Ingersoll-Rand BRITON 2003V.SES Operating and maintenance manual

30
46
20
68
25
225
105
54

31 16
225
105
25
68
30
46
20
54

16
31
C/LINE
OF HINGE
SIZE 1-4 ADJUSTABLE BACKCHECK CLOSER
IF NECESSARY ADJUST
POWER AND DOOR SPEEDS
66
FOR TRANSOM AND PARALLEL ARM INSTALLATION PROCEDURE SEE OVERLEAF
Check that the door closer closes the door correctly and fixing screws are tight. Periodically apply light oil to arm knuckle joints and door hinges.
MAINTENANCE (Quarterly)
NOTE - all dimensions
are in millimetres
R.H. DOOR
PULL SIDE - REGULAR APPLICATION (FIG. 1)
ANGLE OF OPENING 180°SUBJECT TO HINGE & SURROUNDING STRUCTURE
L.H. DOOR
2110/103/00
ISSUE A
WARNING
DOOR CLOSER POWER #1 & 2 AND THOSE SUPPLIED
WITH MECHANICAL HOLD OPEN DEVICES MUST NOT BE
INSTALLED ON FIRE / SMOKE DOORS.
OPEN DOOR TO ENGAGE SECONDARY ARM STRIP AND TUBE
CLOSE DOOR AND SET SECONDARY ARM AT 90°TO DOOR FACE
SECURELY TIGHTEN CLAMP BOLT WITH SPANNER
55
PEEL TEMPLATES OFF BACKING PAPER
POSITION ON DOOR/FRAME
PILOT DRILL 7 HOLES
11
FIT COVER TO CLOSER
FOLLOWING STEPS SHOWN
(2 SCREWS)
77
LOCATE MECHANISM ASSEMBLY ON
BACKPLATE AND SECURE (2 SCREWS)
44
L. H. door
225
232
25
46
38 20 16
113
16 20
232
225
25
38
46
C/LINE
OF HINGE
113
R. H. door L. H. door
A
A
BB
C
C
C
C
25
20
46 232
38
225
113
16
232
225
25
20
16
46
38
113
FIT BACKPLATE (3 SCREWS)
FIT BRACKET ASSEMBLY (2 SCREWS)
PEEL OFF TEMPLATES
22
FIT MAIN ARM ASSEMBLY TO MECHANISM (90°)
SECURELY TIGHTEN FIXING SCREW
33
R. H. door L. H. door R. H. door
90°90°
90°
1
2
LATCH
DOOR SPEED
3
1
2
POWER (FIG.1)
FACTORY SET TO SIZE 3
CLOSER
POWER SIZE
NUMBER
OF TURNS
(APPROX)
1
2
3
4
-6
-3
0
+5
REGULAR FIXING (FIG.1)PARALLEL ARM FIXING (FIG.66)
POWER SIZE 1 - 4 POWER SIZE 1 - 3
TRANSOM FIXING (FIG.61)
POWER SIZE 1 - 4
CLOSER
POWER
DOOR
SIZE
#2
40kg
850
MAX
#1
20kg
750
MAX
#3
60kg
950
MAX
#4
80kg
1100
MAX
OPTIONAL
COVERS
STANDARD
COVER
90°
3
4mm
BACKCHECK

L.H. DOOR R.H. DOOR L.H. DOOR R.H. DOOR
PUSH SIDE - PARALLEL ARM APPLICATION (FIG.66) PUSH SIDE TRANSOM APPLICATION (FIG.61)
MARK OUT DOOR/FRAME AS DETAILED OVERLEAF
PILOT DRILL 9 HOLES
11
MARK OUT DOOR/FRAME AS DETAILED OVERLEAF
PILOT DRILL 7 HOLES
11
ANGLE OF OPENING 180°SUBJECT TO HINGE & SURROUNDING STRUCTURE ANGLE OF OPENING 180°SUBJECT TO HINGE & SURROUNDING STRUCTURE
FIT MAIN ARM ASSEMBLY TO MECHANISM (90°)
SECURELY TIGHTEN FIXING SCREW
33
FIT MAIN ARM ASSEMBLY TO MECHANISM (30°)
SECURELY TIGHTEN FIXING SCREW
33
90°90°
FIT COVER
7
A
A
BB
C
C
C
C
LOCATE MECHANISM ASSEMBLY ON BACKPLATE
AND SECURE (2 SCREWS)
44
FULLY CLOSE DOOR SPEED AND LATCH REGULATORS
PULL MAIN ARM FORWARD, LOCATE MECHANSIM ASSEMBLY ON
BACKPLATE AND SECURE (2 SCREWS)
44
IF NECESSARY ADJUST POWER AND DOOR SPEEDS
66
FIT BACKPLATE (3 SCREWS)
FIT ARM BRACKET ASSEMBLY TO FIG.66 BRACKET (2 SCREWS)
FIT BRACKET ASSEMBLY TO FRAME (4 SCREWS)
22
FIT BACKPLATE (3 SCREWS)
FIT ARM BRACKET ASSEMBLY (2 SCREWS)
22
C
C
B
A
A
C
OPEN DOOR TO ENGAGE SECONDARY ARM STRIP AND TUBE
CLOSE DOOR AND SET MAIN ARM PARALLEL TO DOOR FACE
SECURELY TIGHTEN CLAMP BOLT WITH SPANNER
55
OPEN DOOR TO ENGAGE SECONDARY ARM STRIP AND TUBE
CLOSE DOOR AND SET SECONDARY ARM AT 90°TO DOOR FACE
SECURELY TIGHTEN CLAMP BOLT WITH SPANNER
55
30º30º
C
B
90°90°
1
2
LATCH
DOOR SPEED
3
4mm
BACKCHECK
3
1
2
POWER (FIG.61)
FACTORY SET TO SIZE 3
CLOSER
POWER SIZE
NUMBER
OF TURNS
(APPROX)
1
2
3
4
-5
-3
0
+5
POWER (FIG.66)
FACTORY SET TO SIZE 3
CLOSER
POWER SIZE
NUMBER
OF TURNS
(APPROX)
1
2
3
3+
-6
-3
0
+5
OPTIONAL COVERSSTANDARD COVER OPTIONAL COVERSSTANDARD COVER
FIT COVER TO CLOSER FOLLOWING STEPS SHOWN (2 SCREWS)
77
FIT COVER TO CLOSER FOLLOWING STEPS SHOWN (2 SCREWS)
77