InkJetBiz XPress 1620SA SWING AWAY with Caddie User manual

XPress 1620SA SWING AWAY
with Caddie
User Manual
www.inkjetbiz.com
[e-mail]
(408)394 -7595

NOTICE
CON TEN T
In the Box
Product Features
Display Settings
Operation Instruction
Transfer Parameters
Troubleshooting
03
04
05/06
07/08
09
10
1. Use the heat transfer press only as intend
2. Please keep children away from the machine
3. Use correct power outlet before plugging in the device
4. Burns can occur from contact with hot surface
5. Please hold the handle firmly when machine is opening
6. Turn off the device when not in use and remove the
power plug

XPress 1620SA Swing Away with Caddie (110v)
In theboxes
1 x XPress 1620 SA 1 x Power Cable
1 x Caddie * 1 x User Manual
0304
MACHINE INTRODUCTION
1. Control Display
2. Heating Plate Cover
3. Silicone Mat
4. Lower Plate
5. Handle Bar
6. Power Switch
7. Pressure Knob
8. Power Outlet
9. Swing Arm
10. Caddie locking wheel
11. Sliding Setup Knob
12. Height Adjustment Knob
5
3
10
1
2
11
12
4
9
8
7
* Please note assembly is required
6

0506
Present Value
:Set Value :
Celsius Read-out:Fahrenheit Read-out:
Timing in Seconds:Temperature Digits:
Heating Indicator:Timing:
Plus Digits:Decrease Digits :
Set Mode:Counter Clearance :
(Long hold for temperature calibration)
(Long Hold)
CONTROL SETTINGCONTROLLER PROGRAM
Control Panel Display P-1 : Temp. Setting Mode
Touch SET & ↑ ↓ buttons to set desired Temp.
P-2 : Time Setting Mode
Touch SET & ↑ ↓ buttons to set desired time.
P-3 : ℃or ℉Read-out
Touch SET & ↑ ↓ buttons to set ℃or ℉
P-3 : ℃or ℉Read-out
Touch SET & ↑ ↓ buttons to set ℃or ℉
P-4 : Auto Power-o Mode
Touch SET & ↑ ↓ buttons to set auto-o time
with 0-120 mins range
Clear Counter NO.
You can long hold the CLEAR button
to clear the COUNTER NO. on the panel.
Auto-o Introduction
It reads OFF and machine starts to cool down after
machine raises to SET temp. and remains no
operation for P-4 set time. Operation like control
panel setting or heat pressing.
Wake Machine from Sleepy Mode
You can wake up the heat press from sleepy
mode by touching any button on the control
panel, and machine starts to heat again.

07 08
User Operation User Operation
A
Set recommended TEMP,TIME.
See Page 9 for
recommendations.
B
Adjust the pressure knob and
set the right pressure for your
application.
C
D
When ready, place your items on the
lower platen.
Recommend to preheat garment and
cover with teflon or parchment paper.
E
To press, hold the platen grip and
press down.
Regardless ofthe regular T-shirts orthin
products, XPress 1620SA™Series are also
recommended forfluffy items like 4cm thick
while soft down-coats, sweaters, etc. While it’s
noso recommended for hard/solid & thick items
like 2cm MDF boards or ceramictiles, ofcourse
thinner product like 1cm iswell supported.
F
Peel off/remove the transfer paper.
See paper recommendations for
cold or hot peel.
G
Repeat steps E through G as needed
per your preferred transfer paper
recommendations.
H
Wait for heat pressto heat up to
the set temperature.
Pickup the Socket and connect to power
outlet then power-on the heat press.
Control panel P-4 is auto power-off setting with
range 0-120min, 0 refers to not going enter into
sleepy mode. As long as machine reaches to the
set Temp. and is kept no in use for set time Say.
60mins, machine will enter into sleepy, display
shows OFF and temperature cools down.You
could touch any button on the control panel to
wake up the machine.
After ten thousands ofswing-away and press,
maybe you need to adjust theposition screw on
theback column tomake sure theupper heating
platen andlower platen isalways paralleled.
For any further help, please contact
our support team.
[email protected]
[phone]

09 10
Transfer Parameters Troubleshooting
Transfer Material
SubiMate Paper 392 °F
285 °F
35 s
Time
Medium
Low to
Base Material
Remarks
Polyester
100% Poly
60% Poly - 40% Cotton
*Color may fade with lower
polyester percentages
Light color polyester fabric
Non woven fabric bags
Light color cotton fabric
Dark/Colored Polyester
Dark/Colored Cotton
Print Head Temperature TimeDevice Pressure Remarks
TFP - DX
•Xpress
1620SA
•XPress
1620SA
Caddie
30 - 35 s
Mirror your
design when
printing.
Q:When pressed onto the garments, the color of the design is faded, or transfers are not fully stacked onto the garments.
A: Reason comes from three points, the pressure is no enough, the temperature is not hot enough or the design has not been pressed for
enough time. You may need to try more to get right temp, time and pressure.
Q:The transfer paper is stuck on the heating platen.
A: You should use a Teflon sheet or parchment paper to cover the transfer paper prior to pressing.
Q: Hard to peel off the transfer paper or vinyl.
A: Please make sure transfers are warm peel or cold peel, so as to peel off accordingly.
Q: LCD control panel shows “000”.
A: That refers the thermocouple wire is disconnected, you shall turn to support team for help and replace the disconnected connection.
Q: How to get a reasonable pressure.
A: Adjust the pressure know and try to lock down the handle, feel there is certain large resist force.
Q: Turn on the power, but the heat press does not work.
A: Pls check the power plug connected well to the socket, you may turn to support team if problem is still remaining.
Shock Line Top Cut Toner
•
•
Xpress
1620SA
XPress
1620SA
Caddie
347 °FMedium
to High
Shock Line Top Dark Toner
•
•
Xpress
1620SA
XPress
1620SA
Caddie
Medium
to High
30 - 35 s
LeatherMate
Cotton
255 °FMedium
to High
60 s
Use a Layer of
Polyester on top,
prior to pressing,
for protection.
Fuze Fabric
Leather •
•
Xpress
1620SA
XPress
1620SA
Caddie
Toner
TFP - DX 35 - 40 s
385 °F
Medium
Low to
Mirror your
design when
printing.
Mirror your
design when
printing.
Use a
Layer of
Polyester on top,
prior to pressing,
for protection.