ASCII digits).
A read request example:
(AAA?) where
(starts the command
AAA denotes the command
? denotes the read request)
ends the command
A read command returns the range and the current setting, for example:
Read Command Examples
Function Command Response
Brightness (BRT?) (96-160, 128)
Volume (VOL?) (0-32, 0)
Lamp Hours (LMP?) (0-32766, 42)
A write request example:
(AAA####) where
(starts the command
AAA denotes the command
#### denotes the value to be written
(leading zeros not necessary)
) ends the command
Some commands have ranges, while others are absolute. If a number greater than the maximum range is
received, it is automatically set to the maximum number for that function. If a command is received that is not
understood, a “?” is returned. With absolute settings, “0” is off, 1-9999 is on. The one excep-tion is the Power
command, where 0 is off and 1 is on.
To assure the projector can process a command, wait 3 seconds before enter-ing the next command.

2
IN42 / C445
Write Command Examples
Function Command Response
Brightness (BRT140) Sets the brightness to 140
Power (PWRO) Turns power off
Power (PWRI) Turns power on
Error Conditions
Not all commands are supported for all projectors. If an unsupported com-mand is issued, the command will
be ignored. If a command is received that is not understood, a ‘?’ character will be returned indicating the
command was not understood.
Limitations
The projector cannot respond to commands coming in at a high-rate. There-fore, a delay must occur between
commands to ensure that the command gets properly executed. To assure the projector can process a com-
mand, wait 3 seconds before entering the next command.
The Step column refers to increasing or decreasing the menu bar position since the On-screen Display is not an
exact match of values. For example, Step 2 changes the data by 2 through the CLI (Command Line Interface).
The menu bar is up (or down) by 1.
Function Com-mand Min Max De-fault Step
About (Source Info)
0: n/a
1: enable
ABT at W 0 1 n/a
Active lris
0: Off
1: Presentation
2: Film
IRI at RW 0 2 1
Aspect Ratio
0: Native
1: 16:9
2: 4:3
ARZ at RW 0 2 2
Auto Image
0: n/a
1: enable
AIM at W 0 1 n/a
Auto Power
0: disable
1: enable
APO at RW 0 1 0
Auto Source
0: disable
1: enable
ASC at RW 0 1 1
Blank
0: off
1: on
BLK at RW 0 1 0

3
IN42 / C445
Function Com-mand Min Max De-fault Step
Blank Screen
0: black
1: blue
2: white
BSC at RW 0 2 1
Blue Gain BCG at RW 64 192 128 1
Brightness BRT at RW 96 160 128 1
Ceiling
0: disable
1: enable
CEL at RW 0 1 0
Chime
0: disable
1: enable
ACE at RW 0 1 1
Color CLR at RW 96 160 128 1
Color Space
0: RGB
1: SMPTE240
2: REC709
3: REC601
7: Auto
CSM at RW 0 7 7
Color Temp
0: 9300K
1: 6500K
2: 7200K
3: User
TMP at RW 0 3 2 (computer)
1 (video)
Contrast CON at RW 96 160 128 1
Custom Key (Effect)
0: blank
1: mute
2: aspect ratio
3: source
4: auto image
5: freeze
6: Magnify (Zoom)
7: Source Info
8: Service Info
EFK at RW 0 8 7
Display Messages
0: disable
1: enable
DMG at RW 0 1 1
Factory Reset
0: not reset
1: reset
RST at W 0 1 n/a
Freeze
0: disable
1: enable
FRT at RW 0 1 0
Green Gain GCG at RW 64 192 128 1
Horizontal Keystone DKH at RW 38 218 128 1
Horizontal Position HPS at RW def:-
128 def:+1 28 auto 1
Internal Sound Enable
0: disable
1: enable
INT at RW 0 1 1
IR Receiver front
0: disable
1: enable
IRF at RW 0 1 1

4
IN42 / C445
Function Com-mand Min Max De-fault Step
IR Receiver rear
0: disable
1: enable
IRR at RW 0 1 1
IR Receiver top
0: disable
1: enable
IRT at RW 0 1 0
Language
0= English
1= French
2= German
3= Spanish
7= Portuguese
10= Simplified
Chinese
11= Italian
12= Swedish
LAN at RW 0 12 0
Lamp Hours LMP at R 0 32766 0 1
Lamp Lit
0: not lit
1: lit
LML at R 0 1
Reset Lamp Hours
0: not reset
1: reset
LRT at W 0 1 n/a
Number of Lamp
Resets LMR at R 0 32766 0
Lamp Total On Time
(All Bulbs) LMT at R 0 21474 83646 0
Time In Hours Last
Bulb1 Lasted LBI at R 0 32766 0
Time In Hours Last
Bulb2 Lasted LB2 at R 0 32766 0
Time In Hours Last
Bulb3 Lasted LB3 at R 0 32766 0
Low Power
0: disable
1: enable
LPE at RW 0 1 0
Magnify MAG at RW 0 48 0 1
Magnify Enable
0: disable
1: enable
MGE at RW 0 1 0
Magnify Position
Horizontal (*) MPH at RW 128 896 512 1
Magnify Position
Vertical (*) MPV at RW 96 672 384 1
Menu
0: disable
1: enable
MNU at RW 0 1 0
Menu Navigation
0: up
1: down
4: select
NAV at W 0 4 n/a
Mute
0: disable
1: enable
MTE at RW 0 1 0
(*) Depends on INPUT signal and Magnify value. This is a sample value of
XGA and MAX magnify.

5
IN42 / C445
Function Com-mand Min Max De-fault Step
NND (PC Screen
Saver Off)
0: disable
1: enable
NND at RW 0 1 1
Overscan
0: disable
1: enable
OVS at RW 0 1 0
Phase MSS at RW 0 26 0 1
Power
0: disable
1: enable
PWR at RW 0 1 0
Power Save
0: disable
1: enable
PSV at RW 0 1 0
Power-up Source
0: computer 1
1: computer 2
2: video 1
3: video 2
4: video 3
DSC at RW 0 4 0
Presets
0: presentation
1: photography
2: film
3: video
9: Presets Off
10: user 1
11: user 2
12: user 3
PST at RW 0 12 c:0
v:2
Rear
0: disable
1: enable
REA at RW 0 1 0
Red Gain RCG at RW 64 192 128 1
Reset Filter Hours
0: not reset
1: reset
FRT at W 0 1 n/a
Save User Presets 1
0: not saved
1: saved
US1 at W 0 1 n/a
Save User Presets 2
0: not saved
1: saved
US2 at W 0 1 n/a
Save User Presets 3
0: not saved
1: saved US3 at W 0 1 n/a
Screen Save
0: 5 minutes
1: 10 minutes
2: 15 minutes
3: 20 minutes
4: 25 minutes
5: 30 minutes
SSV at RW 0 5 0
Sharpness
5= Sharpest
6= Sharper
7= Standard
8= Softer
9= Softest
SHP at RW 5 9 7 (computer
and video 1)
6 (video 2
and 3)

6
IN42 / C445
Function Com-mand Min Max De-fault Step
Source
0: computer1
1: computer2
2: video 1
3: video 2
4: video 3
SRC at RW 0 4 0
Source 1
0: computer1
1: computer2
2: video 1
3: video 2
4: video 3
SR1 at RW 0 4 0
Source 2
0: computer1
1: computer2
2: video 1
3: video 2
4: video 3
SR2 at RW 0 4 1
Source 3
0: computer1
1: computer2
2: video 1
3: video 2
4: video 3
SR3 at RW 0 4 2
Source 4
0: computer1
1: computer2
2: video 1
3: video 2
4: video 3
SR4 at RW 0 4 3
Startup Logo
0: blank screen
1: default
2: captured
DSU at RW 0 2 1
Tint TNT at RW 96 160 128 1
Tracking MTS at RW def:
-128 def: +128 auto 1
Unit Total Time On ONL at R 0 21474
83646 0
Vertical Keystone DKC at RW 38 218 128 1
Vertical Position VPS at RW if
def<
128:
0
else:
def
-128
if
def<
128:
defx2
else:
def
+128
auto 1
Video Standard
0: Auto
1: NTSC
2: PAL
3: SECAM
VSU at RW 0 3 0
Volume VOL at RW 0 32 16 1