Inhep Digital Security IDS 800 User guide

2 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
Summary of Operation
mrasid/mrA ]#[ +]EDOCRESU[
mrAyawAkciuQ
nwoddloH ]1[ dnoces1rof
mrAyatSkciuQ
nwoddloH ]5[ dnoces1rof
oG&mrAyatSkciuQ
nwoddloH ]6[ dnoces1rof
lenaPybrewsnAdecroF ]8[
demrasidebtsummetsyS-
cinaP
nwoddloH ]P[ dnoces1rof
eriF
nwoddloH ]F[ dnoces1rof
ycnegremElacideM
nwoddloH ]M[ dnoces1rof
yromeMmralA
nwoddloH ]0[ dnoces1rof
eliforPyatSegnahC ]EDOM[ +]9[ +]REBMUNELIFORP[ +[((
(
((]
enozassapyB [((
(
((]+]REBMUNENOZ[
enozemihcmargorP
nwoddloH ]2[ [+dnoces1rof
]
REBMUNENOZ
+[((
(
((]
enozyatsmargorP
nwoddloH ]3[ [+dnoces1rof
]
REBMUNENOZ
+[((
(
((]
enozzzubmargorP
nwoddloH ]4[ [+dnoces1rof
]
REBMUNENOZ
+[((
(
((]
sutatSelbuorTweiV
nwoddloH ]7[
sseruD ]#[ +]EDOCSSERUD[
41egapeeS-ediuGgnimmargorProF

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 3
IDS800INSTALLERMANUAL
Contents
1. Introduction to the IDS800............................................5
1.1 Features...........................................................................5
2. Installation and Wiring ..................................................6
3. End-of-Line Resistors/Tamper per Zone ....................7
4. Connecting the Telephone Communicator ................8
5. Programmable Outputs.................................................8
6. Expansion Board ...........................................................9
7. The Key-Switch or Remote Control Unit ..................10
8. Additional Technical Data ...........................................10
9. Hardware Reset Switch ..............................................12
10. Event Log.....................................................................12
11. Dialler Progress Mode................................................13
12. Download Code ...........................................................13
13. Programming Instructions ..........................................14
13.1 Introduction ....................................................................14
13.2 Location Values..............................................................14
13.3 Programming the Panel .................................................15
13.4 Program Location Summary..........................................16
14. Trouble Conditions Summary.....................................52

4 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
Figures
Figure 1: Connection Diagram..............................................6
Figure 2: Tamper per Zone Connection ..............................7
Figure 3: Resistors user for Tamper per Zone ...................8
Figure 4: Programmable Output Configuration ..................9
Figure 5: Expansion Board Connection ..............................9
Figure 6: Strobe Output Sequence ...................................29
Figure 7: Fire Detect Output Sequence............................30
Tables
Table 1: Dialler Progress as shown by zone LED’s..........13
Table 2: Value represented by each zone indicator.........14
Table 3: Binary Representation..........................................15
Table 4: Location/ Zone Defaults........................................17
Table 5: Programmable Zone Types...................................18
Table 6: Output Options ......................................................28
Table 7: Location default values ........................................28
Table 8: Standard Contact ID reporting codes .................35
Table 9: Alarm reporting codes...........................................36
Table 10: Trouble Conditions .............................................52

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 5
IDS800INSTALLERMANUAL
1. Introduction to the IDS800
The IDS800 is a versatile, state of the art, microprocessor based, eight
zone alarm panel. Most features are optional and may be programmed
either directly through the keypad or via the telephone system, using
theIDS download softwareand appropriatemodem.There areeight
programmableburglaryzones, appropriatesiren,auxiliary power
outputs and 5 outputs which may be programmed to perform various
trigger/switchingfunctions.
For correct operation the IDS800 must be used in conjunction with the
specifiedtransformer/batterycombinationand appropriateperipheral
sensorsand signalling devices.
1.1 Features
Four wire keypad operation - up to a maximum of 4 keypads.
Eight,fullyprogrammable, end-of-line(3K3)supervised zones,
and 1 dedicated panic zone per keypad which is not end-of-line
supervised.
Optionaltamperreporting perzoneusing doubleend-of-line
resistors (12K and 4K7).
Fullyprogrammable digital telephonecommunicator which
supports most industry standard formats.
Fiveprogrammabletriggeroutputs.
Non volatile EEPROM memory retains all program and event log
data in the event of a total power failure.
Programmableloop response time forall zones (global).
Upand downloadableusing IDS windowsbasedsoftware.
Excellent protection against lightning (provided by specialised
“zap tracking” and transient suppressors).
Auto-arm - panel can be programmed to arm daily at a pre-
determinedtime.
Event log (200 events) date and time stamped.
Fax defeat allows download access to the panel with other
devices connected to the phone line.
Dualreportingprovides for duplicatedreportingto twoindependent
central base stations.
Programmablesilent or audiblepanic.
Uniquediallerprogress barallowingfor monitoringofdialler
status.

6 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
2. Installation and Wiring
Pleaserefer toFigure 1:Connection Diagramand familiariseyourself
with the following sections.
Figure 1: Connection Diagram - without tamper per zone
3
2
1
ZONE 8
ZONE 7
ZONE 6
ZONE 5
ZONE 4
ZONE 3
ZONE 2
ZONE 1
C
D
-
+
+
+
-
+
+TX
18V AC
AUXILLIARY
OUTPUTS
KEYPAD
12V
SIREN
CONNECT TO MAINS
TRANSFORMER
RADIO TRANSMITTER /
COMMUNICATOR POWER
PANIC
BUTTON
N/O
PANIC
BUTTON
N/O
NC
NC C C+
+
-
-
P.I.R.
P.I.R.
MAG SW N/C
CONNECT AS
REQUIRED WITH A
RESISTOR IN
UNUSED ZONES
B
L
A
C
K
W
IR
E
R
E
D
W
I
R
E
-
+
12V BATTERY
123
456
789
0
*#
P
M
O
D
E
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ZONE 7
ZONE 8
CK
DAT
GND
+12V PAN
LED
P
A
N
I
C
3K3
3K3
3K3
3
K
3
P
A
N
I
C
NOTE: NO END OF
LINE RESISTOR
DOOR LED
EARTH
EARTH
LINE
LINE
PHONE
SW1
HARDWARE
RESET
SWITCH
FU2 AUXILIARY
POWER FUSE
1 AMP
FU1 BATTERY
FUSE
4 AMP
Dialler Board
Position of
Dialler Board
RADIO
TRANSMITTER
OR
COMMUNICATOR
TELKOM
M
F

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 7
IDS800INSTALLERMANUAL
3. End-of-Line Resistors/Tamper per Zone
All zones are end-of-line supervised.Any unused zones must also
be terminated with the appropriate resistor.
The end of line resistor should be placed inside or as close to the
sensor as possible.
If the zones are not programmed to report tamper by zone i.e. a
[0] is programmed into location 11 then use the 3K3 end-of-line
resistor.
If the zones are programmed to report tamper by zone, the 4K7
and 12K end-of-line resistors should be connected as per Figure 2
below. The 4K7 and 12K resistors are not included with the panel
but may be obtained from your local distributor of IDS products.
Figure 2: Tamper per Zone Connection
The operation of the tamper is as follows:
If the panel is not armed and a tamper condition occurs, the
siren will not sound but a tamper condition will be reported.
If the panel is armed and tamper condition occurs the alarm
will register a zone violation and a tamper condition will be
reported.
Regardless of whether the panel is armed or not, if a zone is
programmed as a priority/panic zone, a tamper will register a
panic condition as well a tamper condition.
If the tamper per zone is enabled, it affects all zones and therefore
both end-of-line resistors must be connected in all zones. If the
tamper facility is not used on a zone then the 12K resistor must
be connected directly across the zone (i.e. between the zone

8 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
input and ground) and the 4K7 resistor is used as the normal end-
of-lineresistor.
The colour codes for the 12K and 4K7 resistors are as seen in
Figure3below.
Figure 3: Resistors used for Tamper per Zone
Purple
Brown Orange
Red
1
2K 4K7
Yellow Red
4. Connecting the Telephone Communicator
Referto Figure1.
The integral communicator has built in lightning protection to
protect it from lightning induced transients. For optimum
protection connect a low impedance earth to the communicator.A
poor earth will be ineffective and may result in damage to the
communicatorand alarmpanel.
Always connect the telephone communicator in the line seizure
mode. Never in parallel with the telephone i.e. connect the
telephonereceiverto thecommunicator terminalsmarked“phone”
and the incoming line to the terminals marked “line”.
5. Programmable Outputs
A relay board must be used when any device requiring a high current is
connected to a programmable output. The current sink and source
capability is the same for outputs 1, 2 and 3. The output circuitry
consists of a 12 volt source with a 56Ωseries resistor. Current sink is
via a 1000Ωresistor to negative. The output circuitry is provided in
Figure4overleaf.
There is also an expansion board attached to the keypad bus which
providesfor an additionaltwo programmableoutputs whichfunctionas
per outputs 1 - 3. See the connection diagram in Section 2 for further
details. See also Section 6: Expansion Board.

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 9
IDS800INSTALLERMANUAL
Figure 4: Programmable Output Configuration
6. Expansion Board
Attached to the keypad bus, in parallel with the keypad, is an optional
expansionboard whichallowsfor thefollowing:
Programmable outputs 4 and 5 which function as per the values
programmed into locations 22 - 40 and locations 159 - 166.
Designated keypad buzzer which will function as per the
description in the user manual.
ARM, READY and POWER LED’s which will function as per the
description in the user manual for keypad LEDs.
Figure 5: Expansion Board Connection
Keypad
123
456
789
0
*
#
P
M
O
D
E
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ZONE 7
ZONE 8
GND
CK
DAT
+12V
+
C
D
_
Keypad connection
on main board
+
GD
DT
CK
BZ
PR
RD
AM
P4
P5
GD
Keypad Buzzer
Power LED
Ready LED
Arm LED
Auxilliary
Outputs
Expansion
Board
FM
12V
56R
1000R
GND Output 2
56R
1000R
GND Output 1
56R
1000R
GND Output
3

10 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
7. The Key-Switch or Remote Control Unit
A momentary key-switch or non-latching remote control receiver may
be connected to any zone to allow remote arm/disarm capability and/
or remote panic.
If a key-switch or remote control unit is used, a 3K3 resistor must
be connected between the zone input and ground. (Use the 4K7
and 12K resistors if tamper per zone is enabled).
Use a normally open, spring-loaded momentary key-switch or a
non-latchingremote controlunit.The remotereceivermust provide
a pulsed output.
If using a key-switch, program the zone as anArm/Disarm zone
i.e. a value of [5] entered into the relevant location.
If using a remote control, program the zone as either a Paniczone
or anArm/Disarm zone, as required.
The panel will arm instantly (no entry/exit delay) when arming by
means of a key-switch or remote control unit.
The panel has an exit delay which can be enabled or disabled
with the key-switch or remote control (See location 12).
8. Additional Technical Data
Use a suitable transformer with an output voltage of 15 volts AC
±10% with a 16VAminimum rating. A32 VAtransformer is
preferableforlarger installations.
Use a 12v sealed lead acid battery, min. 3ah. The back up period
after mains failure will depend on the number of keypads, sensors
and peripheral devices attached to the system. The current drawn
by the panel and keypad (no indicators illuminated) excluding
sensors is 240mA.
Thepanic zone providedon the keypadis not anend-of-line

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 11
IDS800INSTALLERMANUAL
supervised zone and requires a normally open panic switch. If
using this panic zone connect a normally open panic switch
between the PAN terminal and the GND terminal. If this zone is
not used leave the terminal open circuit.
A door LED may be connected to the keypad. This LED will
mimic the ARM LED on the keypad i.e. When the system is not
armed the LED will be extinguished. If the system is armed the
LED will be illuminated and will flash if an alarm condition was
registered while the system was armed. Note that the anode of
the LED connects to the LED terminal on the keypad and the
cathode of the LED is connected to the GND terminal. No series
resistor is required.
Do not connect more than 8 PIR’s and two keypads, (or 6 PIR’s
and 3 keypads) to the auxiliary 12 volt outputs.
Thesiren output requiresa selfdriven 12 voltsiren. Thesiren
minus terminal is connected to ground. The positive terminal of
the siren is connected to 12 volts via a relay during the siren
period.
A full description of each programmable function of the panel is
contained in the section headed Program Location Summary.
Allinformation regardingtheprogramming ofuser codes,home
zones delayed interior zones and chime zones is contained in the
UserManual.
If a radio transmitter or voice message communicator is being
usedfor monitoringpurposesthe powerfor thesedevices should
betaken from the“+TX” terminal.
NOTE:
The TX+ terminal is protected by means of the battery fuse. If
excessive current (2 amps max) is drawn from this terminal,
battery power to the alarm may be lost.

12 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
9. Hardware Reset Switch
In the event that the installer code is lost, it is possible to reset the
panel to its factory default values using the hardware reset switch
labelled SW1 on the main PC board. Provided that the reset switch
has not been disabled (see location 21) the panel may be defaulted by
removing both battery and AC powerfrom thepanel, andthen
reapplying the power (AC/battery) while depressing the switch. Factory
default values will be restored to all locations.
NOTE:
Once the reset switch has been disabled it is not possible to default
the panel using the reset switch. The panel may only be defaulted if a
valid installer code is used and a value of [0] is entered into location 0.
10. Event Log
The IDS800 automatically keeps an internal log of all events which
may be communicated through the onboard communicator. 200 of the
most recent events will be retained. Once the event log is “full” the
oldest event will be overwritten by the most recent event.An event is
logged regardless of whether or not the panel is programmed to
communicatethe event.
The event log can only be retrieved by means of the Windows based
download/uploadsoftwareandappropriatemodem.
The time of each event is not logged in absolute terms i.e. time of day
and date but relative to the previous event. The date and time indicated
on an uploaded event log is calculated by the PC using the PC clock
time. Since the time at which the upload event was initiated is known,
all other times can be calculated relative to this event.
The IDS800 does not contain an onboard battery to maintain the clock
time in the event of a total power failure (AC mains failure and
discharged battery) therefore in the event of a total power failure it will
not be possible to calculate the absolute time at which an event took
place. The relative time of each event will still be indicated.

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 13
IDS800INSTALLERMANUAL
11. Dialler Progress Mode
When the panel sends data to a central station, the keypad zone
LED’s may be used to display the “progress” of such communication.
To view the communication status proceed as follows:
1. Hold down the [0] key until the keypad buzzer sounds twice.
2. Press the [9] key. The ARMED, READY and AWAY LED’s will
flash simultaneously indicating that the Dialler Progress Mode
has been selected. Using the zone indicators the following table
will provide the communication status.
3. To exit this mode press the [#] key.
Table 1: Dialler Progress as shown by zone LED’s
eno
Z
DE
L
ybdnatS gnizeiS eniL gnillaiD esaB noitatS rofgnitiaW nO-ssiK gnidneS ataD rofgnitiaW ffO-ssiK
r
ofgnitiaW
l
aidtxen tpmetta
1enoZ
)))))))
2enoZ
)))))
3enoZ
))))
4enoZ
)))
5enoZ
))
6enoZ
)
7enoZ
)

dehsiugnitxE
) detanimullI
12. Download Code
A download code is used for download access. The default download
code is 9999. Via the downloading it is possible to set a location to
either allow or disallow defaulting of the download code. The location is
only accessible using the download software. If selected to allow
defaultingof the download code, the download codewill be defaultedto
9999 if the panel is defaulted.Avalue of [10] programmed into this
locationpreventsthe downloadcodefrom beingdefaulted.
This function may only be used with download software version 1.4.0
orlater.

14 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
13. Programming Instructions
13.1 Introduction
The panel may be programmed either using the keypad or using the
up/downloadsoftware. Programmingthepanel bymeans ofthe
keypad is explained in the following sections of this manual. For
informationonprogramming thepanelusing the up/downloadsoftware
refer to the manual pertaining to the software.
NOTE:
Before commencing the programming it is advisable to read the
InstallerManualthoroughly
13.2 Location Values
All values within a program location are displayed by the zone
indicators in binary format. The table below indicates how these values
may be read.
Table 2: Value represented by each zone indicator
1enoZ 1
2enoZ 2
3enoZ 4
4enoZ 8
To read a binary value on the keypad add the values represented by
each illuminated LED. The total value is the number being represented
e.g.Assume the following zone indicators are illuminated: Zone 1,
Zone 3 and Zone 4. The value would be as shown in the table below.
1enoZ 1
3enoZ 4
4enoZ 8
latoT31

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 15
IDS800INSTALLERMANUAL
Table 3: Binary Representation
eulaV
0 1 2 3 4 5 6 7 8 9 01 11 21 31 41
5
1
2(1enoZ
0
)1=

)

)

)

)

)

)

)

)
2(2enoZ
1
)2+

))

))

))

))
2(3enoZ
2
)4=

))))

))))
2(4enoZ
3
)8=

))))))))

dehsiugnitxE
)
detanimullI
13.3 Programming the Panel
For all programming procedures, the [(](star) key functions as
the enter key and the [#] (hash) key functions as a clear key to
clear incorrect or unintended entries, as a back space and to exit
theprogrammingmode.
If an error has been made i.e. an attempt is made to enter an
illegal value or an incorrect series of keystrokes, the keypad will
beep three times to indicate the error. The panel will automatically
discard the invalid entry allowing the correct entry to be made
without manually clearing the incorrect entry.
Procedure
1. Ensure that the panel is not armed.
2. Press the [#] key (this will clear any previous or accidental
entries)followedby the4 digit [INSTALLER CODE](thedefault
code is 9999).
3. If the correct code has been entered the green READY indicator
willbegin flashing.
4. Press the [(]key.
5. Enterthe[LOCATION NUMBER]oftheprogram locationthatyou
wish to change.
6. Press the [(]key. The READY indicator will continue flashing and
the AWAY indicator will illuminate.
7. The zone LED’s will now display the content of the selected
programlocation in binaryformat (ref.Table 3).
8. If you wish to change the content of the location, enter the [NEW
VALUE]followed by the [(]key. If you do not wish to change the

16 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
location value, press the [#] key. The READY indicator will
continue flashing and the AWAY indicator will extinguish.
9. If the data value has been changed, the buzzer will give a long
beep indicating that a valid entry has been stored.
10. Repeat steps 5-8 until all necessary locations have been
programmed.
11. To exit from the programming mode press the [#] key.
The READY indicator will stop flashing to indicate that the program
mode has been exited.
13.4 Program Location Summary
Following is a detailed description of the functioning of each location
and its options.
0NOITACO
L
edocresuretsamrolenapehtfognitluafeD
eulaV noitcA
0tluafeD ehtninwohssaseulavtluafedyrotcafehtotsnoitacolllasteseR oslalliwsedocresullA.tsilgnimmargorpehtninmulocTLUAFED .4321emoceblliwedocresuretsamehtdnadetluafedeb
1ehtgnitluafedtuohtiw4321otedocresuretsamehttluafedlliW -nuniamerlliwnoitamrofnirehtollA.sedocresuehtforedniamer .deretla
2rehtotamrofrotacinummocafI.0otsedocgnitroperllateserlliW -erebotdeensedocgnitropereht,desusiDItcatnoCnaht
r
oirp0otsedocgnitroperllatluafedotelbasivdasitI.demmargorp .sedocehtgnimmargorperot

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 17
IDS800INSTALLERMANUAL
8-1SNOITACO
L
)8-1senoZ(scitsiretcarahCenoZ
Program locations 1 to 8 define the zone characteristics of each of the
eight zones. Each zone can be programmed to function in one of
elevenmodes.Table 4providesa location/zonecross-reference
together with the default zone characteristics.
Table 4: Location/Zone Defaults
coL enoZ tluafeD epyTenoZ
111 tixE/yrtnE
222 rewolloF
334 tnatsnIelbiduA
444 tnatsnIelbiduA
554 tnatsnIelbiduA
664 tnatsnIelbiduA
774 tnatsnIelbiduA
883 ytiroirPelbiduA
Table 5overleaf providesa descriptionof thedifferentzonetypes that
may be programmed into these locations i.e. a value of 3 programmed
into location 5 would cause zone 5 to be an audible priority zone.

18 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
Table 5: Programmable Zone Types
eulaV epyTenoZ
0DELBASID derongisienozdelbasidafonoitaloiV.delbasideblliwenoZehT .dapyekehtnodetacidnitonsidna
1TIXE/YRTNE yaledtixeehtgnirudderongisienoztixE/yrtnEnafonoitaloiV nehwenoztixE/yrtnEnagnitaloiV.erudecorpgnimraehtfodoirep otnidemmargorpyaledyrtneehT.yaledyrtneehtsetaitinidemra eblliw81noitacolotnidemmargorpyaledtixeehtdna02noitacol lliwgnimraretfaenoztixE/yrtnEnahguorhttixeoteruliaF.desu
e
hterofebderetnetonsiedocresUdilavafI.edomyatsehtelbane .deretsigereblliwnoitidnocmralana,seripxedoirepyaledyrtne sidoirepyaledtixeehtgnirudepytenozsihtforuoivahebehT .9noitacolotnidemmargorpeulavehtybdetceffa
2REWOLLOF eehtgnirudderongieblliwenozrewolloFafonoitaloivA tixe/yrtn
doirepyaled rewollofehtaivtixe/retneotresuehtswollasiht(
si
lenapehtfienoztnatsninasaevaheblliwenozrewolloFA.)enoz foruoivahebehT.tsrifdetaloivtonsienoztixE/yrtnEnadnademra .9noitacolotnidemmargorpeulavehtybdetceffasiepytenozsiht
3CINAP/YTIROIRPELBIDUA nafonoitaloiva,tonrodemrasilenapehtrehtehwfosseldrageR naretsigerotlenaplortnocehtesuaclliwenozytiroirPelbiduA .nerisehtdnuosdnanoitidnocmrala
4TNATSNIELBIDUA ehtesuaclliwenoztnatsninafonoitaloiveht,demrasilenapehtfI ehT.noitidnocmralanaretsigeryletaidemmiotlenaplortnoc otnidemmargorpeulavehtnopudnepedlliwnerisehtforuoivaheb tnatsnInafonoitaloiva,demranusilenapehtelihW.51noitacol .derongisienoz
5MRASID/MRA romraotlenapehtesuaclliwenozmrasiD/mrAnafonoitaloivA -nonrohctiws-yekyratnemomatcennocytilicafsihtesuoT.mrasid
ll
iwrotsiserenil-fo-dneehT.enozsihtottinulortnocetomergnihctal .deriuqerebllits
6YTIROIRPTNELIS afonoitaloiv,tonrodemrasilenapehtrehtehwfosseldrageR troperlliwtubdnuosotnerisehtesuactonlliwenozytiroirPtneliS margorptnavelerehtotnidemmargorpedocetairporppaeht .noitatslartnecehtotsnoitacol

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 19
IDS800INSTALLERMANUAL
eulaV epyTenoZ
7TNATSNITNELIS esuaclliwenoztnatsnItneliSafonoitaloivehtdemrasilenapehtfI ehT.noitidnocmralanaretsigeryletaidemmiotlenaplortnoceht afonoitaloivehtdemranusilenapehtelihW.dnuostonlliwneris sienozsihT.derongisienoztnatsnItneliStonehtybdetceffa
.51noitacolotnidemmargorpeulav
8TIXE/YRTNEYRADNOCES sihtnehwdesueblliw)01noitacolees(yaledyrtneyradnocesehT ehtgniretnenehW.demrasilenapehtelihwdetaloivsienoz aretfadetaloivsienoztixE/yrtnEyradnoceSafidna,sesimerp
o
teunitnoclliwlenapehtdetaloivneebsahenoztixE/yrtnEyramirP .yaledyrtneyramirpehtnwod-tnuoc
01 ENOZERIF fosseldragerdnuosotnerisehtesuaclliwenozeriFafonoitaloiV
yl
tnettimretnidnuoslliwnerisehT.tonrodemrasilenapehtrehtehw tuptuoelbammargorpA.)ffodnoceseno,nodnoceseno( oslalliw)73noitacol(tuptuorewoprotcetederifasademmargorp detavitcaeb
21 MRAOTHSUP sahyaledtixeehtecno;51si81noitacolnieulavehtfI yletaidemmilliwenozmraothsupehtfonoitaloiva,decnemmoc lenapehtmra

20 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45
IDS800INSTALLERMANUAL
9NOITACO
L
snoitpOtixE/yrtnE
eulaV senoztixe/yrtnE raelcebtsum senozrewolloF raelcebtsum yaledtixe/yrtnE delbane
0
mrAtnatsnI raelcebtsumsenozllA
1
2
3
4
5
6
7
8

>
9tluafeD
>

>
01

>>
11
>>>
21

>
31
>

>
41

>>
51
>>>
>
delbanE

delbasiD
If the Entry/ exit delay is enabled, the panel can be programmed to
allow arming with violated Follower and/ or Entry/ exit zones.
NOTE:
For all values programmed into location 9 the panel will only arm if the
READY indicator is illuminated.