InkJetBiz XPress 1620SA User manual

XPress 1620SA SWING AWAY
User Manual
www.inkjetbiz.com
[e-mail]
[phone]

CON TEN T
In the Box
Product Features
Display setting
Operation Instruction
Transfer Parameters
Troubleshooting
03
04
05/06
07/08
09
10
NOTICE
1. Use the heat transfer press only as intend
2. Please keep children away from the machine
3. Use correct power outlet before plugging in the device
4. Burns can occur from contact with hot surface
5. Please hold the handle firmly when machine is opening
6. Turn off the device when not in use and remove the
power plug

XPress 1620 SA Swing Away(Single Platen)
In the box
1 x XPress 1620 SA 1 x Power Cable
1 x Silicon Mat 1 x User Manual
0304
1. Control Display
2. Heating Plate Cover
3. Silicone Mat
4. Alu. Lower Plate
5. Handle Bar
6. Power Switch
7. Foot Base
8. Machine Base
9. Power Outlet
10. Pressure Knob
11. Swing Arm
MACHINE INTRODUCTION
5
3
1
2
8
7
4
6
11
9
10

0506
Present Value
:Set Value :
Celsius Read-out:Fahrenheit Read-out:
Timing in Seconds:Temperature Digits:
Heating Indicator:Timing:
Plus Digits:Decrease Digits :
Set Mode:Counter Clearance :
(Long hold for temperature calibration)
(Long Hold)
CONTROL SETTINGCONTROLLER PROGRAM
Control Panel Display P-1 : Temp. Setting Mode
Touch SET & ↑ ↓ buttons to set desired Temp.
P-2 : Time Setting Mode
Touch SET & ↑ ↓ buttons to set desired time.
P-3 : ℃or ℉Read-out
Touch SET & ↑ ↓ buttons to set ℃or ℉
P-3 : ℃or ℉Read-out
Touch SET & ↑ ↓ buttons to set ℃or ℉
P-4 : Auto Power-o Mode
Touch SET & ↑ ↓ buttons to set auto-o time
with 0-120 mins range
Clear Counter NO.
You can long hold the CLEAR button
to clear the COUNTER NO. on the panel.
Auto-o Introduction
It reads OFF and machine starts to cool down after
machine raises to SET temp. and remains no
operation for P-4 set time. Operation like control
panel setting or heat pressing.
Wake Machine from Sleepy Mode
You can wake up the heat press from sleepy
mode by touching any button on the control
panel, and machine starts to heat again.

07 08
User Operation User Operation
A
Set recommended TEMP,TIME.
See Page 9 for
recommendations.
B
Adjust the pressure knob and
set the right pressure for your
application.
C
D
When ready, place your items on the
lower platen.
Recommend to preheat garment and
cover with teflon or parchment paper.
E
To press, hold the platen grip and
press down.
F
Peel off/remove the transfer paper.
See paper recommendations for
cold or hot peel.
G
Repeat steps E through G as needed
per your preferred transfer paper
recommendations.
H
Wait for heat pressto heat up to
the set temperature.
Pickup the Socket and connect to power
outlet then power-on the heat press.
Regardless ofthe regular T-shirts orthin
products, XPress 1620SA™Series are also
recommended forfluffy items like 4cm thick
while soft down-coats, sweaters, etc. While it’s
noso recommended for hard/solid & thick items
like 2cm MDF boards or ceramictiles, ofcourse
thinner product like 1cm iswell supported.
Control panel P-4 is auto power-off setting with
range 0-120min, 0 refers to not going enter into
sleepy mode. As long as machine reaches to the
set Temp. and is kept no in use for set time Say.
60mins, machine will enter into sleepy, display
shows OFF and temperature cools down.You
could touch any button on the control panel to
wake up the machine.
For any further help, please contact
our support team.
[email protected]
[phone]

09 10
Transfer Parameters Troubleshooting
Remarks
Transfer Material
Sublimation paper
Light color inkjet
& laser transfer
paper
200 °C
185 °C
165 °C
25 ~ 35 s
15 s
8~15 s
Light color polyester fabric
Time
Heavy
Base Material
Remarks
Non woven fabric bags
Light color cotton fabric
Light color polyester fabric
Non woven fabric bags
Light color cotton fabric
Dark color inkjet
& laser transfer
paper
Dark color polyester fabric
PU leather
Dark color cotton fabric
Polyester fabric
Knit fabrics
Cotton fabric
Printer Temperature TimeDevice Pressure Remarks
Heat transfer
Vinyl (HTV)
Micro
piezoelectric
inkjet Epson &
Ricoh printers
with CISS
& sublimation ink
Xpress 1620SA
Heat Press
Inkjet printer with
pigment ink &
inkjet paper.
Laser printer with
laser paper.
Cutting plotters
15~25 s
Medium
150~160°C
10~15 s
Check beforehand
if your HTV
requires
hot or cold peel
Teflon sheet is
required
Mirror your design
when printing on
sublimation
paper
Q:When pressed onto the garments, the color of the design is faded, or transfers are not fully stacked onto the garments.
A: Reason comes from three points, the pressure is no enough, the temperature is not hot enough or the design has not been pressed for
enough time. You may need to try more to get right temp, time and pressure.
Q:The transfers are stacked on the heating platen.
A: Transfers like dark ink-jet transfer paper could be stacked on heating platen, you should use a Teflon sheet to cover the transfer paper.
If this happen, please turn-off and cools machine completely before you try to peel the stacked paper, do not use sharp item like knife to
scrape the heating platen as Teflon maybe scratched.
Q: Hard to peel off the transfer paper or vinyl.
A: Please make sure transfers are warm peel or cold peel, so as to peel off accordingly.
Q: LCD control panel shows “000”.
A: That refers the thermocouple wire is disconnected, you shall turn to support team for help and replace the disconnected connection.
Q: How to get a reasonable pressure.
A: Adjust the pressure know and try to lock down the handle, feel there is certain large resist force.
Q: Turn on the power, but the heat press does not work.
A: Pls check the power plug connected well to the socket, you may turn to support team if problem is still remaining.
Any further help, please contact our support team.
Xpress 1620SA
Heat Press