Insinger CENTURY 14 User manual

Item #_____________
CSI - 11400
CENTURY 14
AUTOMATIC THREE TANK
RACKLESS CONVEYOR
DISHWASHER
6245 State Road
Philadelphia, PA 19135-2996
215-624-4800
215-624-6966 FAX
800-344-4802
www.insingermachine.com
DESIGN
Automatic conveyor, flight type three tank dishwasher with
recirculating prewash, wash and rinse; and fresh water final rinse.
Capacity is 8,736 dishes per hour with a conveyor speed of 7 ft.
per minute. Designed for left or right hand conveyor travel, as
specified.
❏ Stainless steel steam coil
tank heat
❏ Pressure reduction valve and
line strainer
❏ Stainless steel belt with
removable rack sections
❏ S/S panels all sides
❏ Single point electrical connection:
motors, controls, and heaters
❏ Security package
❏ Electric booster
❏ Insulated hood and doors
❏ Totally enclosed motors
OPTIONAL ACCESSORY EQUIPMENT
STANDARD EQUIPMENT
● Exclusive CrossFire® Wash
system (patented)
● Tank heat: 50 KW electric
immersion heaters or steam
injectors
● Capillary thermometers for
prewash, wash, rinse
and final rinse
● Final rinse pressure gauge
● Vacuum breakers on all incoming
water lines
● Manifold cleanout brush
● Inspection and cleanout doors
● S/S frame, legs and feet
●
S/S front enclosure panel
● Automatic tank fill
● Low water protection
● Detergent connection provision
● SureFireTM Start-Up and
Check-Out Service
● Top mounted control panel
(NEMA 12)
● Steam booster
● Simplified scrap screen design
● Door safety switches
● Exhaust connections with
adjustable dampers
● Standard frame drip proof motors
● Conveyor reversing switch
● Polypropylene belt with
removable rack sections
● Conveyor safety stop bar
● Override switch for de-liming
● Interior work lights

3M 09/06 PRINTED IN USA
Information and specifications subject to change without notice
Capacity
per hour
Final rinse
consumption at
20 psi min.
Exhaust hood
requirement Peak rate
drain flow
Shipping
weight Current draw
amps Steam Electric
w/o booster
Tank capacity Motor size Electric usage Final rinse
peak flow at
20 psi min.
8,736 dishes
600-1300 meals
228 gals./hr.
500 CFM Load
1000 CFM Unload 23 gals./min. 2500 lbs.
13 gals. (prewash)
25 gals. (wash)
26 gals. (rinse)
1/2 hp (prewash)
2 hp (wash)
2 hp (rinse)
1/2 hp (conveyor)
20 kw wash tank
30 kw rinse tank
24 kw booster 40° rise
45 kw booster 70° rise
182 lbs./hr tank
81 lbs./hr booster 40°rise
142 lbs./hr booster 70°rise 3.8 gals./min.
Steam
consumption at
20 psi min.
208/3/60 ..................... 21.0 ....................160.0
240/3/60 ..................... 19.1 ....................139.6
480/3/60 ....................... 9.5 ......................69.5
380/3/50 ..................... 11.5 ......................87.5
CSI - 11400
Note: For all rough in connections see Installation and Layout Detail Drawing.
SPECIFICATIONS
CONSTRUCTION - Hood and tank all welded seamless construction using 16 gauge 18-8 type 304 S/S. S/S frame, legs and feet. All
internal castings are non-corrosive nickel alloy, bronze or S/S.
DOORS - Three extra large die formed 18-8 type 304 S/S front inspection doors riding in all S/S channels. A triple ply leading edge on the
door channels made of S/S with no plastic or nylon sleeves or liners used. Two intermediate S/S door safety stops on each door.
CONVEYOR-Removable polypropylene or S/S rack sections on S/S belt with polyethylene rollers. Conveyor drive system includes
large speed reducer with cut gears operating in oil bath and frictionless, trouble-free overload release system. Conveyer transports
dishware automatically through all washing and rinsing systems and is driven by an independent 1/2 HP motor. A trip bar at the end of the
unload section stops the conveyor if any ware reaches the bar. A reversing switch is provided to assist in removing jams in the belt.
PUMPS - Centrifugal type “packless” pump with a brass petcock drain. Construction includes ceramic seal and a balanced cast
impeller on a precision ground stainless steel shaft. All working parts mounted as an assembly and removable as a unit without
disturbing pump housing. Two 2 HP motors wash and rinse and 1/2 HP prewash, all standard horizontal C-face frame, drip-proof,
internally cooled with ball-bearing construction.
CONTROLS - Top-mounted control cabinet, NEMA 12 rated with heat insulation provided between hood and control cabinet, housing
motor controls and overload protection, transformer, contactors and all dishwasher integral controls. All controls safe low voltage 24 VAC.
ENERGY SAVER - Electric photo eye automatically operates the final rinse solenoid only when ware passes, saving water and
energy. The photo eye also activates an adjustable timer control. If no ware passes during the set time, the machine shuts down.
SPRAY SYSTEM - Spray arms are made of 18-8 type 304 stainless steel pipe. Spray assemblies removable without the use of tools.
PREWASH - Upper and lower manifolds. One manifold above with 3 power prewash nozzles, one manifold below with 3 power
prewash nozzles.
WASH - Upper and lower manifolds and CrossFire® Wash System (patented). Each manifold has 3 upper and 4 lower power wash arms
designed with pressure action cleansing slots. The slots are precision milled for water control producing a fan spray. Wash arms are fillet
welded to the S/S manifold. The CrossFire® system provides 2 horizontally spraying high pressure nozzles.
RINSE - Upper and lower manifolds. Each manifold has 3 upper and 4 lower power rinse arms designed with pressure action
cleansing slots. The slots are precision milled for water control producing a fan spray. Rinse arms are fillet welded to the S/S manifold.
FINAL RINSE - Eight nozzle assemblies above and four nozzles below threaded into schedule 40 pipes. Nozzle assemblies produce a
fan spray reducing water consumption, maximizing heat retention.
DRAIN - Drain valves externally controlled. Overflow assembly with skimmer cap is removable without the use of tools for drain line
inspection. Heaters protected by low water level control.
CENTURY 14