Inhep Digital Security IDS 1200 User guide

2 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
Summary of Operation
mrasid/mrA ]#[ +]EDOCRESU[
mrAyawAkciuQ
nwoddloH ]1[ dnoces1rof
mrAyatSkciuQ
nwoddloH ]5[ dnoces1rof
oG&mrAyatSkciuQ
nwoddloH ]6[ dnoces1rof
lenaPybrewsnAdecroF ]8[
demrasidebtsummetsyS-
cinaP
nwoddloH ]P[ dnoces1rof
eriF
nwoddloH ]F[ dnoces1rof
ycnegremElacideM
nwoddloH ]M[ dnoces1rof
yromeMmralA
nwoddloH ]0[ dnoces1rof
snoititraPegnahC
nwoddloH ]EDOM[ +dnoces1rof ]REBMUNNOITITRAP[ +[!!
!
!!]
enozassapyB
nwoddloH ]9[ +dnoces1rof [ ]REBMUNENOZ +[!!
!
!!]+]#[
enozemihcmargorP
nwoddloH ]2[ +dnoces1rof [ ]REBMUNENOZ +[!!
!
!!]+]#[
enozyatsmargorP
nwoddloH ]3[ +dnoces1rof [ ]REBMUNENOZ +[!!
!
!!]+]#[
enozzzubmargorP
nwoddloH ]4[ +dnoces1rof [ ]REBMUNENOZ +[!!
!
!!]+]#[
sutatSelbuorTweiV
nwoddloH ]7[ +dnoces1rof ]#[
sseruD ]#[ +]EDOCSSERUD[
01egapeeS-ediuGgnimmargorProF

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 3
IDS1200 INSTALLER MANUAL
Contents
1. Introduction to the IDS1200............................................................................................ 5
1.1 Features ............................................................................................................................ 5
2. Installation and Wiring .................................................................................................... 5
3. End-of-Line Resistors/Tamper per Zone ...................................................................... 6
4. Connecting the Telephone Communicator .................................................................. 7
5. Programmable Outputs ................................................................................................... 8
6. The Key-Switch or Remote Control Unit ...................................................................... 8
7. Additional Technical Data ............................................................................................... 8
8. Hardware Reset Switch .................................................................................................. 9
9. Event Log ......................................................................................................................... 9
10. Programming Instructions ............................................................................................ 10
10.1 Introduction ...................................................................................................................... 10
10.2 Location Values ................................................................................................................ 10
10.3 Programming the Panel ....................................................................................................11
10.4 Program Location Summary ........................................................................................... 12
11. Index ............................................................................................................................... 43
12. Programming Tables ..................................................................................................... 49
Figures
Figure 1: Connection Diagram............................................................................................... 6
Figure 2: Tamper per Zone Connection ............................................................................... 7
Figure 3: Resistors used for Tamper per Zone ................................................................... 7
Figure 4: Programmable Output Configuration ................................................................... 8

4 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
Tables
Table 1: Value represented by each zone indicator ............................................................ 10
Table 2: Binary Representation ............................................................................................. 10
Table 3: Location / Zone Defaults .......................................................................................... 12
Table 4: Programmable Zone Types ...................................................................................... 13
Table 5: Standard Contact ID reporting codes .................................................................... 20
Table 6: Alarm reporting codes.............................................................................................. 21
Table 7: Programmable O/P Program Values ....................................................................... 29
Table 8: Location Default Values (Loc. 675 - 679) ................................................................ 29
Table 9: Location Default Values (Loc. 683 - 694) ................................................................ 30
Table 10: Location Default Values (Loc. 695 - 702) .............................................................. 30
Table 11: Location Descriptions (Loc. 708 - 712) ................................................................. 31
Table 12: Location Default Values (Loc. 960 - 964) .............................................................. 36
Table 13: Location Default Values (Loc. 968 - 975) .............................................................. 37

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 5
IDS1200 INSTALLER MANUAL
1. Introduction to the IDS1200
The IDS1200 is a versatile, state of the art, microprocessor based, twelve zone alarm panel. Most features
are optional and may be programmed either directly through the keypad or via the telephone system, using
the IDS download software and appropriate modem. There are twelve programmable burglary zones, siren,
auxiliary power outputs and 5 outputs which may be programmed to perform various trigger/switching
functions.
For correct operation the IDS1200 must be used in conjunction with the specified transformer/battery
combination and peripheral sensors and signalling devices.
1.1 Features
!Two programmable partitions to which zones can be allocated.
!Four wire keypad operation - up to a maximum of 5 keypads.
!Twelve, fully programmable, end-of-line (3K3) supervised zones, and 1 dedicated panic zone per keypad
which is not end-of-line supervised.
!Optional tamper reporting per zone using double end-of-line resistors (12K and 4K7).
!Fully programmable digital telephone communicator which supports most industry standard formats.
!Five programmable trigger outputs.
!Non volatile EEPROM memory retains all program and event log data in the event of a total power
failure.
!Programmable loop response time.
!Up and downloadable using IDS windows based software.
!Excellent protection against lightning (provided by specialised “zap tracking” and transient
suppressors).
!Auto-arm - partitions can be programmed to arm daily at a pre-determined time.
!Event log (300 events) date and time stamped.
!Fax defeat allows download access to the panel with other devices connected to the phone line.
!Dual reporting provides for duplicated reporting to two independent central base stations.
!Programmable silent or audible panic.
2. Installation and Wiring
Please refer to Figure 1: Connection Diagram and familiarise yourself with the following sections.

6 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
Figure 1: Connection Diagram - without tamper per zone
3. End-of-Line Resistors/Tamper per Zone
!All zones are end-of-line supervised. Any unused zones must also be terminated with the appropriate
resistor.
!The end-of-line resistor should be placed inside or as close to the sensor as possible.
!If the zones are not programmed to report tamper by zone i.e. a [0] is programmed into location 1283
then use the 3K3 end-of-lineresistor.
EARTH
EARTH
LINE
LINE
PHONE
TELKOM
Keypad
D-
D+
Zone 12
Zone 11
Zone 10
Zone 9
Zone 8
Zone 7
Zone 6
Zone 5
Zone 4
Zone 3
Zone 2
Zone 1
+
+
+
+
AC
Radio
A
U
X
I
L
I
A
R
Y
1
2
3
4
5A
U
X
I
L
I
A
R
Y
O
U
T
P
U
T
S
SW1
Hardware
Reset
Switch
FU1 Battery
4 AMP
FU2 Auxilliary
Power Fuse
1 AMP
FU3 Siren
2 AMP
Position
of Dialler
Board
Radio Transmitter/
Communicator Power
Connect to mains
Transformer
+Siren
123
456
789
0
*
#
P
M
O
D
E
FM
1
2
3
4
5
6
7
8
9
10
11
12
D+
D-
GND
+12V
P
A
N
I
C
P
A
N
I
C
PAN
LED
DOOR LED
3K3
NC +
-
P.I.R.
NC +
-
P.I.R.
3K3
MAG SW N/C
3K33K3
3K3
Connect as required with a
resistor in unused zones
B
L
A
C
K
W
IR
E
R
E
D
W
I
R
E
-
+
12V BATTERY
Radio Transmitter
or Communicator
Dialler Board
IDS1200 Connection Diagram

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 7
IDS1200 INSTALLER MANUAL
!If the zones are programmed to report tamper by zone, the 4K7 and 12K end-of-line resistors should be
connected as per Figure 2 below. The 4K7 and 12K resistors are not included with the panel but may
be obtained from your local distributor of IDS products.
Figure 2: Tamper per Zone Connection
P. I . R .
++
--
N/C
N/C
T
TGROUND
ZONE
12V
ALARM
PANEL
12K
4K7
!The operation of the tamper is as follows:
!If a partition is not armed and a tamper condition occurs, the siren will not sound but a tamper
condition will be reported.
!If a partition is armed and tamper condition occurs the alarm will register a zone violation and a
tamper condition will bereported.
!Regardless of whether the partition is armed or not, if a zone is programmed as a priority/panic
zone, a tamper will register a panic condition as well a tamper condition.
!The colour codes for the 12K and 4K7 resistors are as seen in Figure 3 below.
Figure 3: Resistors used for Tamper per Zone
Purple
Brown Orange
Red
12K 4K7
Yellow Red
4. Connecting the Telephone Communicator
Refer to Figure 1.
!The integral communicator has built in lightning protection to protect it from lightning induced
transients. For optimum protection connect a low impedance earth to the communicator. A poor earth
will be ineffective and may result in damage to the communicator and alarm panel.
!Always connect the telephone communicator in the line seizure mode. Never in parallel with the
telephone i.e. connect the telephone receiver to the communicator terminals marked “phone” and the
incoming line to the terminals marked “line”.

8 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
5. Programmable Outputs
A relay board must be used when any device requiring a high current (>50mA) is connected to a
programmable output. The current sink and source capability is the same for outputs 1-5. The output
circuitry consists of a 12 volt source with a 56Ωseries resistor. Current sink is via a 1000Ωresistor to
negative. The output circuitry for a single output is provided in Figure 4 below. All outputs are identical.
Figure 4: Programmable Output Configuration
6. The Key-Switch or Remote Control Unit
A momentary keyswitch or non-latching remote control receiver may be connected to any zone to allow
remote arm/disarm capability and/or remote panic.
!If a keyswitch or remote control unit is used, a 3K3 resistor must be connected between the zone input
and ground. (Use the 4K7 and 12K resistors if tamper per zone is enabled).
!Use a normally open, spring-loaded momentary keyswitch or a non-latching remote control unit. The
remote receiver must provide a pulsed output.
!If using a keyswitch, program the zone as an Arm/Disarm zone i.e. a value of [5] entered into the
relevant location.
!If using a remote control, program the zone as either a Panic zone or an Arm/Disarm zone, as required.
!The partition can be programmed to arm with or without an exit delay when arming by means of a
keyswitch or remote control unit.
7. Additional Technical Data
!Use a suitable transformer with an output voltage of 15 volts AC ±10% with a 32VA minimum rating. A
48 VA transformer is preferable for larger installations.
!Use a 12v sealed lead acid battery, min. 7ah. The back up period after mains failure will depend on the
number of keypads, sensors and peripheral devices attached to the system. The current drawn
by the panel and keypad (no indicators illuminated) excluding sensors is 240mA.

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 9
IDS1200 INSTALLER MANUAL
!The panic zone provided on the keypad is not an end-of-line supervised zone and requires a normally
open panic switch. If using this panic zone connect a normally open panic switch between the PAN
terminal and the GND terminal. If this zone is not used leave the terminal open circuit.
!A door LED may be connected to the keypad. This LED will mimic the ARM LED on the keypad i.e.
When the system is not armed the LED will be extinguished. If the system is armed the LED will be
illuminated and will flash if an alarm condition was registered while the system was armed. Note that
the anode of the LED connects to the LED terminal on the keypad and the cathode of the LED is
connected to the GND terminal. No series resistor is required.
!The current drawn by one keypad is 100mA, each PIR draws 20mA. Do not connect more than 30 PIR’s
and 4 keypads (to a total of 1A) to the auxiliary 12 volt outputs.
!The siren output requires a self driven 12 volt siren. The siren minus terminal is connected to ground.
The positive terminal of the siren is connected to 12 volts via a relay during the siren period.
!A full description of each programmable function of the panel is contained in the section titled
Program Location Summary.
!All information regarding the programming of user codes, home zones, delayed interior zones and
chime zones is contained in the User Manual.
!If a radio transmitter or voice message communicator is being used for monitoring purposes the power
for these devices should be taken from the “+TX” terminal.
8. Hardware Reset Switch
In the event that the installer code is lost, it is possible to reset the panel to its factory default values using
the hardware reset switch labelled SW1 on the main PC board. The panel may be defaulted by removing
both battery and AC power from the panel, and then reapplying the power (AC/battery) while depressing the
switch. Factory default values will be restored to all locations.
NOTE:
It is possible to disable the hardware reset switch (see location 1300) but not advisable. Should an installer
code be lost or forgotten when the hardware reset switch has been disabled, it is not possible to enter
programming mode or default the panel.
9. Event Log
The IDS1200 automatically keeps an internal log of all events which may be communicated through the
onboard communicator. 300 of the most recent events will be retained. Once the event log is “full” the oldest
event will be overwritten by the most recent event. An event is logged regardless of whether or not the panel
is programmed to communicate the event.
The event log can only be retrieved by means of the Windows based download/upload software and
appropriate modem.

10 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
10. Programming Instructions
10.1 Introduction
The panel may be programmed either using the keypad or using the up/download software. Programming
the panel by means of the keypad is explained in the following sections of this manual. For information on
programming the panel using the up/download software refer to the manual pertaining to the software.
NOTE:
Before commencing the programming it is advisable to read the Installer Manual thoroughly
10.2 Location Values
All values within a program location are displayed by the zone indicators in binary format. The table below
indicates how these values may be read.
Table 1: Value represented by each zone indicator
1enoZ 1
2enoZ 2
3enoZ 4
4enoZ 8
To read a binary value on the keypad add the values represented by each illuminated LED. The total value is
the number being represented e.g. Assume the following zone indicators are illuminated: Zone 1, Zone 3
and Zone 4. The value would be as shown in the table below.
1enoZ 1
3enoZ 4
4enoZ 8
latoT31
Table 2: Binary Representation
eulaV
0 1 2 3 4 5 6 7 8 9 01 11 21 31 41 51
2(1enoZ
0
)1=
"
#
"
#
"
#
"
#
"
#
"
#
"
#
"
#
2(2enoZ
1
)2+
""
##
""
##
""
##
""
##
2(3enoZ
2
)4=
""""
####
""""
####
2(4enoZ
3
)8=
""""""""
########
"
dehsiugnitxE
#
detanimullI
NOTE:
Any values greater than 15 use the zone LED’s 1-4 for the units digit; LED’s 7-10 for the tens digit. E.g.
assume the following zone indicators are illuminated: Zone 2, Zone 8 and Zone 9. The value would be as

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 11
IDS1200 INSTALLER MANUAL
shown in the table below.
2enoZ 28enoZ 2
9enoZ 4
:stinU2 :sneT6
latoT
26
10.3 Programming the Panel
!For all programming procedures, the [!!
!!
!](star) key functions as the enter key and the [#] (hash) key
functions as a clear key to clear incorrect or unintended entries, as a back space and to exit the
programming mode.
!If an error has been made i.e. an attempt is made to enter anillegal value or an incorrect series of
keystrokes, the keypad will beep three times to indicate the error. The panel will automatically
discard the invalid entry allowing the correct entry to be made without manually clearing the incorrect
entry.
Procedure
1. Ensure that neither partition is armed.
2. Press the [#] key (this will clear any previous or accidental entries) followed by the 4 digit [INSTALLER
CODE](the default code is 9999).
3. If the correct code has been entered the green READY indicator will begin flashing.
4. Press the [!!
!!
!]key.
5. Enter the [LOCATION NUMBER]of the program location that you wish to change.
6. Press the [!!
!!
!]key. The READY indicator will continue flashing.
7. The zone LED’s will now display the content of the selected program location in binary format (ref. Table
2).
8. If you wish to change the content of the location, enter the [NEW VALUE]followed by the [!!
!!
!]key. If you
do not wish to change the location value, press the [#] key. The READY indicator will continue flashing
and the AWAY indicator will start flashing.
9. If the data value has been changed, the buzzer will give a long beep indicating that a valid entry has
been stored.
10. Repeat steps 5-8 until all necessary locations have been programmed.
11. To exit from the programming mode press the [#] key.
The READY indicator will stop flashing to indicate that the program mode has been exited.

12 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
10.4 Program Location Summary
Following is a detailed description of the functioning of each location and its options.
0NOITACOL
edocresuretsamrolenapehtfognitluafeD
eulaV noitcA
0
tluafeD
ehtninmulocTLUAFEDehtninwohssaseulavtluafedyrotcafehtotsnoitacolllasteseR
lliwedocresuretsamehtdnadetluafedeboslalliwsedocresullA.tsilgnimmargorp
.4321emoceb
1 .sedocresuehtforedniamerehtgnitluafedtuohtiw4321otedocresuretsamehttluafedlliW
.deretla-nuniamerlliwnoitamrofnirehtollA
2 eht,desusiDItcatnoCnahtrehtotamrofrotacinummocafI.0otsedocgnitroperllateserlliW
0otsedocgnitroperllatluafedotelbasivdasitI.demmargorp-erebotdeensedocgnitroper
.sedocehtgnimmargorperotroirp
3 foredniamerehtgniraelctuohtiwsedocgnitroperssapybdnaesolc,nepoehtllaraelclliW
.sedocgnitropereht
4.sedocgnitroperlarotserenozehtfollaraelclliweulavsihtgniretnE
21-1SNOITACOL)21-1senoZ(scitsiretcarahCenoZ
Program locations 1 to 12 define the zone characteristics of each of the twelve zones. Each zone can be
programmed to function in one of eleven modes. Table 3 provides a location/zone cross-reference together
with the default zone characteristics.
Table 3: Location 1-12 / Zone Defaults
coL enoZ tluafeD epyTenoZ
111tixE/yrtnE
222rewolloF
334 tnatsnIelbiduA
444 tnatsnIelbiduA
554 tnatsnIelbiduA
664 tnatsnIelbiduA
774 tnatsnIelbiduA
884 tnatsnIelbiduA
994 tnatsnIelbiduA
01014 tnatsnIelbiduA
11114 tnatsnIelbiduA
21213 ytiroirPelbiduA
Table 4 overleaf provides a description of the different zone types that may be programmed into these
locations i.e. a value of 3 programmed into location 5 would cause zone 5 to be an audible priority zone.

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 13
IDS1200 INSTALLER MANUAL
Table 4: Programmable Zone Types
eulaV epyTenoZ
1TIXE/YRTNEYRAMIRP
nagnitaloiV.erudecorpgnimraehtfodoirepyaledtixeehtgnirudderongisienoztixE/yrtnEnafonoitaloiV
dnayrtneehtrof239dna139,22,12snoitacoleeS.yaledyrtneehtsetaitinidemranehwenoztixE/yrtnE
elbanelliwgnimraretfaenoztixE/yrtnEnahguorhttixeoteruliaF.2dna1snoititraprofsdoirepyaledtixe
noitidnocmralana,seripxedoirepyaledyrtneehterofebderetnetonsiedocresUdilavafI.edomyatseht
.31noitacolotnidemmargorpeulavehtybdetceffasiepytenozsihtforuoivahebehT.deretsigereblliw
2REWOLLOF
eehtgnirudderongieblliwenozrewolloFafonoitaloivA doirepyaledtixe/yrtn otresuehtswollasiht(
nadnademrasilenapehtfienoztnatsninasaevaheblliwenozrewolloFA.)enozrewollofehtaivtixe/retne
demmargorpseulavehtybdetceffasiepytenozsihtforuoivahebehT.tsrifdetaloivtonsienoztixE/yrtnE
.31noitacolotni
3CINAP/YTIROIRPELBIDUA
ehtesuaclliwenozytiroirPelbiduAnafonoitaloiva,tonrodemrasinoititrapehtrehtehwfosseldrageR
.nerisehtdnuosdnanoitidnocmralanaretsigerotlenaplortnoc
4TNATSNIELBIDUA
retsigeryletaidemmiotlenaplortnocehtesuaclliwenoztnatsninafonoitaloiveht,demrasinoititrapehtfI
.derongisienoztnatsnInafonoitaloiva,demranusinoititrapehtelihW.noitidnocmralana
5MRASID/MRA
atcennocytilicafsihtesuoT.mrasidromraotlenapehtesuaclliwenozmrasiD/mrAnafonoitaloivA
ebllitslliwrotsiserenil-fo-dneehT.enozsihtottinulortnocetomergnihctal-nonrohctiws-yekyratnemom
.deriuqer
6YTIROIRPTNELIS
ehtesuactonlliwenozytiroirPtneliSafonoitaloiv,tonrodemrasinoititrapehtrehtehwfosseldrageR
ehtotsnoitacolmargorptnavelerehtotnidemmargorpedocetairporppaehttroperlliwtubdnuosotneris
.noitatslartnec
7TNATSNITNELIS
yletaidemmiotlenaplortnocehtesuaclliwenoztnatsnItneliSafonoitaloivehtdemrasinoititrapehtfI
tneliSafonoitaloivehtdemranusilenapehtelihW.dnuostonlliwnerisehT.noitidnocmralanaretsiger
.derongisienoztnatsnI
8TIXE/YRTNEYRADNOCES
enozsihtnehwdesueblliw)2noititrap-339dna,1noititrap-32noitacolees(yaledyrtneyradnocesehT
tixE/yrtnEyramirParetfadetaloivsienoztixE/yrtnEyradnoceSafI.demrasilenapehtelihwdetaloivsi
.yaledyrtneyramirpehtnwod-tnuocoteunitnoclliwlenapehtdetaloivneebsahenoz
9YRTNE/REWOLLOF
.enozrewollofasastcatidemraerasnoititraphtobfI.snoititrapowtotnommocsienozyrtnE/rewolloFA
.enoztixe/yrtnenasastcatidemrasidsisnoititrapehtfoenofI
01 ENOZERIF
-ekoms,noitaloivtsrifehtfonoitcetednopU.cigolnoitacifireverifetaroprocnimetsysehtnosenozeriF
anitluserlliwdoirepetunim1anihtiwsnoitaloivtneuqesbuS.sdnoces02roftesereblliwrewoprotceted
lenapehtrehtehwfosseldragerdnuosotnerisehtesuaclliwnoitidnocerifA.deretsigergniebnoitidnocerif
.)ffodnoceseno,nodnoceseno(yltnettimretnidnuoslliwnerisehT.tonrodemrasi
:ETON
dilavagniretneybdecnelisebnacnerisehT
]EDOCRESU[ ehtnwodgnidloH. ]#[ dapyekehtlitnuyek
.rotcetedekomsehtteserlliwspeeb
11 REPMAT
ees(demrasilenapehtrehtehwfosseldragernoitatsesabehtotdetropereblliwenozsihtfonoitaloivA
.detavitcaeboslalliwnerisehtdemrasilenapehtfI.)sedocgnitroperenozehtrof774-454snoitacol

14 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
31NOITACOLsnoitpOgnimrAtnatsnI
eulaV noitcA
0
tluafeD
delbasiD
1delbanE
When this option is disabled an entry/ exit delay is allowed when arming and disarming. This means that
follower zones may be violated and the entry/ exit zone may be opened and closed during the entry and exit
delay times, provided that these zones are clear at the end of the arming time. See location 19 to program
whether arming can be initiated with the entry/ exit zone violated. When enabled, this option allows the
partition to arm or disarm as soon as a user code is entered. See location 1299 for keyswitch arming.
41NOITACOLsnoitpOgnimrAdessapyB
eulaV noitcA
0delbasiD
1
tluafeD
delbanE
Bypassed zones refer to zones that the panel will ignore during an armed cycle. See the User Manual for
how to bypass zones. If forced arming is enabled (see location 15) it is only necessary to bypass a zone if
it is clear at the time of arming but may be violated during the armed cycle.
51NOITACOLsnoitpOgnimrAdecroF
eulaV noitcA
0
tluafeD
delbasiD
1delbanE
Forced arming allows the partition to arm with violated zones e.g. an open window. Once the partition arms,
a violated zone will bypass automatically. If a zone which has been automatically bypassed clears while the
panel is armed, the zone will become active i.e. if the open window is pushed closed, reopening it will cause
an alarm condition to be registered.
61NOITACOLsnoitpOgnimrAkciuQ
eulaV noitcA
0delbasiD
1
tluafeD
delbanE
The quick arm option allows the user to arm the partition by holding down the [1] key until the keypad
beeps. Using the quick arm key initiates an arming cycle as if a valid user code has been entered. User
code 1 will be reported if the quick arm key is used.

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 15
IDS1200 INSTALLER MANUAL
71NOITACOLsnoitpOgnimrAyatS
eulaV noitcA
0
tluafeD
ehtesutonseoddnasmraresuehtfiedomyatsehtnimrayllacitamotualliwnoititrapehT
.evitcaeblliwsyekmrAkciuQehT.)enoztixe/yrtnenafonoitaloiv.e.i(enoztixe/yrtne
1 yatsehT.sruccoenoztixe/yrtnenafonoitaloivonfineveedomyawaehtnimralliwnoititrapehT
ehtnwodgnidloh(yekmrakciuqedom ]5[ .)delbasidoslasi
2 revewohsruccoenoztixe/yrtnenafonoitaloivonfineveedomyawaehtnimralliwnoititrapehT
.evitcasniameryekmrakciuqedomyatseht
The stay mode allows the user access to certain pre-programmed “stay” zones while the partition is armed.
Zones that are programmed as stay zones (See the User Manual) will automatically be bypassed when the
partition is armed into the stay mode. The [5] key will arm the partition in stay mode with no exit delay.
81NOITACOLsnoitpOsenoZnommoCfognissapyB
eulaV noitcA
0delbasiD
1
tluafeD
delbanE
The panel can be programmed to prevent or allow user bypassing of common zones.
NOTE:
If a zone belongs to both partitions, it will only be active when both partitions are armed.
91NOITACOLdetaloiVsenoZtixE/yrtnEhtiwgnimrA
eulaV noitcA
0
tluafeD
delbasiD
1delbanE
The panel can be programmed as to whether the entry/ exit zone must be clear or can be violated at the
time of arming (i.e. while entering a user code to arm.)
02NOITACOLgnitropeRlauD
eulaV noitcA
0
tluafeD
delbasiD
1delbanE
This location determines whether the panel will report events to one or two base stations.
If the panel is programmed to report to one base station (single reporting), it will dial both telephone
numbers alternately until it connects with a base station or the number of dial attempts is reached
(programmed into location 674).

16 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
If the panel is programmed to report to two different base stations (dual reporting), it will continue to dial
each of the numbers until it has transmitted the information to both (or the maximum number of dial
attempts is reached).
Also see location 33 - Tone/ Pulse Dialling Options.
12NOITACOL1noititraP-yaleDtixE
eulaV yaleD eulaV yaleD
0.ces3 8.nim2
1.ces01 9.nim3
2.ces51 01 .nim4
3.ces02 11 .nim5
4.ces52 21 .nim01
5)tluafeD(.ces03 31 .nim51
6.ces54 41 .nim81
7.nim1 51 .nim12
NB: See Location 931 for Partition 2 exit delay (Page 34).
This is the period of time allowed for exiting before partition 1 arms. The exit delay begins after entry of a
valid user code. During this period it is possible to violate entry/exit and follower zones without causing an
alarm condition. Select the appropriate exit delay period from the table on the previous page.
22NOITACOL1noititraP-yaleDyrtnEyramirP
eulaV yaleD eulaV yaleD
0.ces3 8.nim2
1.ces01 9.nim3
2.ces51 01 .nim4
3.ces02 11 .nim5
4.ces52 21 .nim01
5)tluafeD(.ces03 31 .nim51
6.ces54 41 .nim81
7.nim1 51 .nim12
NB: See Location 932 for Partition 2 primary entry delay (Page 34).
This is the period of time allowed to enter and disarm partition 1 before an alarm condition is registered. The
entry delay begins after the violation of a primary entry/exit zone. During this period it is permissible to
violate follower zones without causing an alarm condition provided that an entry/exit zone was violated first.
If a follower zone is violated without a prior entry/exit zone violation, it will be treated as an instant zone. If
an instant zone is violated during this period the alarm condition will immediately be registered. Select the
appropriate value for the primary entry delay from the table above.

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 17
IDS1200 INSTALLER MANUAL
32NOITACOL1noititraP-yaleDyrtnEyradnoceS
eulaV yaleD eulaV yaleD
0.ces3 8.nim2
1.ces01 9.nim3
2.ces51 01 .nim4
3.ces02 11 .nim5
4.ces52 21 .nim01
5)tluafeD(.ces03 31 .nim51
6.ces54 41 .nim81
7.nim1 51 .nim12
NB: See Location 933 for Partition 2 secondary entry delay (Page 35).
The secondary entry delay applies to the secondary entry/ exit zone. If a primary entry zone is violated, the
primary entry delay is activated. If a subsequent violation of a secondary entry/ exit zone occurs, the panel
will continue to count down the primary delay. If a valid user code is not entered during this period an alarm
condition will occur. Select the appropriate value for the Partition 1 Secondary Entry Delay from the table
above.
42NOITACOLdoirePtuOemiTneriS
eulaV yaleD eulaV yaleD
0.ces3 8)tluafeD(.nim2
1.ces01 9.nim3
2.ces51 01 .nim4
3.ces02 11 .nim5
4.ces52 21 .nim01
5.ces03 31 .nim51
6.ces54 41 .nim81
7.nim1 51 .nim12
The siren time out period is the period of time for which the siren will sound after an alarm condition is
registered. Select the appropriate time-out period from the table above.
52NOITACOLemiTerotseRdnaliaFCA
eulaV yaleD eulaV yaleD
0.ces3 8.nim2
1.ces01 9.nim3
2.ces51 01 )tluafeD(.nim4
3.ces02 11 .nim5
4.ces52 21 .nim01
5.ces03 31 .nim51
6.ces54 41 .nim81
7.nim1 51 .nim12

18 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
If the AC power should fail, the panel will wait for this period of time before reporting the mains failure to the
base station or logging the event to the event log. If the AC power is restored after the time out period has
ended the same time out period will apply before the restoral event is reported and logged.
If the AC power is restored during the delay period neither the power failure nor the power restoral will be
reported or logged to the event log. This delay eliminates unnecessary reporting if the AC power to the panel
is accidentally removed for a short period (provided the back up battery is in good condition, short AC power
failures will not affect the functioning of the alarm system).
Select the appropriate value from the table on the previous page.
62NOITACOLDIdapyeK
1tigiD 2tigiD
eulaV noitcA eulaV noitcA
0
delbasidnoititrapetanretlafognimrA
1
1noititrapotdengissadapyeK
1
dapyeKretsaM.e.idelbanenoititrapetanretlafognimrA
2
2noititrapotdengissadapyeK
NB: Before entering this information ensure that the number of partitions (location 857)
has been set up.
If a keypad is assigned to a partition that does not exist the panel will shut the keypad out and the keypad
ID will have to be defaulted by holding down the [1] and the [!!
!!
!]keys when the panel is powered up. The
keypad will then be defaulted to partition 1.
The keypad ID is a two digit number which is used by the keypad and must be entered individually at each
keypad. If the first digit is a “1” then the keypad is a master keypad that can alter the status of either
partition. If the first digit is a “0” then the keypad can only affect the partition to which it is assigned.
The second digit determines to which partition the keypad is assigned.
EXAMPLE:
To assign master status to a keypad in partition 2, enter [12] into location 26 of the appropriate keypad
(1=Master, 2=Partition 2).
To assign ordinary status to a keypad in partition 1, enter [01] into location 26 of the appropriate keypad
(0=Ordinary, 1=Partition 1).
72NOITACOLtuOemiTdapyeKretsaM
eulaV noitcA
0noititrapdetcelesnisyatS
)tluafeD(1 noititraplanigirootstreveR
This option affects how a master keypad is assigned to a specific partition. If the [MODE]key is held down
and a partition number pressed, the keypad will be assigned to the selected partition. If this option is
enabled (a value of [0] is programmed), the keypad will remain assigned to the selected partition, otherwise
the keypad will revert to its original partition 20 seconds after the last key is pressed.
92-82SNOITACOL devreseR

IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18 19
IDS1200 INSTALLER MANUAL
03NOITACOLsnoitpOyaleDnoitacinummoC
eulaV noitcA
)tluafeD(0 delbasiD
1delbanE
This option enables a delay before reporting an event. The delay time is programmed into location 31. If the
delay is enabled the following events will not be reported if a user code is entered during the delay:
!Zone violation
!Zone Tampering
!Panic Zone Violation
!Fire Zone Violation
!Tamper Zone Violation
The event will be logged when it occurs.
13NOITACOL)02=tluafeD(yaleDnoitacinummoC
If an event occurs that will be reported, the panel will wait for this period of time in seconds before
transmitting the relevant reporting codes, if this feature is enabled (location 30). If a valid user code is
entered during the delay period, the reporting codes will not be transmitted. The event will still be recorded in
the event log. The value of this location ranges from 0 to 250 seconds in 1 second increments. Program a
value from [0] to [251].
23NOITACOLtamroFrotacinummoC
eulaV noitcA noitpircseD
)tluafeD(0 tsafrepuSaoceS SHzHk3.2,XTzHk8.1
1sserpxEocmedAFMTD,SHenoTlauD
2)ytiraPoN(2x4IBF SPP02,SHzHk3.2,XTzHk8.1
3)ytiraP(2x4IBF SPP04,SHzHk3.2,XTzHk8.1
4wolS2x4thginKtneliS SPP01,SHzHk4.1,XTzHk9.1
5tsaF2x4thginKtneliS SPP02,SHzHk4.1,XTzHk9.1
6DItcatnoCFMTD,SHenotlauD
7gnitropeRcitsemoDSPP01,dnilB,XTzHk9.1
8tamroFregaPFMTD,dnilB
TX = Transmit
HS = Handshake
PPS = Pulses per Second
The value entered into location 32 selects the format to be used for communication to the base station
receiver or other device. Select from the table above the value appropriate to the required format. During
communication the green LED on the communicator PCB will illuminate. If programmed accordingly (see
location 1295), the keypad will beep once the panel has received a handshake from the base station. This
indicates a successful transmission of data.

20 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
NOTE ON DUAL REPORTING
If dual reporting is enabled both base stations will receive all programmed reporting codes.
NOTES ON CONTACT ID.
If the panel has been programmed to use the Contact ID reporting format (i.e. location 32=6) it is not
necessary to program the reporting codes. All codes will be reported by default. Table 5 contains a list of
standard (default) Contact ID reporting codes.
Under certain conditions it may be necessary to change or disable certain codes. If a particular reporting
code is not required, program a [0] (not “10”) into the relevant locations.
Any event that relates to a specific zone, or to a specific user, will have the relevant zone/user number
attached to the end of the Contact ID reporting code.
It is common not to report stay arming, away arming and disarming for domestic alarms. To disable the
reporting of these functions, program the following locations:
Arming or Closing code Locations 70 - 133 = 0
Disarming or Open code Locations 198 - 261 = 0
Clear Open, Close and Bypass codes Location 0 = 3
Clear Zone Restoral codes Location 0 = 4
Table 5: Standard Contact ID reporting codes
noitpircseD sedoC noitircseD sedoC
resuybesolC1043ssapyBenoZ0751
mraotuaybesolC3043nwodtuhSenoZ3751
daolnwodybesolC7043larotserenoZ0313
hctiws-yekhtiwesolC9043enozybrepmaT7311
resuybnepO1041repmaTdapyeK7311
daolnwodybnepO7041tuokcoldapyeK7311
hctiws-yekhtiwnepO9041enozcinaP0211
lecnaC6041cinaP0211
noitaloivyralgruB0311cinapdapyeK0211
noitaloivretemireP1311liafCA1031
noitaloivroiretnI2311larotserCA1033
noitaloiv)efaS(ruoH423311yrettabwoL2031
noitaloivtixe/yrtnE4311tropertseT2061
noitaloivthgin/yaD5311erifdapyeK0111
noitaloivroodtuO6311eriF0111
noitaloivrepmaT7311sseruD1211
noitaloivmralaraeN8311lacidemdapyeK0011
The generic Contact ID reporting code for an alarm caused by a zone violation is 1130, corresponding to a
“BURGLARY” description. If required particular zone violations may be reported with a description other than
BURGLARY an option may be chosen from Table 6 overleaf. The second digit of the reporting code relevant
to that zone must be changed to the value as indicated in the table.