Abus TVVR30004 User manual

Quick guide for Video Surveillance kit: TVVR30004 | TVVR30104 | TVVR30404 | TVVR30414
This quickstart guide describes the initial installation steps for your video surveillance kit.
More detailed information can be found in the accompanying user guide.
TVVR30004

20
English
Dear customers,
Thank you for purchasing this product.
This product complies with current domestic and European
regulations.
Conformity has been proven, and all related certications
are available from the manufacturer on request (ABUS
Security-Center GmbH & Co. KG, Linker Kreuthweg 5, 86444
Ang).
To maintain this status and to guarantee safe operation, it
is your obligation to observe these operating instructions!
Read the entire operating manual carefully before putting
the product into operation. Pay attention to all operating
and safety information! All company names and product
descriptions are trademarks of the corresponding owner. All
rights reserved.
If you have any questions, please contact your specialist
dealer.

21
English
Scope of delivery
Manual
TVVR30004
TVVR30104
• 4-channel recorder incl. HDD
• 1x day/night vision outdoor camera
• Universal power supply unit
• 1x20 m coaxial cable
• USB mouse
• Quick guide
• Manual
• CD
TVVR30404
• 4-channel recorder incl. HDD
• 4x day/night vision outdoor cameras
• Universal power supply unit
• 4x20 m coaxial cable
• USB mouse
• Quick guide
• Manual
• CD
TVVR30414
• 4-channel recorder incl. HDD
• 4x day/night vision outdoor dome cameras
• Universal power supply unit
• 4x20 m coaxial cable
• USB mouse
• Quick guide
• Manual
• CD
TVVR30004
• 4-channel recorder
• Power supply unit
• USB mouse
• Quick guide
• Manual
• CD

22
English
Warnings
Only store the recorder and camera
in the ambient conditions recom-
mended by the manufacturer.
Ensure that there is always
sucient ventilation.
Ensure an uninterrupted
power supply.
Keep the recorder and camera away
from strong magnetic elds.
Keep liquids away from the recorder.
Turn the recorder o before
connecting or removing
peripheral devices

23
English
Connections
Video - In
BNC input for analogue cameras
Video - OUT
BNC plug for video output to connect to a
monitor as an alternative to VGA output
USB
Connection for USB devices
12 V
12 V: 12 V DC power connection
LAN
RJ45 port for a
network connection

24
English
Hardware Installation
Remove the 4 screws on the
underside of the recorder.
Open the box carefully. Align the hard disk drive
with the base plate of the
recorder.
Please ensure that you begin with step
1
for the hardware installation of TVVR30004. The hardware installation for the video surveillance kits TVVR30104, TVVR30404 and TVVR30414
starts at step
8
, as the hard disk drive is pre-installed for these models.
Secure the hard disk drive
onto the underside of the
recorder with the accompa-
nying screws.
1 3 42

25
English
Connect the hard disk
drive to the motherboard
with the data cable (small
connector) and the power
cable (large connector).
Now place the box over the
base plate of the recorder.
Ensure that the box is placed
along the guide rails.
Then secure the box and
the base plate with the 4
screws.
Connect your cameras to
the recorder.
5 6 7 8

26
English
Tips for camera installation
Plug the recorder into the power supply.
The blue LED bar on top of the recorder
indicates that the device is on. You
can choose to turn o the light
on the LED bar via the menu.

27
English
Avoid backlight or direct sunlight
Do not place cameras directly behind glass,
as this can result in reections
The camera must not be
installed on unstable surfaces
Please be aware that notice of video surveillance
is required by law in public places

28
English
Soware Set-up
1 2 3
If you untick the box, then the setup
wizard will no longer run automati-
cally at the next start-up. Click Next.
Select a language and click Next. In the Admin Password eld, enter
12345. Conrm with Enter.

29
English
4 5 6
To change the password, tick the New
Admin Password box. Enter the new
password in the New Password and
Conrm elds. Make a note of the
password and keep it in a safe place.
Click Next.
Specify time zone, date and system
time. Continue by clicking Next.
Set the adapter speed tye ‚NIC type‘
manually. Default and recommended
setting is the automatic detection (Self
adaptive).

30
English
7 8 9
If your router does not assign the
address data automatically, then enter
the data manually as shown in the
following steps. The Screenshots shows
an example of devices to be connected
with corresponding IP addresses.
To assign the address data automati-
cally, tick the DHCP box. The addresses
are then assigned automatically by
the router (provided this function is
supported). In this case, proceed from
point 13 onwards.
The rst three positions of the IP
address must correspond to the de-
fault gateway value. The last position
species the device activated through
the default gateway (e.g. the recor-
der), and is dened individually for
each device. For example, enter xxx.
xxx.xxx.64 for recorder 64.
192.168.0.1
192.168.0.25192.168.0.20

31
English
10 11 12
The Subnet Mask is a network segment
where IP addresses with identical net-
work addresses are used. The standard
value here is usually 255.255.255.0.
Call up “Run” in the start menu.
Enter “cmd” in the new window,
then “ipcong” in the prompt
which follows. Enter the default
gateway value in the recorder
screen.
The DNS Server translates an Internet
address into an IP address. Enter the
default gateway value under Prefer-
red DNS Server.

32
English
13 14 15
Click Init, then conrm the successful
initialisation with OK. Exit the screen
by pressing OK, then go to the next
screen by pressing Next.
All hard drives which are to be used for
recording must be initialized before-
hand. To initialise the hard drives, tick
the corresponding drive.
Chose the channel which shall be
congured at Camera. Please note
that you still have to congure the
arming schadules in the recorder
menu. For further information please
read the user manual.

33
English
16 17 18
Please click in the checkbox Start Re-
cording to activate the record. Choose
between a durable record (Normal) or
a record with motion detection (Mo-
tion Detection). In the menu of the
recorder you can dene areas and
the sensivity of the motion detection.
For copying these settings to other
camera channels please click on
Copy. Click in the checkbox of the
camera channels you want to
transfer the settings to and click on
OK to activate these settings.
Click on OK to nish the initial set-up.