Insignia Ns-a700pf6 User manual

NS-A700PF6 or NS-A700PF6-2 (LG)

1Press the push button on the lter housing.

2Gently pull the cartridge down and then pull it out

of the lter housing. You may need to lower or

remove the shelf below the cover.

3Ensure that o-rings are present on the cartridge

and are seated into grooves.

4Insert the new cartridge, pushing it in until it stops.

Push up rmly and close the cover.

5Reset the lter change indicator in your refrigera-

tor, if applicable. (See “RESETTING YOUR FILTER

INDICATOR” on back page.)

Note: Run approximately 1.5 gallons of water through

the new lter before use.

NS-A8001F6 or NS-A8001F6-2 (Maytag, PuriClean II, Amana,

Sears/Kenmore, Whirlpool and Kitchenaid)

1Twist the old lter counterclockwise and pull it out

of the receiver. The water automatically shuts o.

2Push the new lter into the lter receiver until it

stops.

3 Turn the new lter clockwise until it stops.

4Reset the lter change indicator in your refrigerator,

if applicable. (See“RESETTING YOUR FILTER

INDICATOR” on back page.)

Notes:

• Run approximately 1.5 gallons of water through the

new lter before use.

• Do not remove O-ring.

NS-LT600B-2 (LG and Kenmore)

1Remove the old lter by rotating a half turn

counterclockwise, then pull it out. The water

automatically turns o.

2If you have a Kenmore refrigerator, check if there is

a plastic or metal cap that covers the top of the old

lter. If there is, pull o the cap and attach it to

your new lter. If there is not, continue to step 3.

3Align the top of your new lter with the receiver,

then push it in until it stops.

4Rotate the lter a half turn clockwise to secure the

lter, then twist a little more to prevent leaks.

NS-DA2920 or NS-DA2920-2 (Samsung)

1Remove the old lter by rotating it a 1/4 turn

counterclockwise, then pull it out.

2Align the top of your new lter with the receiver,

then push it up until it stops.

3Rotate the lter a 1/4 turn clockwise to secure the

lter.

BEFORE USING YOUR FILTER

If your refrigerator has a change lter indicator, reset it. See “Resetting your

lter indicator” for instructions.

Quick Setup Guide |NS-A700PF6/NS-A700PF6-2/NS-A8001F6/NS-A8001F6-2/NS-LT600B-2/NS-DA2920/NS-DA2920-2

Refrigerator Filter

Before using your new product, please read these instructions to prevent any damage.

Congratulations on your purchase of one of the highest performing

water lters on the market today. Insignia lters use a high-grade

coconut carbon that has 50% more micro-pores than standard

carbon. They also use fewer high-compression binders, giving you the

best water ltration possible.

PACKAGE CONTENTS

• Refrigerator lter(s) (1 or 2 pack)

• Quick Setup Guide

GENERAL INSTALLATION GUIDELINES

1YOU MUST SOAK your new lter in water for 15 minutes prior to

installing it in your refrigerator. This is needed to remove air from

the carbon block.

2It is normal for black carbon nes (particles) to appear on the outside

of your lter. This happens when the lter is jarred in shipping, it is

safe, simply wipe it o.

3Connections on our lters are larger in size to prevent leakage. This

might require more hand leverage to install.

4 After installing, run about two to three gallons of water through your

refrigerator’s water dispenser to remove air and loose carbon pieces.

The water may be cloudy and sputter until the air is removed.

5 We apply a safe, NSF approved, food grade silicone lubricant to our

lter connectors (jelly like substance).

Installation:

*PUSH AND TURN HARD

To remove turn counter-clockwise

To install turn clockwise

Do not remove the O-ring

Filter receivers are designed to be exible.

Don’t worry, they won’t break!

CMY

NS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 1 9/16/2014 4:29:05 PMNS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 1 9/16/2014 4:29:05 PM

Get other manuals https://www.bkmanuals.com

RESETTING YOUR FILTER INDICATOR

Note: These are the most common lter reset instructions. If the instructions

don’t work for your refrigerator brand, see the documentation that came with

your refrigerator.

TROUBLESHOOTING

STORAGE AND MAINTENANCE

• Replace your lter every three to six months to prevent bacteria and

fungus growth in your lter, supply lines, and storage tank.

• Stored lters do not expire. Keep your unused lters in a cool, dark, and

dry place until you need them.

• If you do not use your water dispenser for more than four days, run two

gallons of water before using it to prevent bad tasting water.

• The lters are lubricated with a safe, USDA grade silicone. You do not need

to lubricate the gaskets or receiver before installing.

V3 ENGLISH 14-1039

RECYCLING YOUR USED INSIGNIA FILTER

Help the environment by recycling your used Insignia lter at your local

recycling facility or mail it to:

Insignia Filters

2678 Ram Bay Road

Manning, South Carolina 29102

ONEYEAR LIMITED WARRANTY

For complete warranty, visit www.insigniaproducts.com.

CONTACT INSIGNIA

1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)

www.insigniaproducts.com

CERTIFICATIONS: <SGF-M9, SGF-LB60, SGF-DA20B, SGF-LA07>

INSIGNIA is a trademark of Best Buy and its aliated companies.

Registered in some countries.

Distributed by Best Buy Purchasing, LLC

7601 Penn Ave South, Richeld, MN 55423 U.S.A.

Made in China

REFRIGERATOR

BRAND

Amana®

GE or Hotpoint

Samsung

Kenmore

Maytag® and

Jenn-Air®

Whirlpool® and

Kitchen Aid®

INSTRUCTIONS

Press and hold the dispenser lock and auto light buttons at the

same time. When the lter indicator ashes (about four seconds),

release both buttons.

Press and hold the dispenser lock and water buttons at the same

time. When the lter indicator ashes (about four seconds), release

both buttons.

Press and hold the dispenser lock and auto light buttons on the

dispenser (at the same time) for 4 seconds until the lter status

indicator begins to ash, and then release the buttons. On

some Amana fridges you need to press the dispenser lock and

water buttons for 4 seconds until the lter status indicator begins

to ash, and then release the buttons.

Press and hold the reset water lter button on the dispenser for

three seconds.

Press and hold the ice type and child lock buttons for three

seconds. The water lter indicator should turn green.

Note: Only hold these buttons for three seconds. Holding these

buttons for ve seconds cancels the reset. If you cancel the reset,

repeat the instructions above again.

Press and hold the reset button for three seconds.

The water lter reset for Kenmore refrigerators varies by model.

See the documentation that came with your refrigerator.

Press and hold the lock and light buttons (lock and water on newer

fridges) on the dispenser for about 4 seconds, until the indicator

light blinks.

Press the light switch 5 times within 10 seconds. If the fridge has a

lter button, press and hold it for 5-10 seconds

PROBLEM

My refrigerator is

not dispensing

water

My water

dispenser is

dripping

My water is cloudy

or contains black

carbon pieces

My new lter is

making noises or

sputtering

My water tastes

bad

SOLUTION

• Make sure that you soaked your lter in water for 15 minutes before

installing.

• Make sure that the lter is securely connected to the receiver. Do not

use tools to tighten the lter in place.

• Make sure that the water line to the refrigerator is turned on. The

valve must be completely open for the refrigerator to receive water.

• Make sure that the refrigerator door is closed or the dispenser will not

work.

• A few drops are normal. If the water is dripping constantly, have a

service technician check your refrigerator’s water valve.

• Cloudy water is caused by microscopic air bubbles. Run two to three

gallons of water from your dispenser to clear the air bubbles out.

• Black carbon pieces in the water are normal and appear with all

carbon lters. Run two to three gallons of water through your

dispenser to remove loose carbon pieces.

• Make sure that you soaked your lter in water for 15 minutes before

installing.

• Noises and sputtering are caused by trapped air pockets. Run two to

three gallons of water from your dispenser to push the air out.

• If you do not use your water dispenser for more than four days, run

two gallons of water through the dispenser before using it.

• Make sure that you replace your lter every three to six months to

prevent bacteria growth.

CMY

NS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 2 9/16/2014 4:29:12 PMNS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 2 9/16/2014 4:29:12 PM

Get other manuals https://www.bkmanuals.com

This manual suits for next models

Other Insignia Water Filtration System manuals