INOXPA SLR-A Manual

INSTALLATION, SERVICE AND
MAINTENANCE INSTRUCTIONS
SLR-A
INOXPA, S.A.
c/Telers, 54 Aptdo. 174
E-17820 Banyoles - Girona (Spain)
Tel.: (34) 972 - 57 52 00
Fax.: (34) 972 - 57 55 02
Email: [e-mail]
www.inoxpa.com
Original Manual
01.505.30.00EN
(B) 2021/11

4 1.Safety 2021/11
1. Safety
1.1. INSTRUCTION MANUAL
This manual contains information regarding the reception, installation, operation, assembling, disassembling and maintenance
of the SLR-A pump.
The information published in the instruction manual is based on updated information.
INOXPA reserves the right to modify this instruction manual without prior notice.
1.2. INSTRUCTIONS FOR START-UP
This instruction manual contains essential and useful information for properly starting the pump and maintaining it in good
operating condition.
Prior to starting the pump, personnel and operators must carefully read the safety instructions detailed in this chapter and must
familiarize themselves with the operating characteristics of the pump; also, personnel and operators should strictly follow the
instructions provided. It is of vital importance that these instructions be maintained at a fixed location near the installation.
1.3. SAFETY
1.3.1. Warning symbols
Danger for persons in general.
Risk of injury caused by the rotary parts
of the equipment.
Electrical hazard.
Danger! Caustic or corrosive agents.
Danger! Suspended loads.
Danger for the proper operation of the
machine.
A safe working environment must be
ensured at all times.
The use of safety glasses is mandatory.
1.4. GENERAL SAFETY INSTRUCTIONS
Please carefully read this instruction manual prior to installing and starting up the pump. Contact
INOXPA in the case of any doubts or questions.
1.4.1. During the installation
You must read and take into account the Technical specifications in Chapter 8 at all times.
Do not start the pump until it has been connected to the pipework.
Do not start the pump unless the pump body has been mounted and adjusted and the pump rotors
have been fastened.
Ensure that the specifications of the drive are the proper ones; especially if there is a risk of
explosion due to the particular operating conditions.
During the installation procedure, electrical work must be carried out by properly authorized
personnel.
1.4.2. During operation
Make sure to take into account the Technical specifications in Chapter 8 at all times. The specified limit
values shall NEVER be exceeded.
NEVER touch the pump or the pipework during operation if the pump is being used for transferring
hot liquids or during cleaning.

2021/11 1.Safety 5
The pump has moving parts. Never place your fingers inside the pump during operation.
NEVER operate with the suction and discharge valves closed.
NEVER spray the electrical motor directly with water. The standard protection of the motor is IP-55:
Protection against dust and water spray.
1.4.3. During maintenance
The Technical specifications in Chapter 8 shall always be observed.
NEVER disassemble the pump until the pipes have been emptied. Remember that liquid will remain
inside the pump’s body (if does not have a purge). Bear in mind that the pumped liquid may be
hazardous or extremely hot. Consult the regulations in effect in each country for these cases.
Do not leave loose parts on the floor.
ALWAYS disconnect the electrical power to the pump prior to carrying out any maintenance. Remove
the fuses and disconnect the cables from the motor’s terminals.
All the electric work should be carried out by authorised personnel.
1.4.4. Compliance with the instructions
The non-compliance with any of the instructions may impose a hazard for operators, the atmospheric conditions of the room
and for the machine; also, it may cause the loss of any right of claiming damages.
These non-compliances may result in the following hazards:
•Important failures of the machine's/plant's operation.
•Non-compliance with specific maintenance and repair procedures.
•Possibility of creating electric, mechanical and chemical hazards.
•The atmospheric conditions in the room may impose a hazard due to the substances that are released.
1.4.5. Warranty
We wish to emphasize that any warranty provided will be void and that we have the right to receive compensation in the case
of any civil responsibility claim by products presented by third parties in the following cases:
•The operation and maintenance work has not been carried out in accordance with the corresponding service
instructions; the repairs have not been carried out by our personnel or they have been carried out without our
written authorization;
•Modifications have been carried out of our products without our prior written authorization;
•The parts or lubricating agents used are not original INOXPA parts/lubricants;
•The material has been improperly used due to errors or negligence or it has not been used according to the
indications and for the desired purpose.
•The pump parts have been damaged by high pressure due to not having used a safety or relief valve.
The supplied General Conditions of Delivery also apply.
No modification of the machine is permitted without prior authorization from the manufacturer. For
your safety, use only original spare parts and accessories. The usage of other parts will relieve the
manufacturer of any liability.
Any change in the operating conditions shall be conducted only with the previous written
authorization of INOXPA.
Please contact us in case of any doubt or if you require a more detailed explanation regarding particular data
(adjustment, assembly, disassembly, etc.).

6 2.Table of contents 2021/11
2. Table of contents
1. Safety............................................................................................................................................. 4
1.1. Instruction manual................................................................................................................................. 4
1.2. Instructions for start-up ......................................................................................................................... 4
1.3. Safety ................................................................................................................................................... 4
1.4. General safety instructions ..................................................................................................................... 4
2. Table of contents ........................................................................................................................... 6
3. General information ...................................................................................................................... 7
3.1. Description ............................................................................................................................................ 7
3.2. Principle of operation ............................................................................................................................. 7
3.3. Application ............................................................................................................................................ 7
4. Installation .................................................................................................................................... 9
4.1. Reception of the pump........................................................................................................................... 9
4.2. Transport and storage............................................................................................................................ 9
4.3. Location ...............................................................................................................................................10
4.4. Piping ..................................................................................................................................................10
4.5. Electrical installation .............................................................................................................................11
5. Start-up ....................................................................................................................................... 12
5.1. Start-up ...............................................................................................................................................12
5.2. Safety valve..........................................................................................................................................13
6. Operating problems..................................................................................................................... 14
7. Maintenance ................................................................................................................................ 15
7.1. General considerations ..........................................................................................................................15
7.2. Storage ................................................................................................................................................15
7.3. Cleaning...............................................................................................................................................16
7.4. Disassembly of the pump ......................................................................................................................17
7.5. Assembly of the pump...........................................................................................................................20
7.6. Setting and synchronizing the lobes .......................................................................................................22
7.7. Assembly / disassembly of the mechanical seal option ............................................................................23
8. Technical Specifications .............................................................................................................. 24
8.1. Technical specifications .........................................................................................................................24
8.2. Weights................................................................................................................................................24
8.3. Options ................................................................................................................................................24
8.4. SLR-A dimensions .................................................................................................................................25
8.5. Rectangular port dimensions .................................................................................................................25
8.6. SLR-A parts breakdown.........................................................................................................................26

2021/11 3.General information 7
3. General information
3.1. DESCRIPTION
INOXPA's SLR-A lobe pumps are part of our wide range of positive displacement rotary pumps for viscous liquids.
Thanks to the wider lobes installed in the SLR-A pump, it has a greater flow, appropriate for pressures of up to 6 bar.
The SLR-A model has been developed in order to meet all hygiene requirements of the food industry.
Regarding hygiene, reliability and robustness, the complete range of lobe pumps satisfies all the requirements of the
aforementioned industry.
Thanks to its modular design, there is an optimum interchangeability of parts between the different pumps.
This unit is approved for use with food products.
3.2. PRINCIPLE OF OPERATION
The lobe pump is a positive displacement rotary pump. The upper lobe is actuated by the drive shaft. The lower lobe is located
on the driven shaft and is driven by a helical gear. Both lobes rotate in sync without touching each other. During the operation
of the pump, they displace a fixed volume of liquid. The following figure shows how a lobe pump operates.
A: As the lobes rotate, the space on the suction side increases because one lobe separates from the other, causing a partial
vacuum that pushes the liquid into the pumping chamber.
B: Each lobe is filled consecutively as the shafts rotate and the liquid is displaced towards the discharge side. The small
clearances that exist between the lobes and between the lobes and walls of the pump body cause the spaces to properly close.
C: The pump body is completely filled and liquid escapes through the meshing of the lobes, pushing against the walls of the
spaces, thus completing the pumping action.
NOISE
Lobe pumps are rotary displacement pumps. Owing to the contact between internal parts, pressure variations, etc., these
pumps are louder than centrifugal pumps.
This noise originating from the operation and installation must be considered.
When the noise level in the operating area exceeds 85 dB (A), special protection must be used.
3.3. APPLICATION
The SLR-A lobe pump has been designed for pumping olive paste and olive-mill waste ('alperujo'), and its applications are:
•Decanter feeding with olive paste.
•Decanter feeding with 2-phase olive press 'orujo' waste.
•Short distance transfers:
- Filling of tanks.
- Top feeding of 'orujo' into hoppers
- Feeding of blenders for centrifuging

8 3.General information 2021/11
3.3.1. Field of application
The field of application for each type of pump is limited. Each pump is ordered to meet specific
pumping conditions. INOXPA will not be liable for any damage that may occur if the information
provided by the buyer is incomplete (specifications of the liquid, RPM, etc.).
01.505.32.0002

2021/11 4.Installation 9
4. Installation
4.1. RECEPTION OF THE PUMP
INOXPA is not liable for any deterioration of the material caused by its transport or unpacking.
Visually check that the packaging has not been damaged.
The following documentation is included with the pump:
•Shipping documents.
•Instructions and Servicing manual for the pump.
•Instructions and Servicing manual for the geared motor.
Unpack the pump and check the following:
•The pump's suction and discharge connections.
•Removing any packaging material remains.
•Check that the pump and motor have not suffered any damage.
•If not in good material condition and/or if not all the parts are
included, the shipping carrier should submit a report as soon as
possible.
4.1.1. Identification of the pump
MODEL Nº
kW
YEAR
-1
min V
Qm /h Hm
Hz
3
17820 BANYOLES · GIRONA (SPAIN)
www.inoxpa.com
INOXPA S.A.
Name plate on the pump
4.2. TRANSPORT AND STORAGE
The SLR-A pumps are usually too heavy to be stored manually. Use an adequate means of transport.
Use the points indicated in the diagram for lifting the pump.
The pump should only be transported by authorized personnel.
Do not work or walk underneath heavy loads.
Lift the pump as indicated below:
•Always use two supporting points
located as far away from each other
as possible.
•Fasten the points in a manner that
prevents them from sliding.
•Refer to Chapter 8 Technical
specifications in order to verify the
dimensions and weights.
Serial number
01.505.32.0004
01.505.32.0003

10 4.Installation 2021/11
4.3. LOCATION
•Place the pump as close as possible to the suction tank and if possible, below the liquid level.
•Place the pump in a position that allows enough space around it to provide access to the pump as well as to the motor. (Refer to
Chapter 8 Technical specification to verify the dimensions and weights).
•Place the pump on a flat and level surface.
•The base must be rigid, horizontal and protected against vibrations.
Install the pump in a manner that provides it with adequate ventilation. If the pump is installed
outside, it must be sheltered under a roof. Its location must allow for easy access during any
required inspection or maintenance task.
4.4. PIPING
•In general, suction and discharge pipes must be installed in straight sections, with the minimum number of elbows and fittings in
order to reduce wherever possible any head losses that may be caused by friction.
•Ensure that the pump ports are properly aligned with respect to the pipes and they are of a similar diameter size as the pipe
connections.
•Place the pump as close as possible to the suction tank and whenever possible below the liquid level or even at a lower level with
respect to the tank in order to ensure that the gauge height of the static suction is at its maximum point.
•Place the pipe support clamps as close as possible to the pump's suction and discharge ports.
4.4.1. Shutoff valves
The pump may be isolated for maintenance. For this, shutoff valves must be installed and connected to the pump's suction
and discharge connections.
These valves must ALWAYS be open when the pump is operating.
4.4.2. Self-priming process
In general terms, if the self-priming process is followed, the pump must contain sufficient liquid to fill all internal recesses and
voids, allowing the pump to generate a difference in pressure.
However, if low viscosity fluids are pumped, a foot valve of the same or greater diameter than that of the suction pipe must be
installed; as an alternative, a "U" shaped pipe may be installed.
The use of a foot valve is not recommended for pumping viscous liquids.
•To eliminate the air and gases from the suction line, the counter pressure inside the discharge line must be decreased.
When the self-priming process is used, the pump must be started by opening and closing the feed line, which allows the
air and gases to escape to a lesser counter pressure.
•Another option involves the use of long pipes or the installation of a check valve in the discharge line; it is also possible to
install a by-pass with a shut-off valve on the discharge side of the pump. This valve must be opened for priming, which
allows air and gases to escape with a minimum counter-pressure.
•The by-pass must not return to the suction port, it should go to the supply tank instead.
01.505.32.0005

2021/11 4.Installation 11
4.5. ELECTRICAL INSTALLATION
Only allow qualified personnel to connect the electrical motors. Take the necessary steps to prevent
any failure of connections and cables.
The electrical equipment as well as the terminals and control system components may remain
electrically charged even when they are disconnected. Contacting them may impose a hazard to
operators or cause irreparable material damage.
Prior to handling the valve, ensure the motor is stopped.
•Connect the motor in accordance with the instructions supplied by the motor manufacturer.
•Verify the direction of rotation (refer to the label located on the pump).
•Briefly start up the pump motor. Ensure that the pumping direction is correct. Operating the pump in the wrong
direction may cause serious damage.
ALWAYS verify the direction of the pump with liquid inside the pump.
01.505.32.0006

12 5.Start-up 2021/11
5. Start-up
Prior to starting the pump, carefully read and follow the installation instructions given in Chapter 4
Installation.
5.1. START-UP
Carefully read Chapter 8 Technical specifications. INOXPA will not be liable if the equipment is
improperly used.
Do not touch the pump or the pipework while high temperature products are being pumped.
5.1.1. Inspections that must be carried out prior to starting the pump
•Completely open the shut-off valves on the suction and discharge lines.
•Check the pump oil level. Add the proper amount of oil as required to maintain the level at the centre of the oil sight glass (when
starting up for the first time: the pumps are shipped with oil in the bearing support. However, this check must always be
performed).
•If liquid does not flow to the pump, fill it up with the liquid to be pumped.
The pump shall NEVER turn with no fluid inside.
•Check that the electrical power supply coincides with the power rating indicated on the motor plate.
•Check for proper direction of rotation of the motor.
•If the pump has a double mechanical or cooled seal, install the corresponding secondary connection with the values indicated in
Chapter 8, Technical specifications.
•
5.1.2. Inspections that must be carried when starting the pump
•Check that the pump is not making any strange noises.
•Check that the absolute inlet pressure is sufficient to prevent cavitation of the pump. Refer to the curve for the minimum pressure
required above the vapour pressure (NPIPr).
•Control the discharge pressure.
•Check that the seals are not leaking.
The shutoff valves must not be used to regulate the flow in the suction line. It must be completely
open during operation.
Control the power consumption of the motor to prevent an electrical overload.
If required, decrease the flow and the power consumed by the motor by decreasing the motor speed.

2021/11 5.Start-up 13
5.2. Safety valve
The opening pressure adjustment of the safety valve is carried out at the INOXPA workshops. However, the pressure at which
the valve opens depends on the fluid to be pumped, the viscosity, the rpm, etc., which means that prior to starting the pump,
the user must set the opening pressure of the safety valve.
5.2.1. Safety valve setting
When the pump incorporates a safety valve and the pressure setting of the valve is not indicated, the valve is adjusted to the
pump's maximum working pressure. The user must verify this by observing the position of the pressure nut (37). At maximum
set pressure, the pressure nut is located at the lower part of its travel.
In order to obtain the proper opening pressure, follow the procedure below:
•Loosen the counter nut (37A).
•Use a spanner to turn the pressure nut (37) to the left to reduce the spring tension and obtain the desired opening pressure.
•When the desired opening pressure is obtained, tighten the counter nut (37A).
When checking the safety valve setting you must ensure that the pump pressure NEVER exceeds the
set pressure + 2 bars.
When the safety valve is not operating properly, the pump must immediately be placed out of service.
The valve must be verified by INOXPA's technical service personnel.

14 6.Operating problems 2021/11
6. Operating problems
The following table provides solutions to problems that may appear during normal pumping operations. It is hereby assumed
that the pump has been installed properly and it has been properly selected for the pertinent application.
Contact INOXPA if technical assistance is required.
Operating problem
Probable causes
Motor overload.
8, 9, 12, 16, 20, 21, 22, 23.
The pump flow or pressure is insufficient.
2, 4, 5, 7, 8, 9, 10, 11, 13, 14.
No pressure on the discharge side.
1, 2, 3, 6, 7, 15.
Irregular discharge flow rate / pressure.
2, 4, 5, 6, 9, 12.
Noise and vibrations.
2, 4, 5, 6, 7, 8, 9, 11, 12, 13, 16, 19, 20, 21, 22, 23, 24.
The pump gets clogged.
8, 9, 11, 16, 19, 20, 21, 22, 23, 24.
Pump overheated.
7, 8, 9, 11, 12, 16, 20, 21, 22, 23.
Abnormal wear.
4, 5, 11, 16, 19, 23, 24.
Leak through the mechanical seal.
17, 18.
Probable causes
Solutions
1
Wrong direction of rotation.
Invert the direction of rotation
2
NPIP insufficient.
Increase the NPIP:
•Raise the suction tank
•Lower the pump
•Reduce the speed
•Increase the diameter of the suction pipe
•Shorten and simplify the suction line.
3
The pump is not purged.
Purge or fill with product.
4
Cavitation.
Increase the suction pressure. (refer to Section 2)
5
The pump sucks air.
Inspect the suction line and all of its connections.
6
Suction pipe obstructed.
Check the suction line and the filter/s if applicable.
7
Incorrect safety valve setting.
Verify the setting of the safety valve.
8
Discharge pressure is too high.
If required, reduce the head loss by increasing the diameter of
the discharge pipe.
9
Liquid viscosity is too high.
•Reduce the speed of the pump
•Reduce the viscosity; for example, by heating the liquid.
10
Liquid viscosity is too low.
•Increase the speed of the pump
•Increase the viscosity; for example, by cooling the liquid.
11
Liquid temperature is too high.
Reduce the temperature of the liquid.
12
The pump speed is too high.
Reduce the speed of the pump.
13
The lobes are worn.
Replace the lobes.
14
The pump speed is too low.
Increase the speed of the pump.
15
The shutoff valve on the suction side is closed.
Check and open.
16
Bearings are worn.
Replace the bearings, inspect the pump.
17
Seal gaskets are worn or damaged.
Replace the seal gaskets.
18
The gaskets are not adequate for the liquid.
Install the correct gaskets; consult with the supplier.
19
Gears are worn.
Replace and re-adjust the gears.
20
Insufficient lubricating oil level.
Fill with oil.
21
Improper lubricating oil.
Use an appropriate type of oil.
22
Friction in the lobes.
•Reduce the speed of the pump
•Reduce the feed pressure.
•Adjust the play
23
Tension in the pipework.
Connect the pipes to the pump without tension.
24
Foreign objects in the liquid.
Install a filter in the suction line.
If the problem persists, stop using the pump immediately. Contact the pump manufacturers or
representatives.

2021/11 7.Maintenance 15
7. Maintenance
7.1. GENERAL CONSIDERATIONS
Just like any other machine, this pump requires maintenance. The instructions included in this manual cover the identification
and replacement of spare parts. These instructions have been prepared by the maintenance personnel and are aimed at those
responsible for the supply of spare parts.
Carefully read Chapter 8 Technical specifications .
All parts or materials that are replaced must be properly disposed of / recycled in accordance with
the current directives applicable in each area.
ALWAYS disconnect the pump prior to starting any maintenance action.
7.1.1. Check the seal gaskets.
Periodically check that no leaks are present around the shaft. If the seal gaskets leak, replace the gaskets in accordance with
the instructions provided in Section 7.4.5 Removal of the lip seals.
7.1.2. Tightening torque
Material
Tightening torque [Nm]
M5
M6
M8
M10
M12
M14
M16
M18
M20
8.8
6
10
25
49
86
135
210
290
410
A2
5
9
21
42
74
112
160
210
300
7.1.3. Lubrication
The bearings are lubricated by immersion in an oil bath.
The pumps are supplied with oil.
•Periodically check the oil level; for example, weekly or every 150 hours of operation.
•The first oil change must be carried our after 150 hours or operation.
•Afterwards, it may be changed every 2,500 hours of operation or at least once a year under normal operating conditions.
When changing the oil: the oil collector must be filled to the half mark on the oil sight glass.
Do not fill the bearing support with oil above that level.
Stop the pump for a moment and then re-check the oil level; if required, add a little oil.
•The oil capacity of the SLR-A pump is 1.5 litres.
•Oils for temperatures between 5 and 50ºC: SAE 90 or ISO VG 220.
7.2. STORAGE
Prior to storing, the pump must be completely drained of fluids. Where possible, avoid exposing the parts to excessively humid
environments.

16 7.Maintenance 2021/11
7.3. CLEANING
7.3.1. Manual cleaning
The use of aggressive cleaning products such as caustic soda and nitric acid can burn the skin.
Use rubber gloves during the cleaning process.
Always use protective goggles.
7.3.2. Automatic CIP (cleaning-in-place)
If the pump is installed in a system with CIP, dismantling of the pump is not required.
The minimum recommended liquid speed for an effective cleaning process is 1.8 m/s (minimum Reynolds number > 100 000 at
1.0~2,5 bar).
If an automatic cleaning system is not available, disassemble the pump in accordance with the instructions supplied in the
section called Assembly and Disassembly of the pump.
Cleaning solutions for CIP processes.
Only use clear water (chlorine free) for mixing with the following cleaning agents:
a) Alkaline solution: 1% by weight of caustic soda (NaOH) at 70ºC (150ºF)
1 kg NaOH + 100 litres of water = cleaning solution
or
2.2 litres NaOH at 33% + 100 litres of water = cleaning solution
b) Acid solution: 0.5% by weight of nitric acid (HNO3) at 70ºC (150ºF)
0.7 litres of 53% HNO3+ 100 litres of water = cleaning solution
Check the concentration of the cleaning solutions; incorrect concentrations may lead to the
deterioration of the pump seals.
To remove any residues of cleaning products, ALWAYS perform a final rinse with clean water upon completion of the cleaning
process.

2021/11 7.Maintenance 17
7.4. DISASSEMBLY OF THE PUMP
The assembling and disassembling of the pumps must only be carried out by qualified personnel. Ensure that personnel
carefully read this instruction manual and, in particular, the instructions relative to the work that is to be carried out.
Improper assembling or disassembling may cause damage that may affect the operation of the
pump and result in high repair costs as well as a long period of inactivity.
INOXPA will not be liable for accidents or damage caused by non-compliance with the instructions
included in this manual.
Preparations
Provide for a clean working environment since some parts, including the mechanical seal, may need to be handled carefully and
others have small tolerances.
Check that the parts used have not been damaged during transport. Upon doing this, the adjustment edge, coinciding faces,
the tight seal, presence of burrs, etc., must be inspected.
After every disassembly, carefully clean the parts and check for any damage. Replace all damaged parts.
Tools
Use the adequate tools for carrying out the assembling and disassembling. Use the tools properly.
Cleaning
Prior to disassembling the pump, clean the exterior and interior of the pump.
NEVER clean the pump by hand while it is operating
7.4.1. Removing the pump cover and the front wear plate
CAUTION! Liquid from the pump body may spill when the pump cover is removed
•Close the suction and discharge valves.
•Remove the cap nuts (45). Notches are available at four points around
the pump cover (03) to help remove it (using a screwdriver) from the
body if required.
•Remove the front wear plate (32A).
•Check that the gasket (80A) is in good material condition.
7.4.2. Disassembly of the lobes
•Use an Allen key 14 to loosen the screws (25).
•Remove the screws (25) and the screw cap (85B) these screws have a
right-hand thread. To prevent the lobes from turning simultaneously, a
wooden or plastic block may be placed between the lobes.
•Check that the O-rings (80)(80G) are in good material condition.
•Remove both lobes (02). If required, use a tool for this task.
01.505.32.0008
01.505.32.0009

18 7.Maintenance 2021/11
7.4.3. Disassembly of curved wear plates
•Loosen the flange screws (51A).
•Remove the curved wear plates (13C).
7.4.4. Disassembly of the body
•Loosen and remove the nuts (54A) that fasten the body to the bearing
support (06)
•Separate the rear wear plate (32B) and the seal cover (09).
•Check that the gaskets (80A) are in good material condition.
•Remove the sleeve (13) and inspect the sleeve's O-ring (80D).
7.4.5. Removal of the lip seals
•Loosen and remove the screws (52) that fasten the counter cover (11) to
the seal cover (09); the counter cover includes two M6 bores to facilitate
its removal (S).
•Remove the lip seal cover (09B) and check the condition of the lip seals
(08).
•Check the material condition of the O-ring (80B).
•
7.4.6. Disassembly of the drive
•Loosen and remove the screws (52B) that fasten the drive (93) to the
bearing cover (12)
•Remove the drive (93), if required use a tool for this task; with the drive,
the coupling flector (40) will be released.
01.505.32.0010
01.505.32.0011
01.505.32.0012
01.505.32.0013

2021/11 7.Maintenance 19
7.4.7. Draining the lubrication oil
•Place a container below the bearing support (06) to collect the lubricating
oil for its disposal.
•Remove the drain cap (87) that is located on the rear side of the bearing
support (06).
•
7.4.8. Disassembly of the shaft assembly
•Loosen the threaded stud (55D) through the hole located below the
bearing cover (12) and remove coupling (41A).
•Loosen and remove the screws (52E).
•Remove the bearing cover (12) to check the condition of the bearing cover
gasket (18). If any defect is found, find a spare prior to assembling the
pump.
•
01.505.32.0014
01.505.32.0015

20 7.Maintenance 2021/11
7.5. ASSEMBLY OF THE PUMP
7.5.1. Assembly of the shaft assembly
•Check that the bearing cover gasket (18) is not damaged and mount it in
the proper position on the bearing cover (12).
•Place the bearings cover (12) and fasten with screws (52E).
•Install the cotter pin (61A) of the drive shaft (05) and install the drive
plate (41A), tighten it with the threaded stud (55D) through the hole on
the bottom of the bearing cover (12).
•
7.5.2. Filling with lubricating oil
•Remove the oil cap (85) that is located on top of the bearing support
(06).
•Fill the bearing support (06) with lubricating oil to mid level of the oil sight
glass (86).
Refer to 7.1.3 Lubrication to find out what type and the quantity of oil
to use.
•
7.5.3. Assembly of the drive
•Place the coupling flector (40) and the drive coupling (41A) on the drive
shaft (93) and mount it on to the bearing cover (12).
•Tighten the screws (52B) that fasten it to the bearing cover (12).
7.5.4. Installation of the lip seals
•Place the lip seals (08) on the lip gasket cover (09B), apply food grease
between gaskets.
•Place the O-ring (80D) on the lip seal cover (09B) and install on the seal
cover (09).
•Install the seal cap (11) and fasten it with the screws (52).
01.505.32.0016
01.505.32.0017
01.505.32.0018
01.505.32.0019