Inovonics EE1265 EchoStream User manual

5.25.17 05377D © Inovonics, 2017 - www.inovonics.com
EE1265 EchoStream® 360° Passive InfraRed
Motion Detector
Installation and Operation Manual
1 Overview
The EE1265 is a wireless, ceiling-mounted, four-element passive infrared
(PIR) intrusion detector providing protection from intruders by pyro-sensor
array. Micro-controller signal analysis with special technology for pulse
processing increases immunity to interference, vibration, static, lightning,
ambient temperature changes, and other common causes of false alarms.
Caution: The EE1265 needs one minute for stabilization after power up.
During the stabilization period, the LED will blink twice per second, and the
EE1265 will not be operational.
1.1 Inovonics Contact Information
If you have any problems with this procedure, contact Inovonics technical
services:
• E-mail: [email protected].
• Phone: [phone].
1.2 EE1265 Internal Components
Figure 1 EE1265 internal components
1.3 What’s in the Carton
• Four drywall mounting anchors.
• Four mounting screws.
• Two selection jumper.
• Two 3.0V lithium batteries.
2 Installation and Startup
2.1 Installation Notes
• These products are designed to be maintained by professional
security technicians.
• Products are tested for indoor use.
• All products should be manually tested weekly.
2.2 Install the Batteries
The EE1265 can accommodate two batteries for extra battery life, but only
one is required for operation.
Note: When installing batteries, it is recommended that batteries are
replaced in new pairs from the same manufacturer.
To install batteries:
1. Loosen the housing tamper lock screw.
Figure 2 Remove the housing cover and mounting bracket
2. Install the battery included with the unit.
3. Install an optional second battery.
4. Press the Reset button to initialize the transmitter.
Note: You must press the Reset button each time a new battery is
installed.
2.3 Enable EchoStream Select
To meet ETSI requirements, Inovonics has developed a new line of EE
868MHz-only products. These new 868MHz-only products are compatible
with older systems that include EchoStream Select products. If you are not
using any ES products in your current system, skip to 2.4, “Select PIR
Sensitivity”; if you are using ES products in your current system, you will
need to configure the transmitter.
To enable EchoStream Select compatibility:
5. To enable compatibility with ES products, place a selection jumper on
the ES selection pins.
Note: The selection jumper is included in the EE1265 hardware packet.
6. Press the Reset button to initialize the transmitter.
Caution: When pressing the Reset button, make sure you don’t also touch
the ES selection pins. Touching the ES selection pins while pressing the
Reset button can inadvertently set the EE1265 to the wrong frequency
band.
2.4 Select PIR Sensitivity
The pulse count selection pins provide control for difficult operating
environments. Automatic pulse count is recommended for reliable
operation in environments subject to temperature fluctuation that can cause
false alarms. The single pulse count mode is more sensitive to minor
temperature variations, and should be used in sites where variant heat
sources will not cause alarms. Automatic pulse count is the factory default
because it allows more reliable operation in environments subject to
temperature fluctuation. If you are using automatic pulse count, skip to 2.5,
“Select Fixed/Variable Sleep Time”; if you are using single pulse count
mode, you will need to configure the transmitter.
To select PIR sensitivity:
7. Place the jumper on the left two pins to select a single pulse count.
For product and installation videos visit us at
www.inovonics.com/videos or use the QR
code below.
ABatteries BTamper switch CPulse count selection pins
DTest LED EReset button FTest button
GES selection
pins
HTest reed switch IFixed/variable sleep time
selection pins
A
I
H
B
DF
G
E
C
Housing
tamper lock
screw
Remove
the
housing
cover
Remove
the
mounting
bracket

5.25.17 05377D © Inovonics, 2017 - www.inovonics.com 2
2.5 Select Fixed/Variable Sleep Time
The sleep time jumper setting provides control for normal or high-traffic
operating environments. When set to fixed, if the EE1265 senses motion, it
will transmit an alarm, then enter sleep mode for 180 seconds; if motion is
sensed when the sleep time has expired, the EE1265 will transmit another
alarm. Fixed sleep time is recommended for normal operating
environments. When set to variable, if the EE1265 senses motion, it will
transmit an alarm, then enter sleep mode for 180 seconds; if motion is
sensed before the sleep time has expired, the EE1265 will restart the 180
second interval. Variable sleep time is recommended for high-traffic
operating environments.
8. Place a selection jumper on the appropriate sleep countselection pins.
• Place the jumper on the left two pins to select variable sleep time.
• Place the jumper on the right two pins to select fixed sleep time.
9. Install the battery.
10. Press the Reset button.
2.6 Register the PIR
The EE1265 must be registered.
11. Refer to receiver, network coordinator, or control panel installation
instructions to register the EE1265. Press Reset when prompted to
register the transmitter.
Caution: The EE1265 should be tested after registration to ensure
operation. To test the EE1265, activate each of the conditions and ensure
an appropriate response.
2.7 Mount the EE1265
12. Install the housing cover and housing tamper lock screw.
Note: Ensure the housing tamper lock screw is tightened sufficiently to
depress the tamper switch. If the housing tamper lock screw is not
sufficiently tightened, the EN1265 will remain in a state of tamper.
13. Remove the mounting bracket.
14. Use the provided anchors and screws to mount the EE1265 housing
base to the ceiling.
• The EE1265 can be mounted to a maximum height of approximately
12 feet (3.6 meters). As mounting height increases, distance between
detection zones also increases toward the perimeter, and the effects
of factors such as floor surface temperature and intruder direction and
speed are intensified. This can contribute to reducing the speed of
detection. Every installation should include a walk test of detection
zones, including intrusion paths crossing the edges of the zones. See
Figure 3 and Figure 4 for more information.
Figure 3 EE1265 detection diameter
Note: The ACC689 long range lens allows for an install height of up to 25
feet.
Figure 4 EE1265 lens pattern
15. When the housing base has been attached to the ceiling, install the PIR
on the mounting bracket.
3 Test the EE1265
3.1 Walk Test
When in walk test mode the test LED will light every time the EE1265
senses motion. The unit will not transmit alarm signals during this test
period. There are two ways to initiate a walk test. Once initiated, the walk
test will last for one minute. To initiate a walk test:
1. With the cover off the unit, pass a magnet near the walk test reed switch
for one second, or press the test button for one second.
Note: The test LED only lights during the walk test and the transmission
test.
3.2 Transmission Test
When in transmission test mode the unit will transmit alarm and restoral
cycles at regular intervals for approximately one minute. The LED will light
every time the unit transmits. To initiate a transmission test:
1. With the cover off the unit, hold a magnet near the walk test reed switch
for at least three seconds, or press the test button for at least three
seconds.
4 Operation
The EE1265 contains a tamper switch on the board to alert the user if the
housing cover is removed. The EE1265 also contains tamper contacts in
the mounting bracket to alert the user if the unit is removed from the wall.
5 Specifications
Dimensions: 131mm x 57mm (5.2" x 2.25").
Weight: 185g (6.52 oz.).
Detection method: 4-element PIR.
Operating temperature: 0°C to 49°C (32°F to 120°F).
Humidity: 10% to 90% non-condensing.
Battery: Inovonics BAT604 (3.0V lithium Duracell DL123A) .
Note: Battery is supervised.
Typical battery life: 2 years in location with low to moderate activity.
Visible light protection: Stable against halogen light 8 feet (2.4m) or
reflected light.
Temperature compensation: Yes.
Pulse count: Selectable single pulse or multiple pulse.
Operating frequency: 868-869 MHz.
Output power: 25mW.
Firmware revision: 90484, v3.01.
Ceiling - 3 m (10 ft)
Effective Detection Diameter
14 m (46 ft)
0.8 M (2.6 Ft)
Floor

5.25.17 05377D © Inovonics, 2017 - www.inovonics.com 3
Countries in which Inovonics European products can be distributed:
Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Greece, Hungary, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, United Kingdom.
Note: Specifications and data are subject to change without notice.
Note: Changes or modifications to this unit not expressly approved by
Inovonics may void the installer's authority to operate the equipment as
well as the product warranty.
6 Simplified Declaration of Conformity
Hereby, Inovonics declares that the radio equipment type EE1265 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
Internet address: www.inovonics.com
7 US Patent Numbers
• 7,154,866.
• 7,554,932.
• 7,746,804.
• Other patents pending.