INOXPA KIBER KSF Manual

INSTALLATION, SERVICE AND
MAINTENANCE INSTRUCTIONS
PROGRESSIVE CAVITY PUMP
KIBER KSF for wine
INOXPA, S.A.
c/ Telers, 54 Aptdo. 174
E-17820 Banyoles
Girona (Spain)
Tel. : (34) 972 - 57 52 00
Fax. : (34) 972 - 57 55 02
email: [e-mail]
www.inoxpa.com
Original Manual
01.611.30.00EN
(E) 2016/02

EC Declaration of Conformity
The manufacturer: INOXPA, S.A.
c/ Telers, 57
17820 Banyoles (Girona), Spain
herewith declares that the machine:
KIBER KSF for wine Progressive Cavity pump
with the serial number: ________________
conforms to the relevant provisions of the following directives:
Machinery Directive 2006/42/EC (RD 1644/2008)
Low voltage Directive 2006/95/EC
Electromagnetic Compatibility Directive 2004/108/EC
Applicable harmonised Standards:
UNE-EN ISO 12100:2012
UNE-EN 809:1999+A1:2010
Identification of the person empowered to draw up the Declaration on behalf of the manufacturer, and qualified to
compile the technical file established by the Community:
Banyoles, 3 February 2016
David Reyero Brunet
Technical Office Manager

2016/02 1.Safety 3
1. Safety
1.1. INSTRUCTION MANUAL
This manual contains information regarding the reception, installation, operation, assembly, disassembly and maintenance of
the pump Kiber KSF for wine.
The information published in the instruction manual is based on updated data.
INOXPA reserves the right to modify this instruction manual without prior notice.
1.2. INSTRUCTIONS FOR START-UP
This instruction manual contains essential and useful information for the correct handling and maintenance of your pump.
Carefully read the instructions prior to starting the pump, familiarise yourself with the installation, operation and correct use of
the pump and strictly follow the instructions. These instructions must be kept in a safe location near the installation area.
1.3. SAFETY
1.3.1. Warning symbols
Danger for people in general
Danger of injury caused by rotating
equipment parts
Electric hazard
Danger! Caustic or corrosive agents
Danger! Suspended loads
Danger for the correct operation of the
equipment
Mandatory to ensure safety at the
workplace
Mandatory use of safety goggles
1.4. GENERAL SAFETY INSTRUCTIONS
Read the instruction manual carefully before installing and starting the pump. Contact INOXPA in
case of doubt.
1.4.1. During the installation
The Technical Specifications in Section 8 should always be observed.
Never start the pump before connecting it to the lines.
Check for proper specifications of the motor, especially if its working conditions create an explosion
hazard.
During the installation, all the electric work should be carried out by authorised personnel.
1.4.2. During operation
The Technical Specifications in Section 8 should always be observed. Under no circumstances can the
specified limit values be exceeded.
NEVER touch the pump or the pipework during operation if the pump is being used for transferring
hot liquids or during cleaning.

4 1.Safety 2016/02
The pump contains moving parts. Never place your fingers inside the pump during operation.
NEVER operate with the suction and discharge valves closed.
NEVER spray water directly on the electrical motor. The standard protection of the motor is
IP55: Protection against dust and water spray.
1.4.3. During maintenance
The Technical Specifications in Section 8 should always be observed.
NEVER disassemble the pump until the pipes have been emptied. Bear in mind that the pumped
liquid may be hazardous or extremely hot. Consult the regulations in effect in each country for these
cases.
Do not leave loose parts on the floor.
ALWAYS disconnect the electrical power to the pump prior to carrying out any maintenance. Remove
the fuses and disconnect the cables from the motor’s terminals.
All electrical work must be carried out by authorised personnel.
1.4.4. Compliance with the instructions
Any failure to comply with the instructions may impose a risk for the operators, the environment and the machine, and may
ultimately result in the loss of the right to claim damages.
This non-compliance may result in the following risks:
Failure of important machine/plant functions.
Failure of specific maintenance and repair procedures.
Possible electrical, mechanical and chemical hazards.
Risk to the environment due to the type of substances released.
1.4.5. Warranty
Any warranty will be void immediately and lawfully; additionally, INOXPA will be compensated for any civil liability claims
submitted by third parties, in the following cases:
The service and maintenance work have not been carried out in accordance with the service instructions, the repairs
have not been carried out by our personnel or have been carried out without our written authorisation;
Modifications have been carried out on our material or equipment without written authorisation;
The parts or lubricants used are not INOXPA genuine parts;
The material or equipment has been improperly used, has been used negligently, or has not been used according to
the instructions and their intended;
The pump parts are damaged because they have been subjected to high pressure due to not having used a safety
valve.
The General Terms of Delivery already in your possession are also applicable.
The machine may not undergo any modification without prior approval from the manufacturer. For
your safety, only use original spare parts and accessories.
The usage of other parts will relieve the manufacturer of any liability.
Changing the service conditions can only be carried out with prior written authorisation from
INOXPA
Please do not hesitate to contact us in case of doubts or if further explanations are required regarding specific data
(adjustments, assembly, disassembly, etc.).

2016/02 2.Table of contents 5
2. Table of contents
1. Safety 3
1.1. Instruction manual ........................................................................................................ 3
1.2. Instructions for start-up................................................................................................. 3
1.3. Safety .......................................................................................................................... 3
1.4. General safety instructions ............................................................................................. 3
2. Table of contents 5
3. General Information 6
3.1. Description ................................................................................................................... 6
3.2. Field of application ........................................................................................................ 6
4. Installation 7
4.1. Reception of the pump .................................................................................................. 7
4.2. Handling and storage .................................................................................................... 7
4.3. Location ....................................................................................................................... 8
4.4. Pipes............................................................................................................................ 8
4.5. Shut-off valves.............................................................................................................. 8
4.6. Electrical installation ...................................................................................................... 8
5. Start-up 9
5.1. Start-up ....................................................................................................................... 9
5.2. Pressure by-pass........................................................................................................... 9
6. Operating problems 10
7. Maintenance 11
7.1. General considerations................................................................................................. 11
7.2. Storage ...................................................................................................................... 11
7.3. Cleaning..................................................................................................................... 12
7.4. Disassembly / Assembly of the pump ............................................................................ 12
8. Technical Specifications 15
8.1. Technical Specifications ............................................................................................... 15
8.2. Weights...................................................................................................................... 15
8.3. Dimensions KIBER KSF FOR WINE pump with trolley ...................................................... 16
8.4. Dimensions KIBER KSF FOR WINE pump with by-pass.................................................... 16
8.5. Exploded view of KIBER KSF FOR WINE pump ............................................................... 17
8.6. Parts list KIBER KSF FOR WINE pump ........................................................................... 18

6 3.General Information 2016/02
3. General Information
3.1. DESCRIPTION
With a compact and robust design, INOXPA's Kiber KSF progressive cavity pumps for wine form part of our range of positive
displacement pumps intended for the wine industry.
The pump is made up of two hydraulic parts, the rotor and the stator. The rotor is a round-section worm screw. The stator has
two ribs and its pitch doubles that of the rotor, which provides empty cavities between the stator and the rotor which are used
to move the fluid along. The turning motion of the rotor inside the stator makes the cavities move longitudinally from the
suction area to the discharge nozzle.
This type of pumps are suitable for pressures of up to 6 bar.
All the parts of the pump in contact with the product being pumped are made of stainless steel AISI 316L. The stator is made
of PERBUNAN with a specific hardness for this application.
The most significant details of the design of this type of pump are as follows:
Pump mounted on trolley with pneumatic wheels, depending on the model.
Pump housing with drain port.
Eccentric discharge port.
Pump with mirror polished surface finish.
Mechanical disk-type adjustable speed drive
Control panel with start/stop, contactor and emergency stop.
Pressure bypass (optional).
Liquid detection sensor (optional).
Gear motor with built-in frequency inverter (optional).
This unit is approved for use with food products.
3.2. FIELD OF APPLICATION
The field of application for each type of pump is limited. Each pump is ordered to meet specific
pumping conditions. INOXPA shall not be liable for any damage that may occur if the information
provided by the buyer is incomplete (specifications of the fluid to be pumped, RPM, etc.).

2016/02 4.Installation 7
4. Installation
4.1. RECEPTION OF THE PUMP
INOXPA will not be liable for any deterioration of the material occurred during shipping or
unpacking. Visually check that the packaging has not been damaged.
The following documentation is included with the pump:
Shipping documents
Instructions and Servicing manual for the pump.
Instructions and Servicing manual for the motor (*).
(*) If the pump has been supplied with a motor from INOXPA.
Unpack the pump and check the following:
The suction and discharge connections on the pump, removing any
remaining packaging material.
Check that the pump and motor have not suffered any damage.
If the material is not in good condition and/or if any part is
missing, the shipping carrier should submit a report as soon as
possible.
4.1.1. Identification of the pump
Pump plate
4.2. HANDLING AND STORAGE
The Kiber KSF pumps are too heavy to be handled and stored manually.
Lift the pump as indicated below:
Always use two support points placed as far apart as
possible.
Secure the points in a manner that prevents them
from sliding or moving.
Serial number

8 4.Installation 2016/02
4.3. LOCATION
Place the pump as close as possible to the suction tank; if possible, below the fluid level.
Place the pump in a position that allows enough space around it to provide access to the pump as well as to the motor. (Refer
to Section 8 . Technical Specifications for dimensions and weights).
Place the pump on a flat and level surface.
Install the pump so as to allow proper ventilation.
If the pump is installed outdoors, it must be sheltered under a roof. Its location must allow for easy
access during any inspection or maintenance tasks.
4.4. PIPES
As a general rule, install the suction and discharge lines in straight sections, with the minimum possible number of bends and
fittings in order to reduce as much as possible any pressure losses that may be caused by friction.
Make sure that the pump’s ports are properly aligned with the pipework and have a diameter similar to that of the pump
connections.
Place the pump as close as possible to the suction tank, if possible below the fluid level, or even below the tank, in order to
achieve the largest possible static head for suction.
Place pipe supports as close as possible to the pump's suction and discharge ports.
4.5. SHUT-OFF VALVES
The pump may be isolated for maintenance. To accomplish this, shut-off valves must be installed and connected to the pump's
suction and discharge connections.
These valves must ALWAYS be open during operation of the pump.
4.6. ELECTRICAL INSTALLATION
The connection of the electrical motors must be performed by qualified personnel.
Take the necessary precautions to prevent damage to cables and connections.
Electrical equipment, terminals and components of the control systems may still bear electrical
current when they are disconnected. Contact with them may be dangerous for operators or cause
irreversible damage to equipment.
Prior to handling the pump, make sure that the electrical panel is disconnected.
Connect the motor in accordance with the instructions supplied by the motor manufacturer.
Check for proper direction of rotation (see the label located on the pump).
Start the pump motor briefly. Make sure the pumping direction is the right one. Running the pump in the wrong direction
may cause serious damage.
ALWAYS check the direction of rotation of the motor with liquid inside the pump.
The circuit diagrams of the electric panel are supplied separately from this manual.

2016/02 5.Start-up 9
5. Start-up
Prior to starting the pump, carefully read the instructions in Section 4. Installation .
5.1. START-UP
Carefully read Section 8. Technical specifications . INOXPA cannot be held responsible for the improper
use of the equipment.
NEVER touch the pump or the pipes if hot liquids are being pumped.
5.1.1. Checks before starting up the pump
Fully open the shut-off valves on the suction and discharge lines.
If liquid does not flow into the pump, fill it with the liquid to be pumped.
The pump must NEVER rotate without a fluid inside it.
Check that the direction of rotation of the motor is correct.
Check that the electrical power supply matches the rating indicated on the motor plate.
5.1.2. Checks when starting up the pump
Check that the pump is not making any strange noises.
Check if the absolute inlet pressure is sufficient to prevent cavitation in the pump. Check the curve to determine the minimum
pressure required above the vapour pressure (NPSHr).
Control the discharge pressure.
Check that there are no leaks through the sealed areas.
A shut-off valve shall not be used to regulate the flow in the suction line. All shut-off valves must be
fully open during operation.
Control the motor consumption to prevent an electrical overload.
5.2. PRESSURE BY-PASS
If the pump is fitted with a pressure by-pass, the pump can only rotate in one direction. To invert the direction of rotation,
mount a relief valve as indicated the next figure. The relief valve is set at 6 bar ex works (4 bar for the KSF-80 model).
The pump always leaves INOXPA with the by-pass installed so as to operate with suction in the
pump casing and discharge ahead..

10 6.Operating problems 2016/02
6. Operating problems
The following table provides solutions to problems that may arise while operating the pump. It is assumed that the pump has
been properly installed and that is has been selected correctly for the specific application.
Please contact INOXPA if technical assistance is required.
Operating problems
Probable causes
Motor overload
8, 9
The pump flow or pressure is insufficient.
1, 2, 4, 5, 7, 9, 10, 16, 17, 18.
There is no pressure on the discharge side.
2, 3, 6, 17, 17.
Uneven discharge flow rate / pressure.
1, 2, 4, 5, 6, 9, 19.
Noise and vibrations.
2, 4, 5, 6, 7, 8, 9, 10, 13, 14, 18.
The pump gets clogged.
9, 10, 14.
Pump overheated.
8, 9, 10, 14
Abnormal wear.
4, 5, 10, 14, 18.
The mechanical seal leaks.
11, 12, 15.
Probable causes
Solutions
1
Wrong direction of rotation
Reverse the direction of rotation
2
Insufficient NPSH
Increase the available NPSH:
- Raise the suction tank.
- Lower the pump.
- Reduce the vapour pressure.
- Increase the diameter of the suction pipe.
- Shorten and simplify the suction line.
3
Pump not purged
Purge or fill
4
Cavitation
Increase the suction pressure.(see also 2)
5
The pump sucks in air
Check the suction line and all of its connections
6
Suction pipe obstructed
Check the suction line and the filters, if available
7
Discharge pressure too high
If necessary, reduce the pressure losses, for example, by
increasing the pipe diameter.
8
Flow rate too high
Decrease speed
9
Viscosity of the liquid too high
Reduce the viscosity, for example, by heating the liquid
10
Liquid temperature is too high
Decrease the temperature by cooling the liquid
11
Mechanical seal worn or damaged
Replace the seal
12
Inadequate O-rings for the liquid
Install the correct O-rings after consulting the supplier
13
Stressed pipes.
Connect the pipes to the pump without tension
14
Foreign matter in the liquid
Install a filter in the suction pipe
15
Mechanical seal spring tension is too low
Adjust as indicated in this manual
16
Pump speed too low
Increase speed
17
Pump too small
Choose a larger pump size
18
The stator is worn out or has operated without a fluid
Replace the stator
19
Flow reduction
- Replace the stator
- Increase speed
If the problems persist, stop using the pump immediately. Contact the pump manufacturer or his
representative.

2016/02 7.Maintenance 11
7. Maintenance
7.1. GENERAL CONSIDERATIONS
This pump, just like any other machine, requires maintenance. The instructions in this manual cover the identification and
replacement of spare parts. The instructions are aimed at maintenance personnel and those responsible for the supply of spare
parts.
Carefully read Section 8. Technical specifications .
All replaced material should be duly disposed of/recycled according to the directives in effect in each
area.
ALWAYS disconnect the pump before beginning any maintenance work.
7.1.1. Check the mechanical seal
Periodically check that there are no leaks around the shaft. If leakage is detected through the mechanical seal, replace it
following the instructions in the section Assembly and Disassembly.
7.2. STORAGE
Before storing the pump it should be completely drained. Prevent as far as possible exposing the parts to excessively humid
environments.
7.3. CLEANING
The use of aggressive cleaning products such as caustic soda and nitric acid may burn the skin.
Wear rubber gloves during all cleaning procedures.
Always wear protective goggles.
7.3.1. CIP (Clean-in-Place) cleaning
If the pump is installed in a system with a CIP process, its removal will not be required.
If an automatic cleaning process is not available, disassemble the pump as indicated in the section Assembly and Disassembly .
Cleaning solutions for CIP processes.
Only use clear water (chlorine-free) to mix with the cleaning agents:
a) Alkaline solution: 1% by weight of caustic soda (NaOH) at 70ºC (150ºF)
1 kg NaOH + 100 litres of water = cleaning solution
or
2.2 litres of 33% NaOH + 100 litres of water = cleaning solution
b) Acid solution: 0.5% by weight of nitric acid (HNO3) at 70ºC (150ºF)
0.7 litres of 53% HNO3+ 100 litres of water = cleaning solution
Check the concentration of the cleaning solutions; incorrect concentrations may lead to the
deterioration of the pump seals.
To remove any remains of cleaning products, ALWAYS perform a final rinse with clean water upon completion of the cleaning
process.

12 7.Maintenance 2016/02
7.3.2. Automatic SIP (Sterilization-in-Place)
Sterilization with steam is applied to all equipment including the pump.
Do NOT start the equipment during the sterilization with steam.
The parts/materials will not be damaged if the indications specified in this manual are observed.
No cold liquid can enter the equipment until the temperature of the pump is lower than 60°C
(140°F).
The pump generates an important load loss through the sterilization process, we recommend using a
bypass circuit that uses a discharge valve to ensure the overheated steam / water sterilizes the
entire circuit.
Maximum conditions during the SIP process with steam or overheated water
a) Max. temperature: 140°C / 284°F
b) Max. time: 30 min
c) Cooling: Sterile air or inert gas
d) Materials: EPDM / PTFE (recommended)
FPM / NBR / (not recommended)
7.4. DISASSEMBLY / ASSEMBLY OF THE PUMP
7.4.1. Stator, rotor and connecting rod
Disassembly
Loosen the nuts (54) and remove the foot (07) and the discharge flange (34). Pull out the tie bars (29/29A) and then remove
the stator (22); if necessary, secure the rotor (21) by holding the shaft complement (26) through the support flange window
(06A). Remove the screws (52) and washers (53). Pull out the pump casing (01) from the front end. Loosen the countersunk
screws (50) to remove the hollow bolt (27) and the rotor (21). Proceed likewise on the other end of the connecting rod (24) in
order to remove it.
Assembly
Connect the connecting rod (24) to the shaft complement (26) using the hollow bolt (27) and secure then with the washers
(35) and countersunk screws (50), is need to add sealing threaded fasteners LOCTITE 270 to ensure no loosens. Attach the
rotor (21) to the other end of the connecting rod (24) using the second hollow bolt (27). Introduce the pump casing (01) and
fasten it with the screws (52) and washers (53). Install the stator (22) and, if necessary, secure the rotor (21) by holding the
shaft complement (26). Install the tie bars (29/29A), the discharge flange (34) and the foot (07), securing everything with the
nuts (54).

2016/02 7.Maintenance 13
ATTENTION! When installing the new seal, use soapy water when fitting the
different parts and gaskets to allow them to slide better; apply to the stationary as
well as the rotating parts.
7.4.2. Mechanical seal
Disassembly
First proceed to the disassembly according to the preceding section.
Loosen the studs (55) and pull out the seal ring (31). Remove the rotating part of the mechanical seal which can be found in
the shaft complement (26). Remove the seal cover (09) to pull out the seal at the same time as the mechanical seal (08).
Finally, gently remove the stationary part of the seal, which has remained housed inside the seal cover.
Assembly
Fit the stationary part of the mechanical seal (08) and the O-ring (80) on the seal cover (09). Place the cover on the support
flange (06A). Slide the rotary part of the mechanical seal on the shaft complement (26). Place the seal ring (31) on the shaft
complement and fasten it with the studs (55) according to the following assembly dimensions
Pump type
A
KSF-20
12
KSF-25/30
16.5
KSF-40/50
23
KSF-60/80
25.5

14 7.Maintenance 2016/02
7.4.3. Change of drive
Disassembly
First proceed to the disassembly according to the preceding section.
Remove the elastic pin (05) from the shaft complement (26). Remove the screws (52A) and the washers (53A) and pull out the
drive (93).
INSTALLATION
Drill a hole in the drive shaft as shown in the figure
below. Mount the drive (93) on the flange support (06A)
and fasten it with the screws (52A) and washers (53A). Slide the shaft complement
(26) over the drive shaft (93) and fasten it with the pin (56).
Pump type
A
D
d
KSF-20
20
19/20
24
6
8
KSF-25/30
20
24/25/28
8
KSF-40/50
30
24/25/28
30/32/35
8
10
KSF-60/80
35
35/38
40/42
10
12

2016/02 8.Technical Specifications 15
8. Technical Specifications
8.1. TECHNICAL SPECIFICATIONS
Range of operating temperatures ...........................................
-10 ºC to +85ºC (14 ºF to +185 ºF)
Noise level ...........................................................................
60-80 dB(A)
Suction / discharge connections ............................................
DIN 11851 (standard)
Use special protection if the noise level in the work area exceeds 85 dB(A).
Pump type
With mechanical variable speed drive
With variable frequency drive
Flow rate
(1)
[m3/h]
Pressure
[bar] (2)
Speed
[RPM]
Power
[kW]
Flow rate
(1)
[m3/h]
Pressure
[bar] (2)
Speed
[RPM]
Power
[kW]
KSF-20
0.3 - 1.65
max. 6
190-1000
0.75
0.35 - 1.65
max. 6
200-1000
0.75
KSF-25
0.7 - 4
1.85
0.75 –4
2.2
KSF-30
1.1 –6
1.2 –6
KSF-40
2.5 –10
190-650
3
1.75 –10
125-650
3
KSF-50
5 –15
190-550
4
3.5 –15
125-550
4
KSF-60
7 –20
150-400
5.5
5 –20
100-400
5.5
KSF-80
20 - 45
max. 4
190-400
7.5
10 - 45
max. 4
100-400
7.5
(1) Nominal flow for liquids at a maximum pressure of 2 bar
(2) Maximum pressure with the power indicated above
Materials
Parts in contact with the product ...........................................
AISI 316L
Other stainless steel parts .....................................................
AISI 304
Stator and seals in contact with the product ...........................
NBR
Other optional materials .......................................................
Contact the supplier
Surface finish .......................................................................
Ra 0.8 polished
Mechanical seal
Type of seal .........................................................................
Simple internal seal
Material of the stationary part ...............................................
ceramic
Material of the rotary part .....................................................
graphite
Material of stator and seals ...................................................
NBR
8.2. WEIGHTS
Pump type
Weight
[kg]
Weight
[lbs]
KSF-20
62
137
KSF-25
79
174
KSF-30
80
176
KSF-40
130
287
KSF-50
145
320
KSF-60
265
584
KSF-80
285
628

16 8.Technical Specifications 2016/02
8.3. DIMENSIONS KIBER KSF FOR WINE PUMP WITH TROLLEY
PUMP TYPE
DN
A
B
C
D
E
F
KSF-20 *
40 (1½”)
325
1040
500
216
905
83
KSF-25
50 (2”)
439
1340
560
293
980
93
KSF-30
290
96
KSF-40
65 (2½”)
637
1625
308
108
KSF-50
80 (3”)
712
1675
304
132
KSF-60 *
100 (4”)
864
1790
530
345
975
135
KSF-80 *
984
1910
* With three-wheel trolley
8.4. DIMENSIONS KIBER KSF FOR WINE PUMP WITH BY-PASS
PUMP TYPE
DN
A
B
C
KSF-20
40 (1½”)
475
230
330
KSF-25
50 (2”)
613
262
360
KSF-30
KSF-40
65 (2½”)
831
294
385
KSF-50
80 (3”)
913
334
420
KSF-60
100 (4”)
1104
375
475
KSF-80
1224

2016/02 8.Technical Specifications 17
8.5. EXPLODED VIEW OF KIBER KSF FOR WINE PUMP

18 8.Technical Specifications 2016/02
8.6. PARTS LIST KIBER KSF FOR WINE PUMP
Item
Description
Quantity
Material
01
Body
1
AISI 316L
06A
Flange support
1
GG-15
07
Foot
1
AISI 304
08
Mechanical seal
*
1
-
09
Seal cover
1
AISI 304
21
Rotor
1
AISI 316L
22
Stator
*
1
-
24
Connecting rod
1
AISI 316L
26
Shaft complement
1
AISI 316L
27
Hollow bolt
*
2
AISI 316L
29
Upper tie bar
2
AISI 304
29A
Lower tie bar
2
AISI 304
31
Seal stop ring
1
AISI 316L
34
Discharge nozzle
1
AISI 316L
35
Pin washer
4
AISI 316L
47A
Protection
2
Plastic
50
Countersunk screw
4
A2
50A
Screw
4
A2
52
Hexagonal screw
4
A2
52A
Hexagonal screw
4
A2
53
Grower washer
4
A2
53A
Grower washer
4
A2
54
Cap nut
4
A2
55
Stud
3
A2
56
Pin
1
Steel
80
O-ring
*
1
NBR
93
Drive
1
-
(*) Recommended spare parts.

NOTES

INOXPA, S.A.
BANYOLES
Tel. [phone]
[email protected]
DELEGACIÓN NORDESTE
BARCELONA
Tel. [phone]
[email protected]
DELEGACIÓN CENTRO
MADRID
Tel. [phone]
[email protected]
DELEGACIÓN LEVANTE
VALENCIA
Tel. [phone]
[email protected]
DELEGACIÓN SUR
CADIZ
Tel. [phone]
[email protected]
SUMINISTROS TECNICOS
ALIMENTARIOS, S.L.
VIZCAYA
Tel. [phone]
[email protected]
DELEGACIÓN VALLADOLID
Tel. [phone]
[email protected]
DELEGACIÓN GALICIA,
ASTURIAS y LEÓN
Tel. [phone]
[email protected]
INOXPA SOLUTIONS
FRANCE,SARL
LYON
Tel. [phone]
[email protected]
PARIS
Tel. [phone]
[email protected]
S.T.A. PORTUGUESA LDA
ALGERIZ
Tel. [phone]
[email protected]
IMPROVED SOLUTIONS
PORTUGAL LDA
VALE DE CAMBRA
Tel. [phone]
[email protected]
INOXPA SKANDINAVIEN A/S
DENMARK
Tel. [phone]
[email protected]
INOXPA ITALIA, S.R.L.
VENEZIA
Tel. +39 041 - 411236
[email protected]
INOXPA UK LTD
KENT
Tel. [phone]
[email protected]
INOXRUS
SAINT PETERSBURG
Tel. [phone]
[email protected]
MOSCOW
Tel. [phone]
[email protected]
INOXPA UKRAINE
KIEV
Tel. [phone]
[email protected]
INOXPA COLOMBIA SAS
BOGOTÁ
Pbx 57-1-7427577
[email protected]
INOXPA USA, INC
CALIFORNIA
Tel. [phone]
[email protected]
INOXPA AUSTRALIA PTY, LTD
MORNINGTON
Tel. [phone]
[email protected]
INOXPA SOUTH AFRICA
GAUTENG
Tel. [phone]
[email protected]
INOXPA ALGERIE S.A.R.L.
ALGER
Tel. [phone]
[email protected]
INOXPA SPECIAL PROCESSING
EQUIPMENT (JIAXING), CO., LTD.
JIAXING, CHINA
Tel.: [phone]
[email protected]
INOXPA INDIA PRIVATE LIMITED
MAHARASHTRA
Tel. [phone]
[email protected]
INOXPA MIDDLE EAST
DUBAI, UAE
Tel. [phone]
[email protected]
In addition to our branches, INOXPA has a network of independent distributors in over 50 countries worldwide. For further information, visit our
website. www.inoxpa.com
Information is for guidance only. We reserve the right to modify any material or characteristic without prior notice.