The controller can be programmed with
OptiSet Plus temperature profiles that
allow the user to select named products
and/or numeric setpoints. See the
appropriate Operator’s Manual for more
detailed information about using
OptiSet Plus.
To select or change a numeric setpoint
complete the following steps. This
example shows the Standard Display
with the PRODUCT/SETPOINT soft key.
Using the Standard Display with the
SETPOINT soft key is basically the same
but some of the screens differ slightly.
OPTISET PLUS SELECTING A NUMERIC SETPOINT SELECTING A NAMED PRODUCT
To select or change a numeric setpoint
complete the following steps. This
example shows the Standard Display
with the PRODUCT/SETPOINT soft key.
Using the Standard Display with the
SETPOINT soft key is basically the same
but some of the screens differ slightly.
1 1
2 2
4 4
6 6
7
7
NOTE: Alarm Code 127, Setpoint Not Entered, may be generated if the + or - soft keys
are used to change the numeric setpoint or named product, but the YES or NO soft keys
are not used to accept or decline the new setting within 10 seconds.
NOTE: If no keys are pressed for 30 seconds while in the Named Product Changer
Screens, the HMI will return to the Standard Display.
NOTE: If no keys are pressed for 30 seconds while in the Named Product Changer
Screens, the HMI will return to the Standard Display.
NOTE: In OptiSet Plus the terms “numeric setpoint” and “setpoint” mean the same
thing and are displayed as numbers. The terms “named product” and “product” mean
the same thing and are displayed as words.
NOTE: Pressing the EXIT soft key at any point will return to the Standard Display. NOTE: Pressing the EXIT soft key at any point will return to the Standard Display.
• Numeric Setpoint - If the
controller does not have named
products loaded, the far left
soft key will display SETPOINT
as shown below. This is the
factory default setting. Change
the numeric setpoint like you
normally would on an SR-2
Controller.
• Named Products - The
controller can be programmed
to allow only named products
to be selected. In which case
the far left soft key will display
PRODUCT as shown below.
1. Begin at the Standard Display. If
the Temperature Watch Display
is showing, press the MENU soft
key once to return to the Standard
Display.
2. Press the PRODUCT/SETPOINT
(or SETPOINT) soft key on the
Standard Display.
3. The “Named Product / Numeric
Setpoint?” Screen briefly appears,
then the “Named Product or
Numeric Setpoint?” Screen will
appear.
4. Press the NUMERIC soft key.
5. The “Setpoint” Screen briefly
appears, then the “Current Setpoint
Is” Screen will appear.
6. Press the + or - soft keys to change
the setpoint.
7. Press the YES soft key to select the
new setpoint.
• If the NO key is pressed the
setpoint change selected with
the + or - soft keys will not be
accepted, the setpoint will not
1. Begin at the Standard Display.
If the Temperature Watch Display
is showing, press the MENU soft
key once to return to the Standard
Display.
2. Press the PRODUCT/SETPOINT
(or PRODUCT) soft key on the
Standard Display.
3. The “Named Product / Numeric
Setpoint?” (or Named Product)
Screen briefly appears, then the
“Named Product or Numeric
Setpoint?” (or Named Product)
Screen will appear.
4. Press the NAMED soft key.
5. The “Product” Screen briefly
appears, then the “Current Product
Is” Screen will appear.
6. Press the + or - soft keys to change
the named product.
7. Press the YES soft key to select the
new named product.
• If the NO key is pressed the
named product change selected
with the + or - soft keys will
Named products can have a single setpoint, or they can have a setpoint range
that allows the user to select a setpoint within that range.
• Named Products or Numeric Setpoint -The controller can be programmed
to allow named products or numeric setpoints to be selected. In which case
the far left soft key will display PRODUCT/SETPOINT as shown below.
be changed and the display will return to the Standard Display.
• If the YES soft key is pressed, the setpoint change selected with the + or -
soft keys will be accepted, and the following screens will appear
8. The “Programming New Setpoint” Screen will briefly appear.
9. The “New Setpoint Is 40” Screen briefly appears.
10. The Standard Display appears with the new setpoint.
not be accepted, the named product will not be changed and the display will
return to the Standard Display. (Over)
• If the YES soft key is pressed, the named product change selected with the +
or - soft keys will be accepted, and the following screens will appear.
8. The “Programming Named Product” Screen will briefly appear. NOTE: If the
“Change Setpoint for Potatoes” Screen briefly appears, the named product
has been programmed with a setpoint range. See “Selecting the Setpoint for a
Named Product” below.
9. The “New Named Product Is Potatoes” Screen briefly appears.
10. The Standard Display appears with the new named product.
