1Installation
Manual Linking
Support and Resources
For the complete Owner’s Manual and more, visit
insteon.com/get-started-2475f
Linking
Unlinking
Fan/Light On
Fan/Light Off
LIGHT
FAN
Status LED* Status LED
FanLight
Set Button Set Button
Fan (red)
Lights (blue)
Line (black)
Neutral (white)
Status LEDs
On Blinking
For safety, the fan motor cannot be
engaged by tapping the set button
Wait to test fan speed controls until
after re-installing your fan.
Insteon Ceiling Fan Controller
Quick Start Guide
Re-install Fan
3
A. Carefully remount cowling with Ceiling Fan Controller inside (or in electrical box)
B. Use the included cable tie to secure Ceiling Fan Controller to the fan’s bracket
Add to Insteon Hub
2
From within the Insteon for Hub app, select Add
a Device, and follow the instructions to add a
wired-in device. Tip: It doesn’t matter which set
button you use when adding it to the Insteon for
Hub app. Use the ‘add by ID’ option if necessary.
Follow the manual linking process described in the product manual
for the controller from which you plan to use with this device.
Referencing the table below, tap the Ceiling Fan Controller’s Fan Set
button until beeper and Fan LED indicate the desired fan speed.
For more information about manually linking and unlinking, see the
user manual online at www.insteon.com/get-started-2475f
If you do not own the Insteon Hub (2245-xxx), ISY-99,
or other Insteon compatible central controller, see the
Manual Linking section below. We strongly recommend
a central controller for managing Insteon devices,
especially for devices not easily accessible after
installation such as the Ceiling Fan Controller.
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en
compromettre le fonctionnement.
See Owner’s Manual for warranty information. Protected under U.S. and foreign patents (see
www.insteon.com/patents). ©2018 Insteon
Example of the control screen in the
Insteon for Hub app. Requires
Insteon Hub, sold separately.
Line
LIGHT
FAN
Light*
Neutral
Ceiling Fan
Fan
*If your ceiling fan has lights attached, make sure they are
dimmable. Quality of dimming varies by type and brand.
Wiring Diagram
A. Write down the Ceiling Fan Controller’s Insteon ID for future reference
B. Using your fan’s pull chains, turn light on and set fan to highest speed. Note: All
fan and light controls will be conducted through Ceiling Fan Controller once installed.
C. Turn off the circuit breaker supplying power to the fan
D. Remove the ceiling fan from the electrical box. Refer to the fan’s installation guide
for help if necessary.
E. Disconnect the wires from the ceiling fan (and light, if applicable)
F. Connect Ceiling Fan Controller per the wiring diagram. If your fan does not have a
light, cap the blue wire with the included wire nut.
G. Ensure all connections are secure with no exposed copper
H. Turn the breaker back on. The Ceiling Fan Controller’s Fan LED will be red and
Light LED will be green (connected lights will turn on). Tapping Light Set Button will
turn lights off.
I. Wait to re-install your fan until after linking the Ceiling Fan Controller
Low1st tap
2nd tap
3rd tap
4th tap
Medium
High
Off None
Fast double-beep
Single-beep Blinks green slow
Blinks green med
Blinks green fast
Double-beep
Red
CFL LED
Incandescent
& Halogen
Dimmable
CFL
Dimmable
LED
