INSTEON RemoteLinc 2 User manual

2444A2xx4 Rev. 7/5/2012 10:15 AM / See Owner’s Manual for Warranty Information, Patented
© Copyright 2012, INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845
Power
Switch
(Left=Off,
Right=On)
Status LED
Set button
Micro-USB
Charging
Jack
Quick Start Guide
RemoteLinc™2 - INSTEON® Wireless Keypad
Model: 2444A2WH4
Introduction
Conveniently control your home’s INSTEON network with the compact and
versatile RemoteLinc 2 wireless keypad controller.
What's Included
•RemoteLinc 2
Getting Started
Fully charge RemoteLinc 2 prior to programming (or anytime the unit is not
responding) using a Type A to Micro-B USB cable (sold separately). The
red Charging LED will turn off once the battery is fully charged
(approximately one hour). Slide the power switch to the ON position.
Note: RemoteLinc 2 requires an INSTEON dual-band or RF device to
communicate with other devices on your INSTEON network.
RemoteLinc 2 uses a subtle beeper sound to assist setup. It is
recommended that you program the unit in a quiet area.
Using RemoteLinc 2
RemoteLinc 2 contains four on/off button pairs (a-d). Each pair controls its own scene, sending commands to
devices linked specifically to that on/off button pair. Dimmable responders may behave differently, depending on
whether you tap, double-tap or press and hold a button to activate/deactivate a scene. Non-dimming responders
will only turn full-on or full-off, no matter what method you use.
Tap
Double-tap
Press and hold
Ramp to preset on-level or
off
Full-on or full-off instantly Brighten or dim until
released
The RemoteLinc 2 Status LED will flash green once for each on/brighten command
sent and red once for each off/dim command sent.
Warning:RemoteLinc 2 is permanently sealed. Do not attempt to open case. Doing so will damage the remote
and void the warranty.
Add RemoteLinc 2 (Button) as an INSTEON Controller
1) Tap ^on the RemoteLinc 2 scene button of choice.
2) Adjust the responder to the state you want when the scene is activated from RemoteLinc 2.1
3) Press and hold RemoteLinc 2's Set button until RemoteLinc 2 beeps.
RemoteLinc 2’s Status LED will begin blinking green.
4) Press and hold the responder’s Set button until the responder beeps or its LED flashes.
RemoteLinc 2 will double-beep and its LED will stop blinking.
Responder’s LED will stop blinking (it may also double-beep).
5) Confirm that scene addition was successful by tapping on/off on the programmed RemoteLinc 2 button.
The responder will toggle between the scene’s preset on-level and off.
1If the responder is a multi-scene device such as a KeypadLinc, tap the scene button you wish to control until its LED is in the desired state (on or off).
4 Scene Buttons
(Left=Off/dim,
Right=On/brighten)
Charging LED
(inside case)
Owner’s Manual and Tech Support
Owner’s Manual and current Quick Start Guide: http://www.insteon.com/support
Call: INSTEON Support Line at 800-762-7845

2444A2xx4 Rev. 7/5/2012 10:15 AM / See Owner’s Manual for Warranty Information, Patented
© Copyright 2012, INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845
RemoteLinc 2 Accessories
Wall Mount Bracket
(2444B4)
•Wall mount your RemoteLinc 2 anywhere.
•Gang two or more together for more control.
•Can be installed adjacent to existing wired-in switches.
•Easily remove RemoteLinc for portability or recharging.
•Use with any decorator wallplate.
Visor Clip
(Available in the 2444Bxx kit)
•Control your home from your vehicle.
•Turn lights on when you arrive and off
when you leave.
Tabletop Stand
(Available in the 2444Bxx kit)
•Perfect for a nightstand, kitchen counter or
coffee table.
USB Charging Cable (Type A to Micro-B)
(2444B5)
•Works with RemoteLinc 2 and any other
device that uses USB Type A to Micro-B.
USB Power Adapter
(2444B6)
•For use with RemoteLinc 2 USB
Charging Cable and any other device
that charges via USB cable.
Pair the Wall Mount Bracket with any decorator-style
wall plate (sold separately) for the perfect wireless
wall switch solution.
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.