INNOSILICON T3+57T User manual

T3+ BTC
USER MANUAL

Catalogue
1. Overview........................................................................................................... 0
2. Assemble the miner.......................................................................................... 1
2.1 Open the package to check the miner................................................................................... 1
2.2 Assemble & Operate............................................................................................................. 2
3. Operate the miner............................................................................................ 3
3.1 Enter the miner console ........................................................................................................ 3
3.2 Configure the pool ................................................................................................................ 4
3.3 View the miner hash rate ...................................................................................................... 5
3.4 Network configuration.......................................................................................................... 6
3.5 Other pages ........................................................................................................................... 6
3.5.1 Change the operation mode ............................................................................................... 6
3.5.2 Overview............................................................................................................................ 7
3.5.3 Firmware upgrade.............................................................................................................. 7
3.5.4 Modify the login password ................................................................................................ 8
3.5.5 Reboot................................................................................................................................ 8
3.5.6 Factory reset....................................................................................................................... 8

1. Overview
Specifications
Part Number
T3+
Algorithm
Sha256
Hash Rate
57TH/S (+/-5%)
Size (L×W×H)
305mm(L)*203mm(W)*278mm(H)
Net Weight
10.38KG
Operating Temperature
0--40 ℃(device junction temperature)
Network Connection
Ethernet

1
Innosilicon After-sales Team
Email: [e-mail]
2. Assemble the miner
2.1 Open the package to check the miner
⚫Check whether the warranty sticker is damaged, especially the one on hash boards
PSU port side.If the warranty sticker is damaged when you receive the miner, please
contact our after-sales personnel in time.
⚫Before assembling the miner, pls shake the miner gently. Please contact our after-
sales personnel immediately if there is metallic collision sound.
⚫Check whether the two fans work well, if you find the fans broken please contact our
after-sales personnel.
⚫The wiring of the miner shall not be changed including the power cable and data
cable interface as shown in the figure below.
Notes:
There is an indicator on each hash board which shows the work status of the hash board.
Being constantly lit means the hash board works properly.
Flickering represents overtemperature of the hash board. Please check the fans of the miner,

2
Innosilicon After-sales Team
Email: [e-mail]
environment temperature and the ventilation conditions.
Being off means the hash board doesn’t work. Please try to reboot the miner or change the
data cable. Pls contact our after-sales team if the problem still exists.
2.2 Assemble & Operate
Connect the miner and the router by the Ethernet cable and then the miner can start to run after being
powered on.
Notes: T3+ miners consume much more power under some modes. Pls choose proper sockets.
Normal Indicator：Being constantly lit represents static IP and flickering represents DHCP
Fault Indicator：Being on means there is something wrong with the network; Being off means it is OK.
IP SET button:
Press it for 1 to 4 seconds and the following functions can be realized:
(1) Sending the IP miner to the “Set IP” tool;
(2) Changing the miner to a Static IP within the specific range with the IPset tool
16A AC Cable port
Switch
Ethernet port

3
Innosilicon After-sales Team
Email: [e-mail]
Press it for 4 to 15 seconds, the miner IP will be switched to DHCP and the pool settings will be restored
to default settings.
Press it for 15 to 30 seconds to switch the Dynamic (Static) IP to Static (Dynamic).
RESET button: Press the “Reset” button to restart the miner.
3. Operate the miner
3.1 Enter the miner console
DHCP is the default IP mode of the miner (The normal indicator of the control board now is flickering in
green when the DHCP service of the router is enabled.). Find the IP via the IP scanner or the SetIP tool
developed by our company. Pls refer to the official support center for the downloading address
https://www.innosilicon.com/html/support_en/tool.html.
a) Save SetIP in the pc on the same network with the miner, then double click the tool and choose
the language.

4
Innosilicon After-sales Team
Email: [e-mail]
b) Report the miner IP
Enter the IP of the miner in the browser and press the Enter button to go to the miner console page.
Chrome is the suggested browser. (Please try with dragonadmin if the password admin is invalid.)
3.2 Configure the pool
Pls configure the pool to start mining after login.
Please use the suggested pool as below:
1 f2pool：stratum+tcp://btc-65536.f2pool.com:3333
2 poolin: stratum+tcp://btc-bj.ss.poolin.com:1800 or stratum+tcp://btc-sz.ss.poolin.com:1800
Press the IPset button 1 to 2 seconds then
the IP of the miner will show here

5
Innosilicon After-sales Team
Email: [e-mail]
3 ckpool：stratum+tcp://cn.ckpool.org:443 or stratum+tcp://pool.ckpool.org:3333
4 btc.top：stratum+tcp://t2.btc.top:8888 or stratum+tcp://bak.t2.btc.top:3333
5 slushpool：stratum+tcp://stratum.slushpool.com:3333
3.3 View the miner hash rate
After configuring the pool, the miner will mine for you. You can view the hash rate in the Miner Status
screen.
Pls add “stratum+tcp” before the pool URL

6
Innosilicon After-sales Team
Email: [e-mail]
3.4 Network configuration
3.5 Other pages
3.5.1 Change the operation mode
There are 4 modes available and please click the “Save” icon after your modification.

7
Innosilicon After-sales Team
Email: [e-mail]
3.5.2 Overview
3.5.3 Firmware upgrade

8
Innosilicon After-sales Team
Email: [e-mail]
3.5.4 Modify the login password
3.5.5 Reboot
3.5.6 Factory reset
1
1