Insteon Remotelinc 2 2444a2wh4 User manual

2444A2xx4 Rev. 7/16/2012 10:08 AM / See Owner’s Manual for Warranty Information, Patented

Power

Switch

(Left=Off,

Right=On)

Status LED

Set button

Micro-USB

Charging

Jack

Quick Start Guide

RemoteLinc™2 - INSTEON®

Wireless Keypad

Model: 2444A2WH4

Introduction

Conveniently control your home’s INSTEON network with the compact and

versatile RemoteLinc 2 wireless keypad controller.

What's Included

•RemoteLinc 2

Getting Started

Fully charge RemoteLinc 2 prior to programming (or anytime the unit is not

responding) using a Type A to Micro-B USB cable (sold separately). The

red Charging LED will turn off once the battery is fully charged

(approximately one hour). Slide the power switch to the ON position.

Note: RemoteLinc 2 requires an INSTEON dual-band or RF device to

communicate with other devices on your INSTEON network.

RemoteLinc 2 uses a subtle beeper sound to assist setup. It is

recommended that you program the unit in a quiet area.

Using RemoteLinc 2

RemoteLinc 2 contains four on/off button pairs (a-d). Each pair controls its own scene, sending commands to

devices linked specifically to that on/off button pair. Dimmable responders may behave differently, depending on

whether you tap, double-tap or press and hold a button to activate/deactivate a scene. Non-dimming responders

will only turn full-on or full-off, no matter what method you use.

Tap

Double-tap

Press and hold

Ramp to preset on-level or

off

Full-on or full-off instantly Brighten or dim until

released

The RemoteLinc 2 Status LED will flash green once for each on/brighten command

sent and red once for each off/dim command sent.

Warning:RemoteLinc 2 is permanently sealed. Do not attempt to open case. Doing so will damage the remote

and void the warranty.

Add RemoteLinc 2 (Button) as an INSTEON Controller

1) Tap ^on the RemoteLinc 2 scene button of choice

2) Adjust the responder to the state you want when the scene is activated from RemoteLinc 21

3) Press and hold RemoteLinc 2's Set button until RemoteLinc 2 beeps

RemoteLinc 2’s Status LED will begin blinking green

4) Press and hold the responder’s Set button until the responder beeps or its LED flashes

RemoteLinc 2 will double-beep and its LED will stop blinking

Responder’s LED will stop blinking (it may also double-beep)

5) Confirm that scene addition was successful by tapping on/off on the programmed RemoteLinc 2 button

The responder will toggle between the scene’s preset on-level and off

1If the responder is a multi-scene device such as a KeypadLinc, tap the scene button you wish to control until its LED is in the desired state (on or off)

4 Scene Buttons

(Left=Off/dim,

Right=On/brighten)

Charging LED

(inside case)

Owner’s Manual and Tech Support

Owner’s Manual and current Quick Start Guide: http://www.insteon.com/support

Call: INSTEON Support Line at 800-762-7845

2444A2xx4 Rev. 7/16/2012 10:08 AM / See Owner’s Manual for Warranty Information, Patented

RemoteLinc 2 Accessories

Wall Mount Bracket

(2444B4)

•Wall mount your RemoteLinc 2 anywhere

•Gang two or more together for more control

•Can be installed adjacent to existing wired-in switches

•Easily remove RemoteLinc for portability or recharging

•Use with any decorator wallplate

Visor Clip

(Available in the 2444Bxx kit)

•Control your home from your vehicle

•Turn lights on when you arrive and off

when you leave

Tabletop Stand

(Available in the 2444Bxx kit)

•Perfect for a nightstand, kitchen counter or

coffee table

USB Charging Cable (Type A to Micro-B)

(2444B5)

•Works with RemoteLinc 2 and any other

device that uses USB Type A to Micro-B

USB Power Adapter

(2444B6)

•For use with RemoteLinc 2 USB

Charging Cable and any other device

that charges via USB cable

Pair the Wall Mount Bracket with any decorator-style

wall plate (sold separately) for the perfect wireless

wall switch solution

This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Ce dispositif est conforme aux règlements de la FCC et aux normes CNR exemptes de licence d’Industrie Canada. Son fonctionnement est assujetti aux deux conditions suivantes: (1) ce

dispositif ne doit pas causer d’interférences nuisibles, et (2) ce dispositif doit accepter toute interférence qu’il reçoit, y compris les interférences pouvant nuire à son fonctionnement.

Other INSTEON Keypad manuals