Ingersoll-Rand SV200 Quick guide

SV200 Installation and Service
Instructions
(Translation of the Original Instructions)
47582535001_US 11/2009 Rev. 0

Introduction
Carefully read these Installation and Service
Instructions prior to the installation and start of
operation of the SV200 rotary valve compressor.
These Installation and Service Instructions de-
scribe the structure and the rst start of operations
of the rotary valve compressor / compressor kits
as well as the service work that needs to be car-
ried out for maintenance/reconditioning.
Make sure that these Installation and Service
Instructions are available to the staff and that work
is performed in accordance with the instructions
therein.
Scope of application of the Installation and
Service Instructions
The Installation and Service Instructions exclu-
sively contain information for the installation, start
of operation and for the maintenance (service) of
the SV200 rotary valve compressor in connection
with the SV200 D and SV200 H compressor kits
respectively.
The Installation and Service Instructions do not
apply for the installation and the service of third
party components through a third party installer.
Target group
These Installation and Service Instructions are lim-
ited exclusively to the utilization through trained
specialists.
Notes and safety instructions
The following notes and safety instructions serve
as a warning about hazards that may lead to oper-
ating errors, injuries and material damage.
Explanation of the signal words
Identies an immediately impending hazardous
situation which may lead to death or serious inju-
ries if it is not averted.
Identies a potential hazardous situation which
may lead to death or serious injuries if it is not
averted.
Identies a potential hazardous situation which
may lead to minor or moderately severe injuries
if it is not averted.
NOTICE
Identies information or company policies that
relate directly or indirectly to the safety of the staff
or the protection of material assets.

Table of Contents
1 General............................................ 1
1.1 Application .............................................. 1
1.2 Manufacturer's address .......................... 1
1.3 Machine data........................................... 1
1.4 Information for enquiries and orders....... 1
1.5 Service locations ..................................... 1
1.6 Technical data of the SV200 rotary
valve compressor .................................... 2
1.7 Dimensions with the utilization of the
optional installation console.................... 4
1.8 Scope of delivery..................................... 5
2 Safety .............................................. 6
2.1 General.................................................... 6
2.2 Authorised personnel, training and
qualication ............................................. 6
2.3 Safety-conscious work............................ 6
2.4 Unauthorised conversions and spare
parts ........................................................ 6
2.5 Incorrect operating methods................... 6
2.6 Disposal................................................... 6
3 Installation guidelines.................... 7
3.1 Internal transportation ............................. 7
3.2 Drive options ........................................... 7
3.3 Preparing installation............................... 8
3.3.1 Rotation direction control /
change of rotation direction............. 8
3.3.2 Installation options for the footers
/ Orientation of the compressor
connections ..................................... 9
3.3.3 Installation site ............................... 10
3.3.4 Selecting the articulated shaft
(only SV200D kit)........................... 11
3.4 Air intake ............................................... 12
3.5 Drive-side facilities ................................ 14
3.5.1 Non-return valve ............................ 14
3.5.2 Safety valve.................................... 15
3.5.3 Non-return valves and safety
valve combination.......................... 15
3.5.4 Micro lter ...................................... 15
3.5.5 Ball valve........................................ 15
3.5.6 Pressure line .................................. 15
3.6 Mounting ............................................... 16
4 Safety labels ................................. 22
5 Initial commissioning................... 24
5.1 General.................................................. 24
5.2 Test run.................................................. 24
5.3 Switching Compressor Off .................... 24
6 Repair/service .............................. 25
6.1 General.................................................. 25
6.2 Personnel and qualication................... 25
6.3 Safety .................................................... 25
6.4 Repair time and scope .......................... 25
6.5 Preparatory work................................... 26
6.6 Repair work ........................................... 26
6.6.1 De-installation / dismantling .......... 26
6.6.2 Assembly / installation................... 30
6.6.3 Measuring / calibration of the
bearing oat................................... 33
6.6.4 Final work....................................... 36
6.7 Required tools ....................................... 37
7 Replacement parts and
ordering......................................... 38

1
D
47582535001_US 11/2009 Rev. 0
1 General
1.1 Application
GHH RAND builds and delivers the SV200 rotary
valve compressor in the form of the SV200 D (Direct
Drive) model as well as the SV200 H (Hydraulic
Drive) model, including the respective accessories
as kits for the installation on tank vehicles for a unit
that is connection-ready.
Due to the oil-free compression of atmospheric air
and the weight-to-power ratio, the compressor
sets are used for the installation on tank vehicles
for the compression-supported emptying of liquids
when the utilization of feed pumps would be dif-
cult or impossible, due to the fact that the direct
contact of liquid / pump would cause problems.
The products built and supplied by GHH RAND are
only designed for the operation at and on utility
vehicles that exclusively drive on paved roads.
A different use requires the consultation with the
manufacturing plant.
1.2 Manufacturer's address
GHH RAND
Schraubenkompressoren GmbH
Max-Planck-Ring 27
46049 Oberhausen
Germany
1.3 Machine data
The machine data is located on the type plate of
the rotary valve compressor.
NOTICE
The entire identication has certicate value and
may not be changed or rendered illegible.
1.4 Information for enquiries and
orders
In conjunction with inquiries and orders of replace-
ment parts and accessories, the exact type iden-
tication and the machine number of the compres-
sor for which the replacement part or accessory is
intended must be indicated.
Original replacement parts and accessories that
are authorized by the manufacturer represent
safety factors.
The use of non-original or non-authorized replace-
ment parts and accessories may void the liability
for the resulting consequences.
1.5 Service locations
Addresses of the service locations can be found
on the last page of these installation instructions
or on the Internet page:
http://www.ghhrand.com

247582535001_US 11/2009 Rev. 0
1.6 Technical data of the SV200 rotary valve compressor
78
100
17 11
281.94
245
120
243.7
160
250
25 g7
50
5
347.94
493.7
A8x7x40 DIN 6885
232
10
68
8 x 11 18010
M10 18
40
All measurements are approximate specications.
232
10
5
50
243.7
296 250
120
89.8
146
89.8
546
A8x7x40 DIN6885
160
25 g7
281.94
347.94
8 x 11
10 180
6xM 12/1912
All measurements are approximate specications.
Model: SV200 D(direct drive)
Model: SV200 H(hydraulic drive)
Flange dimensions refer to SV200 D model

3
D
47582535001_US 11/2009 Rev. 0
Dimensions & weight
SV200… …D …H
Length (approx.) mm 494 546
Width (approx.) mm 232 232
Height (approx.) mm 245 245
Weight (approx.) kg 37 39
Connection dimensions
Intake-/pressure ange: DN40 / Ø68 - 2 x M10
Articulated shaft:
Only articulated shafts with two joints are permitted.
Only balanced articulated shafts with a balancing quality of G 6.3 in
accordance with DIN ISO 1940 with length compensation may be
used.
Performance data
Unit SV200
Rotary valve compressor min-1 [rpm] 1000 1400 1800
Working gage pressure bar (g) [psig] 1.5 [15.0]
Intake volume m³/h [cfm] 75 [50] 119 [76] 163 [102]
Coupling output kW [hp] 5.0 [5.5] 7.1 [8.1] 9.8 [11.1]
Final temperature °C [°F] 136 [229] 133 [231] 142 [247]
Intake temperature max. °C [°F] 46 [115] 46 [115] 46 [115]
Working gage pressure bar (g) [psig] 2.0 [25.0]
Intake volume m³/h [cfm] 65 [42] 109 [67] 152 [93]
Coupling output kW [hp] 6.0 [7.3] 8.2 [10.1] 11.3 [14.0]
Final temperature °C [°F] 164 [299] 157 [290] 166 [306]
Intake temperature max. °C [°F] 46 [115] 46 [115] 46 [115]
Working gage pressure bar (g) [psig] 2.5 [36.0]
Intake volume m³/h [cfm] 55 [32] 98 [58] 140 [83]
Coupling output kW [hp] 7.0 [9.3] 9.3 [12.4] 12.9 [17.2]
Final temperature °C [°F] 192 [375] 181 [356] 190 [372]
Intake temperature max. °C [°F] 46 [115] 46 [115] 46 [115]
Final temperature with max.
intake temperature °C [°F] 240 [464] 227 [441] 238 [460]
All information for:
Feed medium: atmospheric air
Intake pressure: 1 bar (abs.) [14.504 psia]
Intake temperature: 20 °C [68 °F]
Technical data without intake or pressure losses
Maximum operating pressure:
2.5 bar (rel.) [36 psig]
Environmental conditions
Environmental temperature:
–25 to +46 °C [-13 to +111.8 °F]
Rotational speed range
SV200
min. min-1/rpm 1000
max. min-1/rpm 1800

447582535001_US 11/2009 Rev. 0
1.7 Dimensions with the utilization of the optional installation console
3°
350
250
600
58
100
510
216
All measurements are approximate specications.
Dimensions
SV200 D/H with kit... ...D ...H
Length (approx.) mm 510 546*
Width (approx.) mm 250 (+58)
Height (approx.) mm 358**
*Length without hydraulic motor (optional)
** Measurement from bottom edge of vehicle
frame (with use of the optionally deliverable
installation console; console can be short-
ened on the top)
Sample illustration for SV200 D model

5
D
47582535001_US 11/2009 Rev. 0
1.8 Scope of delivery
Scope of delivery SV200 D kit
- SV200 D compressor
- 2 ange seals for intake and pressure ange at
the compressor
- 1 articulated shaft ange (DIN or SAE)
- Air intake lter kit
(intake lter with rain cap, mounting rubber pipe
elbow [90°], pipe piece (aluminum), 4 hose
clamps, service gage and hose connection tting
DN50 [straight / optional: 90° ungulate and pivot-
able])
- Spiral hose (length: approx. 1.5m)
- Drive-side ange (pipe connection ange / weld
ange)
- 1 check valve and 1 safety valve or 1 combined
check/ safety valve
Optional:
- Overload coupling with shear bolt, usable for DIN
and SAE-articulated shaft ange (incl. 2 shear
bolt as backup)
- Installation console with compressor mount and
mounting material
- Micro lter (for drive-side installation)
Scope of delivery SV200 H kit
- SV200 H compressor
- 2 ange seals for intake and pressure ange at
the compressor
- 1 exible shaft connection (coupling)
- Air intake lter kit
(intake lter with rain cap, mounting rubber pipe
elbow [90°], pipe piece (aluminum), 4 hose
clamps, service gage and hose connection tting
DN50 [straight / optional: 90° ungulate and pivot-
able])
- Spiral hose (length: approx. 1.5m)
- Drive-side ange (pipe connection ange / weld
ange)
- 1 non-return valve and 1 safety valve or 1 com-
bined non-return/ safety valve
Optional:
- Installation console with compressor mount and
mounting material
- Hydraulic motor
- Micro lter (for drive-side installation)

647582535001_US 11/2009 Rev. 0
2 Safety
2.1 General
These Installation and Service Instructions include
basic notes that must be followed during the
assembly, installation, and service. Therefore,
these Installation and Service Instructions must be
read in their entirely by the responsible specialized
staff prior to the start of work.
2.2 Authorised personnel, training
and qualication
Installation work on the compressor / compres-
sor kit may only be carried out by authorized,
trained and qualied persons who are familiar
with the applicable safety regulations.
Repair work or modications may only be per-
formed by authorized personnel. The staff is avail-
able at anytime at the service sites or at
GHH RAND.
2.3 Safety-conscious work
The safety-related regulations that are relevant for
the installation, operation and maintenance of air
compressors can be found in the following publi-
cations:
Standards, in particular:
DIN EN ISO
12100
Safety of machinery
DIN EN
1012-01
Compressors and vacuum pumps,
safety requirements
In addition, the following regulations and guidelines
must be adhered to
– Product-related safety data sheets, especially in
regard to explosion hazards, handling and stor-
age
– Technical rules for hazardous materials (TRHM)
– Technical rules for operational safety (TROS)
In this context, the respectively last applicable ver-
sions of these regulations shall be authoritative.
Special legal provisions and regulations, particu-
larly safety regulations, that may apply in your
company or due to local conditions must also be
adhered to.
In case of competing regulations, the more
restrictive provisions shall be applied.
Also adhere to the national regulations that apply
in the respective country in which the installation
takes place.
2.4 Unauthorised conversions and
spare parts
Modication and changes on the compressor /
compressor kit are prohibited.
Damage to the seal will void any warranty
claims.
Original replacement parts and accessories that
are authorized by the manufacturer represent safe-
ty factors.
The use of non-original or unauthorized replace-
ment and accessory parts may void the liability for
resulting consequences.
2.5 Incorrect operating methods
Without the approval of GHH RAND, compressors
/ compressor kits may not be operated under any
other conditions than those listed in Chapter 1.6
"Technical data".
The operation of compressors / compressor kits
under conditions that are not intended may lead
to serious injuries and signicant material dam-
age.
2.6 Disposal
NOTICE
Properly dispose of operating materials and com-
ponents in an environmentally-safe way.

7
D
47582535001_US 11/2009 Rev. 0
3 Installation guidelines
NOTICE
In principle, the installation guidelines of the man-
ufacturer for the respective vehicle must be
adhered to in addition to the specications of this
Installation and Service Instruction.
3.1 Internal transportation
The rotary valve compressor and the accessories
are delivered separately.
The rotary valve compressor sits on a pallet and is
fastened with tension straps.
The additional parts of the kit are delivered in a
separate box.
Use a sufciently dimensioned lift truck or forklift
for the internal transport.
1
To transport the compressor with a crane, it is pos-
sible to screw an eye bolt (1) into the threaded drill
hole between the connection anges on the top of
the compressor.
Use sufciently dimensioned lifting accessories.
Do not lift the compressor by the plastic covers
that are attached to the sides.
3.2 Drive options
No radial forces may be transmitted to the drive
shaft of the compressor; actuation with a V-belt
drive is therefore prohibited.
To avoid damage to the compressor, it must be
ensured that the required operating speed is
achieved promptly.
SV200D kit (D : direct drive)
The SV200 D rotary valve compressor that is sup-
plied with the kit is intended for a direct actuation
from a power take-off via a articulated shaft.
The installation of a safety coupling is recommend-
ed for the protection of the drive (gear unit).
An overload coupling with shear bolt can be sup-
plied as an option (refer to Chapter 1.8).
SV200H kit (H : hydraulic drive)
The SV200 H rotary valve compressor that comes
with the kit is intended for an actuation through a
hydraulic motor via a exible coupling.
It is possible to attach a hydraulic motor, which
can be supplied as an option, through a ange at
the cover on the drive side of the compressor; the
drive shafts are connected with each other via the
exible coupling.

847582535001_US 11/2009 Rev. 0
3.3 Preparing installation
3.3.1 Rotation direction control / change
of rotation direction
The rotary valve compressor may only be turned
in the direction as indicated by the arrow (1) on
the casing.
Even short-term turning against the stipulated
rotation direction can result in major damage to
the compressor.
1
• Check the rotation direction of the drive:
The arrow (1) in the compressor casing indicates
the required rotation direction of the drive
shaft.
If the rotation direction of the compressor is not
the same as the rotation direction of the drive, the
rotation direction of the compressor must be
changed by switching the covers to the respective
other side.
Exchanging of the covers:
3
1
4
2
6
5
• Unscrew the hexagon socket screws (1) [total of
4], take footer (4) and cover (6) off the compres-
sor (3).
• Take tted key (5) out of the shaft and insert it
into the slot at the other end of the shaft.
The tted key slot in the shaft has sharp edges.
Wear appropriate protective gloves.
• Reinstall the covers on the opposite ends.
Apply installation paste (ceramic based, heat
resistant up to +250°C) to the hexagon socket
screws (1), insert them and tighten them with the
specied torque.
Tightening torque (M10 10.9):
58 Nm/42.8lbfft

9
D
47582535001_US 11/2009 Rev. 0
Do not use washers on the cover for the hydrau-
lic drive (only SV200 H).
Do not tighten hexagon socket screws applying
more than the specied torque, because the com-
pressor housing may otherwise be damaged.
The powering now takes place at the other end of
the shaft of the compressor, the drive rotation
direction is running counter-clockwise.
NOTICE
Prior to the reattachment of the footers it needs
to be determined which direction the connection
anges of the compressor should point to in the
installed condition, because the footers can
optionally be installed so that they are off-set on
the compressor by 90° respectively, see Section
3.3.2.
in conjunction with a change of the drive rotation
direction it needs to be ensured that afterwards
the anges for the installation of the vacuum and
the pressure line are located on the respectively
opposite side.
3.3.2 Installation options for the footers /
Orientation of the compressor con-
nections
4
1
23
5
The attachment footers (3) can be installed so that
they are offset respectively by 90° between 2 fas-
tening screws (4) of the covers (1) (installation posi-
tion see Pos. 5).
If necessary, the footers can also be installed on
the compressor so that they are turned by 180°
(see Pos. 2) to achieve a closer spacing of the
mounting drill holes on the vehicle.
Do not use washers at the mounting points of the
footers.
No washers are used either for the other two
mounting screws on the cover for the hydraulic
drive (only SV200 H).
NOTICE
If the optional installation console is used, a
mounting plate is installed in lieu of the footers.
The mounting plate is screwed to the installation
console which is attached to the vehicle, see
Chapter 3.6.

10 47582535001_US 11/2009 Rev. 0
3.3.3 Installation site
The approximate position of the compressor on
the vehicle must be determined prior to the instal-
lation considering the following framework condi-
tions.
Required space conditions
• Check required space on the vehicle considering
the respective dimensions (see Chapter 1.6
"Technical data for SV200 rotary valve compres-
sor" and Chapter 1.7).
• To ensure sufcient cooling of the compressor,
the space between the front covers and other
parts should measure at least 20 cm.
• Consider the orientation of the compressor and
the respective space requirement for the con-
nection of the intake and the pressure line.
Orientation / ange parallelism
max.10° max.10°
NOTICE
The maximum permissible inclined position of the
rotary valve compressor in longitudinal direction
during the operation is +/–10°.
For the SV200D compressor, plan, if possible, for
an installation and orientation on the side of the
power take-off in a right angle to the vehicle.
The optional installation console already comes
with a ange tting of 3 ° to achieve ange paral-
lelism (see illustration in Chapter 1.7 "Measure-
ments in conjunction with the use of the optional
installation console").

11
D
47582535001_US 11/2009 Rev. 0
3.3.4 Selecting the articulated shaft (only
SV200D kit)
Consider the following items during the determi-
nation of the articulated shaft:
• Choose the appropriate length for the jointed
shaft taking into consideration the tting dimen-
sions and observing the maximum extension
length.
The maximum permissible expansion length of
the articulated shaft must be looked up in the
operating instructions of the articulated shaft
manufacturer and must be adhered to during the
installation.
As a matter of principal, the manufacturer's struc-
tural guidelines for the respective vehicle and the
technical information provided by the articulated
shaft manufacturer in regard to the mounting,
ange parallelism and inclination angle of the
articulated shaft must be adhered to.
The total inclination angle of the articulated shaft
shall not exceed 12°. 15° are permissible in excep-
tional cases.

12 47582535001_US 11/2009 Rev. 0
3.4 Air intake
Component overview
1
2
343
5
67
3
8
9
10
6
3
Air lter Spiral hose
Rubber pipe angle (90°) Hose connection ttings, straight
Hose clamp Hose connection ttings, 90°, pivotable
(optional, instead of Pos. 7)
Service gage Flange seal
Pipe piece Intake ange on the compressor

13
D
47582535001_US 11/2009 Rev. 0
The intake air must be cleaned through the air lter
that is included in the kit. A paper lter should be
chosen as the lter material.
Air ow / lter installation location
The air intake must not be located in the area of
warm air or emitted hot exhaust fumes. If neces-
sary, the exhaust system of the vehicle or the
installation location of the air filter must be
moved.
Temperature damage may be caused to the com-
pressor in case of non-adherence.
Connection line, service gage
The air intake line (spiral hose included in the kit)
is connected to the air lter via a 90° elbow tting
which the intake service gage is mounted onto.
NOTICE
Consider the accessibility and readability of the
service gage when determining the installation
location of the air lter.
The connection of the air intake line at the com-
pressor takes place via a hose connector tting
(straight or with 90° angle and pivotable).
NOTICE
To prevent a loss of pressure, the nominal width
(DN 50) of the connection line for the air intake
lter may not be reduced, and the length of the
connection line should be kept as short as pos-
sible.
If a xed piping is intended in lieu of the spiral
hose, it needs to be ensured that only pipes made
of non-corroding material (e.g. aluminum) are
used.
Otherwise there is a risk that rust germs may enter
the compressor and that the rotor may start to
rust.
Only the non-electricity conductive ange seals
that come with the kit may be used on the com-
pressor anges - risk of corrosion!

14 47582535001_US 11/2009 Rev. 0
The connection of the pressure line at the com-
pressor takes place via the pipe connection ange
that came with the kit of the welding ange (option-
al)
3.5.1 Non-return valve
The non-return valve that is included in the kit must
be installed in the pressure line to the tank as a
means of protection for the compressor.
The non-return valve is to prevent a reverse motion
of the rotary valve compressor.
It is not used to prevent material rebounds; for that,
respective features must exist on the vehicle
side.
Adhere to the ow direction of the non-return
valve (arrow in the casing). Do not mount the
safety valve facing downwards.
NOTICE
The non-return valve that is installed in the com-
pressor kit has the purpose to prevent a longer
fast reverse motion of the compressor after shut-
off that is due to an existing residual pressure in
the air pressure lines of the pneumatic system as
well as in the tank.
3.5 Drive-side facilities
Component overview
1
3
2
4
5
6
8
9
7
SV200 Rotary valve compressor Safety valve
Flange seal Non-return valve
Pipe connection ange Combined non-return valve and safety
valve (in lieu of Pos. 6 and 7)
Weld ange Micro lter (optional)
Pressure line
(not included in the total price)